• Fibers and Polymers
• /
• v.6 no.4
• /
• pp.289-296
• /
• 2005

Biodegradable nanocomposites were prepared by mixing a polymer resin and layered silicates by the melt intercalation method. Internal structure of the nanocomposite was characterized by using the small angle X-ray scattering (SAXS) and transmission electron microscope (TEM). Nanocomposites having exfoliated and intercalated structures were obtained by employing two different organically modified nanoclays. Rheological properties in shear and extensional flows and biodegradability of nanocomposites were measured. In shear flow, shear thinning behavior and increased storage modulus were observed as the clay loading increased. In extensional flow, strain hardening behavior was observed in well dispersed system. Nanocomposites with the exfoliated structure had better biodegradability than nanocomposites with the intercalated structure or pure polymer.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.9
• /
• pp.768-778
• /
• 2003

Numerical analysis has been carried out to investigate laminar convective heat transfer in a tube for supercritical water near the thermodynamic critical point. Fluid flow and heat transfer are strongly coupled due to large variations of thermodynamic and transport properties such as density, specific heat, viscosity, and thermal conductivity near the critical point. Heat transfer characteristics in the developing region of the tube show transition behavior between liquid-like and gas-like phases with a peak in heat transfer coefficient distribution near the pseudocritical point. The peak of the heat transfer coefficient depends on pressure and wall heat flux rather than inlet temperature and Reynolds number, Results of the modeling provide convective heat transfer characteristics including velocity vectors, temperature, and the properties as well as the heat transfer coefficient. The effect of proximity to the critical point is considered and a heat transfer correlation is suggested for the peak of Nusselt number in the tube.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.65-69
• /
• 2007

A design of experiments was applied in order to investigate the effect of processing variables in UV irradiation on the electrical/optical properties in indium-zinc oxide thin films, The processing variables, equivalently input variables are listed as UV irradiation time, oxygen flow rate, and chamber pressure. The statistical significance of Ultra Violet (UV) treatment was confirmed using a paired-t test. The full factorial $2^3$ design was employed to determine significant main and interaction effects in UV irradiation process. The chamber pressure and the interaction between UV irradiation time and $O_2$ flow rate were found to be statistically significant at the significance level of 0.1. Furthermore, the optimized approach was proposed in achieving the improved conductivity after UV irradiation.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1296-1297
• /
• 2006

Both plastic and elastic properties change dramatically from the beginning to the end of the compaction phase. Previous investigations have shown that powder transfer and high powder flow during initial compaction at low density affects the strength of the final component significantly. Investigated here are shear failure and elastic shear modulus in the low density range for hard metal powder and for pre-alloyed water atomized iron powder. Direct shear test equipment for sand and clay has been modified to measure the shearing properties of powder for an axial loading between 1 kPa and 500 kPa.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1242-1247
• /
• 2000

Results from a study on the effect of the chemical agent on the flowing and setting properties of high flowing.high strength concrete using blast-furnace slag are presented in this paper. The flowing and setting properties of concrete are investigated by slump, slump-flow, flowing velocity, L-flow, velocity of V-funnel, L-spatial passability and setting time. In addition, kinds of chemical agent were composed of naphthalene type, of naphthalene and melamine and melamine type. The results indicate that dispersive capacity can be increased by naphthalene composition. Also, it shows that viscosity and early strength can be increased by melamine composition.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.145-146
• /
• 2017

This research aimed to analyze the fundamental properties of cement mortar accompanying the change of the solid contents of the maintenance type PC water reducing agent. As a result of the experiment, it was found that the properties of fresh mortar show a tendency to decrease as the solid contents decreases in the case of flow and air contents, and the decrease width with time is small. It was found that the compressive strength of the hardened mortar has almost no difference due to the change of the solid fraction.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.22-23
• /
• 2017

This research aimed to analyze the fundamental properties of cement mortar accompanying the change of solid contents of PC type water reducing agent. As a result of the experiment, in the case of flow to the properties of the fresh mortar, it shows a tendency to decrease as the solid content ratio decreases, and the decrease width with the passage of time is greatly reduced when 30 minutes passed since the passage of 60minutes It turned out that it was. In the case of the air contents and the compressive strength, it was found that there is almost no difference due to the change in the solid contents.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.318-320
• /
• 2013

The spherical bead manufactured by rapidly cooling process shows high density of 3.64g/㎤, high unit volume weight of 2.6kg/l, and high solid volume of 71%. When it applies to the grouter, it is possible to obtain even high fluidity with only a small amount. This study, focusing the grouter using a rapidly-cooled electric arc furnace oxidizing slag(RC-EAFS), deals with the properties of flow and setting time in fresh state, compressive strength and length variation at 1, 3, 7 and 28 curing day in hardened state. As the results, even though the grouter with RC-EAFS shows comparative low strength, it will be possible to development the competitive product due to the properties of increasing flow and low cost.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.339-342
• /
• 1997

The optical properties of WO$_3$thin films deposited by RF magnetron reactive sputtering were studied. The substrate was an ITO(indium-tin-oxide) glass(100$\Omega$/ ). The optical properties are examined by different deposition conditions. RF power, substrate temperature, $O_2$concentraction. Ar flow rate, working pressure and thickness are 40~60W, 25~30$0^{\circ}C$, 10%, 54~72sccm, 5~20m7orr and 1200~2400$\AA$, respectively. All these films were colorless, light yellow and found to be amorphous in structure by X-ray diffraction analysis. When RF power, substrate temperature, $O_2$concentraction, Ar flow rate, working pressure and thickness are 40W, $25^{\circ}C$, 10%, 72sccm, 20mTorr and 2400$\AA$, respectively the values of transmittance of the WO$_3$thin films in visible region are about 80%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.94-97
• /
• 1997

We investigated the sheet resistance properties of tungsten nitride thin films deposited by RF and DC sputtering system. It deposited at various conditions that determine the sheet resistance. The properties of the sheet resistance of these films were measured under various conditions. Sheet resistance analysed under the flow rate of the argon gas and contents of nitrogen from nitrogen-argon gas mixtures. We found that these sheet resistance were largely depend on the temperature of substrate, gas flow rate and RF power. Very high and low sheet resistance of tungsten films obtained by DC sputtering. As the increase of contents of nitrogen gas obtained from nitrogen-argon gas mixture, tungsten nitride thin films deposited by the reactive DC sputtering and the sheet resistance of these films were increased.