• International Journal of Fluid Machinery and Systems
• /
• v.5 no.3
• /
• pp.117-125
• /
• 2012

In the present experimental study, the authors try to clarify the characteristics of the flow around and inside a cross-flow impeller in a typical geometry, over a wide parameter range of an aspect ratio $L/D_2$. In order to eliminate the complicated casing factors, the impeller rotates in open space without any casings. As a result, by using hot wire anemometer measurements and by conventional flow visualisations with a particle image velocimetry technique, the authors show that both the outflow rate and the maximum vorticity attain the maximum for $L/D_2$ = 0.6. In order to investigate the aspect-ratio effect, we further reveal minute fluctuating pressures on an impeller end wall for a singular $L/D_2$ = 0.6. Especially in these pressure measurements, the eccentric vortex is prevented to revolute by the insertion of a tongue, in order to consider the spatial structure of flow more precisely.

• Korea-Australia Rheology Journal
• /
• v.20 no.1
• /
• pp.27-34
• /
• 2008

Clay suspensions in liquid polymers exhibit a time-dependent behaviour that includes viscoelastic as well as thixotropic features. Because of the presence of interacting clay platelets, particulate networks can develop, which are broken down during flow and rebuild upon cessation of the flow. Here, the use of thixotropic techniques in probing flow-induced structures in nanocomposites is explored with data on a hectorite-poly(isobutylene) model system. By means of fast stress jump measurements the hydrodynamic contributions to the steady state stresses are determined as well as those caused by the stretching of the clay floes. Flow reversal measurements do not provide a clear indication of flow-induced anisotropy in the present case. The recovery of the clay microstructure upon cessation of flow is followed by means of overshoot and dynamic measurements. The development of a particulate network is detected by the appearance and growth of a low frequency plateau of the storage moduli. The modulus-frequency curves after various rest times collapse onto universal master curves, regardless of the pre-shear history or temperature. The scaling factors for this master curve are the crossover parameters. The crossover moduli are nearly a linear function of the crossover frequency, the relation being identical for recovery after shearing at different shear rates. This function depends, however, on temperature.

• Journal of Oral Medicine and Pain
• /
• v.46 no.4
• /
• pp.109-116
• /
• 2021

Purpose: Xerostomia is subjective feeling of dry mouth. It is complicated and multifactorial, which burdens clinicians in diagnosis and treatment of the problem. The goal of this study was to discuss the clinical importance of salivary flow rate, pH and subjective symptoms for evaluating oral dryness among young healthy male subjects. Methods: Thirty male participants were recruited in this study (mean age±standard deviation of 25.70±1.84). All participants completed 'Xerostomia Inventory' to measure subjective oral dryness scores. Unstimulated saliva and stimulated saliva were collected from each participant twice a day at 12:00 pm and 5:00 pm, using spitting method. Salivary flow rates and pH were measured immediately after collection. Relationship between objective and subjective measurements were analyzed. Results: There were excellent intra-examiner reliability for salivary flow rate and pH and good internal consistency for Xerostomia Inventory. Objective measurements and subjective symptoms did not exhibit positive association. Salivary flow rate in unstimulated and stimulated condition showed positive association and also for salivary pH. Stimulated salivary flow rate also presented positive correlation with stimulated salivary pH. Conclusions: Comprehensive assessment of objective measurements and subjective symptoms may be complimentary for assessing oral dryness, which would assist in implementing early interventions to improve patient's quality of life.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.117-123
• /
• 2007

There has been considerable interest in recent years in field-responsive suspensions, which are of some importance in industry in many different applications. The microstructure of these materials is a significant issue which can be probed by rheological measurements. In this study, measurements were made of a magnetorheological fluid (MRF) under steady and oscillatory shear flow, with and without a magnetic field. Mathematical inversion was used to derive the relaxation time spectrum of the MRF from oscillatory shear data. Experimental evidence is presented of the gel-like properties of this MRF.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.4
• /
• pp.360-368
• /
• 2010

This paper describes the flow field and the blade pressure distribution of a horizontal axis wind turbine in various yawed flow conditions. These measurements were carried out with 2.4m-diameter rotor with pressure sensors and a 2-dimensional laser Doppler velocimeter for each azimuth angle in a wind tunnel. The results show that aerodynamic forces of the blade based on the pressure measurements change according to the local angle of attack during rotation. Therefore the wake of the yawed rotor becomes asymmetric for the rotor axis. Furthermore, the relations between aerodynamic forces and azimuth angles change according to tip speed ratio. By the experimental analysis, the flow field and the aerodynamic forces for each azimuth angle in yawed flow condition were clarified.

• Journal of the Korean Society of Visualization
• /
• v.10 no.2
• /
• pp.20-24
• /
• 2012

Increasing the active catalyst surface area is important in improving a converter's efficiency. In addition, uniform flow is advantageous in that it produces more efficient catalytic conversion. This results in the ability to use a smaller catalytic converter with uniform flow as opposed to a larger converter requirement for non-uniform flow. Therefore, it is important to characterize the internal flow of the catalytic converter. To characterize the system's flow patterns, velocity measurements were taken at the mid and exit planes of a ceramic honeycomb catalytic converter at flow rates of 37.8 l/s and 94.4 l/s. Measurements were conducted using LDV. The profiles were measured along both the major and minor axis of the planes. Primary flow direction velocities measured along the minor axis, at both flow rates, varied greatly at the mid plane and somewhat at the exit plane. The areas of greatest air flow were seen near the edges of the walls and on the side of the converter opposite the flow's entrance region. It also appears that the high velocities opposite the intake are due to the design of the entrance region. The entrance region is possibly too small to properly redirect the vertically entering fluid into an evenly distributed flow in the primary flow direction.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.401-402
• /
• 2006

The turbulent flow around a sphere was investigated using two experimental techniques: smoke-wire flow visualization in wind tunnel at Re=5300, 11000 and PIV measurements in a circulating water channel. The smoke-wire visualization shows flow separation points near an azimuthal angle of $90^{\circ}$, recirculating flow, transition from laminar to turbulent shear layer, evolving vortex roll-up and fully turbulent eddies in the sphere wake. The mean velocity field measured using a PIV technique in x-y center plane demonstrates the detailed near-wake structure such as nearly symmetric recirculation region, two toroidal vortices, laminar separation, transition and turbulent eddies. The PIV measurements of turbulent wake in y-z planes show that a recirculating vortex pair dominates the near-wake region.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.1
• /
• pp.13-19
• /
• 1995

An experimental investigation has been made for flow in a circular cylinder with a rotating bottom disk. Flow system considered in this paper is a characteristic model of interior flows of an electric washing machine. Flows in a tub of an electric washing machine are driven by a rotating bottom disk called a pulsator. The simple and characteristic model was composed of a circular cylinder with impulsively rotating endwall disk and a viscous fluid in it. Rotational motion of the pulsator is periodic and alternative in rotation direction. The flow field in the interior region is governed by a horizontal boundary layer forms on the impulsively rotating disk. Experimental approach was accomplished by adopting an image processing technique for velocity measurements. Comprehensive details of the flow structure are presented. Also a meridional circulation is obtained by tracking image particles suspended in the fluid. Flow structure and data are successfully procured for this complex rotating flow field.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.73-77
• /
• 2006

Flow rate measurement is one of the difficult problems in the industrial applications. Especially, flow rate in a partially filled pipeline is affected by many parameters such as water level, channel slop, etc. In the present study, prior to the development of a flowmeter, the flow characteristics has been investigated by particle image velocimetry (PIV) measurements. Three-dimensional velocity distributions were obtained from sectional measurements of velocity profiles according to the water level. As a result, it is found that there is no similarity in the velocity profile when the lateral position is changed. In addition, the maximum velocity does not always occur on the free surface. It depends on the water level. In the aspect of flow rate measurement, the previous calculus based upon point measurement techniques is proved to be inaccurate because of the lack of whole flow information.

• Wind and Structures
• /
• v.19 no.1
• /
• pp.75-88
• /
• 2014

The computational fluid dynamic is used to explore new aspects of the hill flow. This analysis focuses on flow dependency and the comparison of results from measurements and simulations to show an optimization turbulent model and the possibility of replacing measurements with simulations. The first half of the paper investigates a suitable turbulence model for determining a suitable site for a wind turbine. Results of the standard k-${\varepsilon}$ model are compared precisely with the measurements taken in front of the hilltop, The Reynolds Stress Model showed exact results after 1.0 times of hill steepness but the standard k-${\varepsilon}$ model and standard k-${\omega}$ model showed greater underestimation. In addition, velocity flow over Pha Taem hill topography and the reference geometry shape were compared to find a suitable site for a turbine in case the actual hill structure was associated with the trapezoid geometric shape. Further study of geometry shaped hills and suitable sites for wind turbines will be reported elsewhere.