• Journal of Bio-Environment Control
• /
• v.4 no.2
• /
• pp.188-194
• /
• 1995

This study was carried out to investigate the effect of NH$_4$H$_2$PO$_4$ on pH stabilization in deep flow culture system using tap water, and to determine the optimum range of NH$_4$H$_2$PO$_4$ in culture solution. The pH of tap water is 7.5. The higher the concentration of NH$_4$H$_2$PO$_4$ was, the more the pH of nutrient solution was decreased. In NH$_4$H$_2$PO$_4$ 4/3-5/3 me/$\ell$, the pH of nutrient solution was 6-7.5 during the experiment. The highest brix(%) was obtained in NH$_4$H$_2$PO$_4$ 5/3-6/3 me/$\ell$. Leaf length, leaf width and stem-base diameter were highest in NH$_4$H$_2$PO$_4$ 2/3 me/$\ell$. The L and b＊ values were highest and the a＊ value was lowest in NH$_4$H$_2$PO$_4$ 8/3 me/$\ell$. Toxicity symptom of ammonium appeared in NH$_4$H$_2$PO$_4$ 8/3 me/$\ell$. It suggests that there was the relationship between leaf color and growth condition. It was concluded that NH$_4$H$_2$PO$_4$ 2/3 me/$\ell$ was good before harvest stage and NH$_4$H$_2$PO$_4$ 5/3-6/3 me/$\ell$ at harvest stage.

• Journal of Bio-Environment Control
• /
• v.27 no.1
• /
• pp.20-26
• /
• 2018

This study was conducted to develop a device for measuring the air flow by space variation through monitoring program, which acquires data by each point from each environmental sensor located in the greenhouse. The distribution of environmental factors(air temperature, humidity, wind speed, etc.) in the greenhouse is arranged at 12 points according to the spatial variation and a large number of measurement points (36 points in total) on the X, Y and Z axes were selected. Considering data loss and various greenhouse conditions, a bit rate was at 125kbit/s at low speed, so that the number of sensors can be expanded to 90 within greenhouse with dimensions of 100m by 100m. Those system programmed using MATLAB and LabVIEW was conducted to measure distributions of the air flow along the greenhouse in real time. It was also visualized interpolated the spatial distribution in the greenhouse. In order to verify the accuracy of CFD modeling and to improve the accuracy, it will compare the environmental variation such as air temperature, humidity, wind speed and $CO_2$ concentration in the greenhouse.

• Journal of Korea Water Resources Association
• /
• v.51 no.4
• /
• pp.347-354
• /
• 2018

In urban areas, runoff flow is drained through sewer networks as well as surface areas. Therefore, it is very important to consider sewer networks as a component of hydrological drainage processes when conducting urban inundation modelling. However, most researchers who have implemented urban inundation/flood modelling, instinctively simplified the sewer networks without the appropriate criteria. In this research, a 1D-2D fully coupled urban inundation model is applied to estimate the influence of sewer network simplification on urban inundation modelling based on the dendritic network classification. The one-dimensional (1D) sewerage system analysis model, which was introduced by Lee et al. (2017), is used to simulate inlet and overflow phenomena by interacting with surface flow. Two-dimensional (2D) unstructured meshes are also applied to simulate surface flow and are combined with the 1D sewerage analysis model. Sewer network pipes are simplified based on the dendritic network classification method, namely the second and third order, and all cases of pipes are conducted as a control group. Each classified network case, including a control group, is evaluated through their application to the 27 July 2011 extreme rainfall event, which caused severe inundation damages in the Sadang area in Seoul, South Korea. All cases are compared together regarding inundation area, inflow discharge and overflow discharge. Finally, relevant criterion for the simplification method is recommended.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.160-166
• /
• 2018

The worldwide semi-conductor market has been growing for a long time. Manufacturing lines of semi-conductors need to handle several types of toxic gases. In particular, they need to be controlled accurately in real time. This type of toxic gas control system consists of many different kinds of parts, e.g., fittings, valves, tubes, filters, and regulators. These parts obviously need to be manufactured precisely and be corrosion resistant because they have to control high pressure gases for long periods without any leakage. For this, surface machining and hardening technologies of the metal block and metal gasket need to be studied. This type of study depends on various factors, such as geometric shapes, part materials, surface hardening method, and gas pressures. This paper presents strong concerns on a series of simulation processes regarding the differences between the inlet and outlet pressures considering several different fluid velocity, tube diameters, and V-angles. Indeed, this study will very helpful to determine the important design factors as well as precisely manufacture these parts. The EP (Electrolytic Polishing) process was used to obtain cleaner surfaces, and hardness tests were carried out after the EP process.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.6
• /
• pp.449-469
• /
• 2011

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering during 2010. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) Research trends of thermal and fluid engineering have been surveyed as groups of general thermal and fluid flow, fluid machinery, and new and renewable energy. Various topics were presented in the field of general thermal and fluid flow. Research issues mainly focused on the thermal reliability of axial fan and compressor in the field of fluid machinery. Studies on the design of ground source heat pump systems and solar chemical reactors were executed in the field of new and renewable energy. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer in thermoelectric cooling/power generation systems, combined heat and power systems, carbon nano fluid with PVP, channel filled with metal foam and smoke ventilation in a rescue station of a railroad tunnel. Also the studies on flow boiling of R123/oil mixture in a plain tube bundle and R410A charge amount in an air cooled mini-channel condenser were reported. In the area of industrial heat exchangers, researches on plate heat exchanger, shell and tube heat exchanger, enthalpy exchanger, micro channel PCHE were performed. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics and industrial heat exchangers. Researches on heat transfer characteristics included heat transfer in thermoelectric cooling/power generation systems, combined heat and power systems, carbon nano fluid with PVP, channel filled with metal foam and smoke ventilation in a rescue station of a railroad tunnel. Also the studies on flow boiling of R123/oil mixture in a plain tube bundle and R410A charge amount in an air cooled mini-channel condenser were reported. In the area of industrial heat exchangers, researches on plate heat exchanger, shell and tube heat exchanger, enthalpy exchanger, micro channel PCHE were performed. (3) Refrigeration systems with alternative refrigerants such as hydrocarbons, mixed refrigerants, and CO2 were studied. Performance improvement of refrigeration systems are tried applying various ideas of refrigerant subcooling, dual evaporator with hot gas bypass control and feedforward control. The hybrid solar systems combining the solar collection devices with absorption chillers or compression heat pumps are simulated and studied experimentally as well to improve the understanding and the feasibility for actual applications. (4) Research trend in the field of mechanical building facilities has been found to be mainly focused on field applications rather than performance improvements. Various studies on heating and cooling systems, HVAC facilities, indoor air environments and energy resources were carried to improve the maintenance and management of building service equipments. In the field of heating and cooling systems, papers on a transformer cooling system, a combined heat and power, a slab thermal storage and a heat pump were reported. In the field of HVAC facilities, papers on a cooling load, an ondol and a drying were presented. Also, studies on HVAC systems using unutilized indoor air environments and energy resources such as air curtains, bioviolence, cleanrooms, ventilation, district heating, landfill gas were studied. (5) In the field of architectural environment and energy, studies of various purposes were conducted such as indoor environment, building energy, renewable energy and green building. In particular, renewable energy and building energy-related researches have mainly been studied reflecting the global interest. In addition, many researches which related the domestic green building certification of school building were performed to improve the indoor environment of school.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.594-600
• /
• 2017

HVDC transmission systems can be configured in many ways to take into account cost, flexibility and operational requirements. [1] For long-distance transmission, HVDC systems may be less expensive and suffer lower electrical losses. For underwater power cables, HVDC avoids the heavy currents required to charge and discharge the cable capacitance of each cycle. For shorter distances, the higher cost of DC conversion equipment compared to an AC system may still be warranted, due to other benefits of direct current links. HVDC allows power transmission between unsynchronized AC transmission systems. Since the power flow through an HVDC link can be controlled independently of the phase angle between the source and the load, it can stabilize a network against disturbances due to rapid changes in power. HVDC also allows the transfer of power between grid systems running at different frequencies, such as 50 Hz and 60 Hz. This improves the stability and economy of each grid, by allowing the exchange of power between incompatible networks. This paper proposed to establish Korean HVDC technology through a cooperative agreement between KEPCO and LSIS in 2010. During the first stage (2012), a design of the ${\pm}80kV$ 60MW HVDC bipole system was created by both KEPCO and LSIS. The HVDC system was constructed and an operation test was completed in December 2012. During the second stage, the pole#2 system was fully replaced with components that LSIS had recently developed. LSIS also successfully completed the operation test. (2014.3)

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.44-51
• /
• 2005

Water flow in rivers during flood season can be 10 to 100 fold higher than normal seasons (low precipitation) in Japan and predicting flood runoff is essential for operating reservoirs with discharging gates. Abundant experiences and knowledge are requisites for operators to be able to make efficient decisions at work. This research investigated a method to transfer technical knowledge by acquiring skills and knowledge from actual dam operators and by using the information to construct an educational training system. The purpose of the research was to enable the execution of a secure and rational reservoir operation during flood period. The educational training system for reservoir operation was developed with the focuses on acquiring knowledge on hydraulics and hydrology and learning about decision making related to the reservoir operation as well as the timing of control. The system is capable of conducting education that corresponds to individual levels in each location. Of the educational training methods, a lecture method that uses textbooks is effective for the understanding of basic knowledge and concepts while a training method that uses a simulation device is essential for the practice of advanced and specialized procedures in specific fields. Simulation devices are used in operational training for airplane flight and driving cars and trains. The educational system presented here was designed to provide further assistance to those who have acquired basic knowledge and concepts through textbooks and also to at low them to perform the satisfactory operation of dam equipment. Our research proposes a method which can realize a system to acquire technical skills-the skills which are the foundation of technical knowledge and operation.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.1
• /
• pp.1-8
• /
• 1996

A conveyor system in corrugated manufacturing industry may be in charge of carriage/storage, and may control logistics flow and production activities of products in a manufacturing process which consists of corrugators, conveyors, and printer-slotter systems. It identifies problems that the conveyor system in this case study is overloaded and often operated manually. This research is to evaluate e the conveyor system though simulation model of technological evaluation beyond d eco-nomic and qualitative one. The rate of operation and the load of the conveyor system are used as parameters in the simulation. This paper suggests a direction to a new conveyor system implementation the basis of the results that are derived by new alternatives based on current model. The best alternative is supposed to be the number of conveyors and the operation times of the printer-slotter that may be increased at the same time.

• Journal of Digital Contents Society
• /
• v.18 no.2
• /
• pp.403-410
• /
• 2017

In this paper, the fire extinguisher maintenance system using smart NFC communication and the real-time pressure measurement is proposed. The proposed system consists of three steps in the flow of information. The first step is to identify the fire extinguisher through NFC tagging in the fire extinguisher module using the smart device. The fire extinguisher appearance check and the real-time pressure measurement is performed in the second step, and the last step sends the check status information to the management server. In particular, the actual pressure value is calculated based on the angle of the green area and the indicating needle. Some experiments are conducted so as to verify the proposed system, and as a result, the proposed system shows that the administrator can effectively control the status information of fire safety check.

• Journal of Veterinary Clinics
• /
• v.24 no.4
• /
• pp.514-521
• /
• 2007

The sympathetic nerve block improves the blood flow in the innervated regions. For this region, the sympathetic nerve block has been performed in the neural and cerebral disorders. However, the cerebral blood flow regulation of the cranial cervical ganglion block in dogs have not been well defined and the correlation to the changes in the cerebral circulation and the changes in the electroencephalogram is not well defined in dogs yet. Therefore, we investigated the hypothesis that changes in the EEG could be affected by the changes in cerebral blood flow following the cranial cervical ganglion block in dogs. Twenty five beagle dogs were divided into 3 groups; group I(LCCGB, n=10) underwent left sided cranial cervical ganglion block using the 1% lidocaine, group II(L, n=10) injected the 1% lidocaine into the right or left sided digastricus muscle, group III(N/SCCGB, n=5, served as control) underwent the left sided cranial cervical ganglion block using saline. A statistical difference was not found between the control group and the LCCGB group in the 95% spectral edge frequency(SEF) and the median frequency(MF). In the relative band power, the $\delta$ frequency was decreased during 5-25 min, while the $\alpha$ frequency was increased during the same time(p<0.05). But the $\theta$ frequency and the $\beta$ frequency were not shown the significant changes compared with the control group during the same time(p<0.05). These results suggest that the left cranial cervical ganglion block does not induce the change of the cerebral blood flow and its effect is insignificant.