• 콘크리트학회논문집
• /
• 제15권2호
• /
• pp.314-322
• /
• 2003

콘크리트 구조물의 수화열 저감 방안으로 사용되는 파이프 쿨링 시스템을 적용할 경우 파이프 관 주변의 내부유동에 의한 열전달이 발생하게 된다. 이와 같은 내부유동에 의한 열전달 효과를 정확히 규명하기 위해서는 유수대류계수를 산정하여야 한다. 파이프 쿨링 효과의 규명에 필요한 유수대류계수의 영향인자로는 냉각수의 층난류 여부, 냉각수의 유동속도, 관의 형상 및 열특성 등이 있다. 본 연구에서는 유수대류계수를 산정하기 위한 실험장치를 개발하였으며, 이를 이용하여 강재 및 PVC 파이프에 대한 실험을 수행하였다. 이들 실험결과를 토대로 관의 내부표면이 매끈한 원형관이며 난류흐름을 갖는 내부유동에 대한 유수대류계수 모델식을 제안하였으며, 제안된 모델식은 냉각수의 유속뿐만 아니라 유동관의 재질 및 형상을 고려할 수 있다. 유수대류계수는 관을 흐르는 냉각수의 대류에 의한 열전달 효과를 나타내는 값으로 관의 열전도율 및 관의 직경과는 비례관계에 있으며, 관의 두께와는 반비례관계를 갖는다. 본 연구에서 개발된 유수대류계수 모델식은 이러한 영향을 잘 반영하고 있으나, 강재 파이프에 대해서만 관의 두께 및 직경에 관한 보정계수를 제시하였다. 제안된 모델식에 의한 유수대류 계수와 실험으로부터 구한 유수대류계수를 비교한 결과, 제안된 모델식이 실험값을 정확히 추정하고 있음을 알 수 있었다.

• 한국기계가공학회지
• /
• 제6권4호
• /
• pp.3-7
• /
• 2007

The valve is used on control of flow in a ship. Flow coefficient of valve is very importance in the design of valve. In this paper, three-dimensional computer simulations by commercial code CFX were conducted to observe the valve type and to measure flow coefficient when valves with various angles and uniform incoming velocity were used in a piping system. By contrast, a group of experimental data is used to compare with the data obtained by CFX simulation to investigate the validity of numerical method.

• 대한기계학회논문집B
• /
• 제24권5호
• /
• pp.615-622
• /
• 2000

Numerical simulation is performed with Denton's code to get pressure loss coefficients in wide range of reverse flow incidence(from -90 degree to +85 degree) for an axial compressor cascade. As a results, it is found that the pressure loss coefficient is increased with incidence and there exist critical incidence which corresponds to the maximum pressure loss coefficient. Pressure loss coefficient with bigger incidence than its critical value is decreased. The effect of increasing incidence in a cascade extremely reduce the mass flow rate by the large flow separation region. Consequently this effect reduce the portion of dynamic pressure in the total pressure loss and beyond the critical incidence the pressure loss coefficient decrease.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제15권1호
• /
• pp.1-9
• /
• 2007

This study concerns the characteristics of helical flow in a concentric and eccentric annulus with a diameter ratio of 0.52 and 0.9, whose outer cylinders are stationary and inner ones are rotating. Pressure losses and skin friction coefficients have been measured for fully developed flows of water and 0.2% aqueous of sodium carboxymethyl cellulose (CMC), respectively, when the inner cylinder rotates at the speed of 0-500 rpm. The effect of rotation on the skin friction is significantly dependent on the flow regime. In all flow regimes, the skin friction coefficient is increased by the inner cylinder rotation. The change of skin friction coefficient corresponding to the variation of rotating speed is large for the laminar flow regime, whereas it becomes smaller as Re increases for the transitional flow regime and, then, it gradually approach to zero for the turbulent flow regime.

• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.39-47
• /
• 2011

Flow control range of valve, which is installed on pipeline, varies according to valve type, pipe diameter, pipe length, roughness, and elevation difference of both ends of pipeline. A lot of computation efforts and knowledge are needed to estimate flow control range of valve, considering above many parameters. The table of flow control range of each valve type is presented for convenience of pipeline design engineers who must make decision of valve size and type in this study. Also the reason that butterfly valve is recommended for flow control, and gate valve is forbidden is presented via quantification and figures in this study.

• Nuclear Engineering and Technology
• /
• 제52권7호
• /
• pp.1409-1416
• /
• 2020

The study of heat transfer coefficient of supercritical water plays an important role in improving the heat transfer efficiency of the reactor. Taking the supercritical natural circulation experimental bench as the research object, the effects of power, flow, pipe diameter and mainstream temperature on the heat transfer coefficient of supercritical water were studied. At the same time, the experimental data of Chen Yuzhou's supercritical water heat transfer coefficient was collected. Through the factorial design method, the influence of different factors and their interactions on the heat transfer coefficient of supercritical water is analyzed. Through the corresponding analysis method, the influencing factors of different levels of heat transfer coefficient are analyzed. It can be found: Except for the effects of flow rate, power, power-temperature and temperature, the influence of other factors on the natural circulation heat transfer coefficient of supercritical water is negligible. When the heat transfer coefficient is low, it is mainly affected by the pipe diameter. As the heat transfer coefficient is further increased, it is mainly affected by temperature and power. When the heat transfer coefficient is at a large level, the influence of the flow rate is the largest at this time.

• Nuclear Engineering and Technology
• /
• 제53권1호
• /
• pp.93-102
• /
• 2021

The analysis of the fluid flow characteristics in reactor pressure vessel is an important part of the hydraulic design of nuclear power plant, which is related to the structure design of reactor internals, the flow distribution at core inlet and the safety of nuclear power plant. The flow distribution and mixing characteristics in the pressurized reactor vessel for the 1000MWe advanced pressurized water reactor is analyzed by using Computational Fluid Dynamics (CFD) method in this study. The geometry model of the full-scaled reactor vessel is built, which includes the cold and hot legs, downcomer, lower plenum, core, upper plenum, top plenum, and is verified with some parameters in DCD. Under normal condition, it is found that the flow skirt, core plate holes and outlet pipe cause pressure loss. The maximum and minimum flow coefficient is 1.028 and 0.961 respectively, and the standard deviation is 0.019. Compared with other reactor type, it shows relatively uniform of the flow distribution at the core inlet. The coolant mixing coefficient is investigated with adding additional variables, showing that mass transfer of coolant occurs near the interface. The coolant mainly distributes in the 90° area of the corresponding core inlet, and mixes at the interface with the coolant from the adjacent cold leg. 0.1% of corresponding coolant is still distributed at the inlet of the outer-ring components, indicating wide range of mixing coefficient distribution.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2097-2101
• /
• 2007

This paper presents an optimal design of a micro evaporator which maximizes the heat transfer coefficient. Number of gaps, spanwise distance and streamwise distance are selected as the geometric design parameters. Mass flow rate of the refrigerant is selected as the non-geometric design parameter. Temperature at the surface of the heater is measured to valuate the heat transfer coefficient. Nine experiments are conducted using $L_9(3^4)$ orthogonal array. Maximum heat transfer coefficient is 640 W/$m^2K$ at the parameters of 2 gaps, 0.2 mm spanwise distance, 1.0 mm streamwise distance and 0.72 g/s mass flow rate. Among the 3 geometric parameters, the spanwise distance is the most sensitive parameter influencing the heat transfer coefficient. We conduct a second stage of experiment to increase the heat transfer coefficient by reselecting the mass flow rate. We concluded that 0.87 g/s is the optimized flow rate for an active micro cooler resulting in a heat transfer coefficient of 651 W/$m^2K$.

• 대한기계학회논문집B
• /
• 제23권11호
• /
• pp.1390-1398
• /
• 1999

A numerical analysis for ROT sparger of PWR(Pressurized Water Reactor) is carried out. Computation is performed to investigate the flow characteristics as the change of design factor. As the result of this study, RDT sparger's flow resistance coefficient is K=3.53 at the present design condition if engineering mar&in is considered with 20%, and flow ratio into branch pipe is $Q_s/Q_i=0.41$. Velocity distribution at exit is not uniform because of separation in branch pipe. In the change of inlet flow rate and section area ratio of branch pipe for main pipe, flow resistance coefficient is increased as $Q_s/Q_i$ decreasing, but in the change of branch angle and outlet nozzle diameter of main pipe, flow resistance coefficient is decreased as $Q_s/Q_i$ decreasing. As the change rate of $Q_s/Q_i$ is the larger, the change rate of flow resistance coefficient is the larger. The change rate of pressure loss is the largest change as section area ratio changing. The optimal design condition of sparger is estimated as the outlet nozzle diameter ratio of main pipe is $D_s/D_i=0.333$, the section area ratio is $A_s/A_i=0.2$ and the branch angle is ${\alpha}=55^{\circ}$.

• 한국산학기술학회논문지
• /
• 제17권7호
• /
• pp.734-739
• /
• 2016

선형으로 움직이는 글로브 밸브의 목적은 주로 유량을 제어할 수 있도록 설계 되어 있으며, 디스크의 움직임으로 인해서 유량을 제어가 가능하게 된다. 본 논문은 유량계수를 예측하기 위해서 전산유동해석 프로그램인 ANSYS-CFX로 유동해석을 진행 하였고 본 해석에서 사용되는 글로브 밸브 모델을 시제품과 동일한 형상의 크기로 설계하였다. 유량계수는 밸브 전개 시 $16.5^{\circ}C$의 맑은 물이 전후의 압력차 1psi로 흐를 때 그때의 유량을 말한다. 다시 말해서 밸브의 크기를 결정할 수 있는 중요한 요인이 된다. 밸브의 유량계수와 유량을 해석을 통해서 얻어낼 수 있었고, 그 해석으로 인해서 분당 0~0.1gal 유량을 제어할 수 있는 정밀제어 글로브 밸브를 개발 할 수 있었다. 유동해석과 실험의 결과로 유량계수를 서로 비교하였으며 그 결과로 인해서 유량계수의 오차율이 매우 작음을 확인하였고, 해석의 신뢰성을 확보하였다. 따라서 실험 없이 해석만으로 충분히 유량계수의 경향성을 파악하는데 크게 어려움이 없음을 보여주었다.