• Journal of the Korea Institute of Building Construction
• /
• v.1 no.2
• /
• pp.185-190
• /
• 2001

The purpose of this study is the development of practical Dry floor tile unit method that settle the defect of a wet method and designed for resin mat. With use of PE resin which is confirmed the basic property, it is developed that resin mat, joint-sealing compound with fixed form and space management to Dry floor tile unit method. The result of this study is below. 1) To acquire above the 4kgf/$\textrm{cm}^2$ - construction specification criterion, the bonding space that between resin mat and tile has to occupy the 50% of resin mat module space(10,000$\textrm{cm}^2$). 2) Criteria of bonding part plane is below. simpleness of metal form. productivity, uniform quality after injection molding cooling, easy cutting for remain space management, adhesive property, construction ability, transformation of a severed piece under pressure and so on. 3) To get the shape that could protect the interfacial breakdown, it is designed that resin mat and tile are unified after the bond input. 4) Adapted joint-sealing compound is the material of urethane kinds wedge form. Resin mat has the water passageway that could drain the water. 5) To manage the severed piece of tile, the resin mat is likely to divide the half and the quarter and the plastic drainage is developed in the severed piece.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.59-61
• /
• 2013

The purpose of this study was to present the necessary data concerning the selection and development of floor-coverings in view of slipperiness by comparing the relationship between CSR measured with O-Y·PSM and RCOF calculated from the result of gait analysis. CSR was calculated from maximum tensile load(Pmax) divided by perpendicular load(785N) when pulled 18 degrees upward the moment the bottom of the slip piece contacted the surface of the test piece. RCOF was calculated based on Fy/Fz from when horizontal load reached the maximum point within the sections from the moment the front of outsole touched the test piece to when pulled off the test piece. The results from the research were as follows: (1) Range of CSR was 0.15-1.02, which meant the differences of slipperiness of the test pieces definitely showed up. (2) RCOF are inadequate to express the characteristic about the slipperiness of the floors, since there were no differences between the test pieces.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.46 no.5
• /
• pp.353-357
• /
• 2020

Fractures of the orbital floor and walls are among the most frequent maxillofacial fractures. Virtual three-dimensional (3D) planning and use of patient-specific implants (PSIs) could improve anatomic and functional outcomes in orbital reconstruction surgery. The presented case was a victim of a terrorist attack involving improvised explosive devices. This 58-year-old female suffered severe wounds caused by a single piece of metal from a bomb, shattering the left orbital floor and lateral orbital wall. Due to remaining hypotropia of the left eye compared to the right eye, late orbital floor reconstruction was carried out with a personalised 3D printed titanium implant. We concluded that this technique with PSI appears to be a viable method to correct complex orbital floor defects. Our research group noted good aesthetic and functional results one year after surgery. Due to the complexity of the surgery for a major bony defect of the orbital floor, it is important that the surgery be executed by experienced surgeons in the field of maxillofacial traumatology.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.19 no.39
• /
• pp.293-299
• /
• 1996

The breakdown of machines lead to the lateness of parts and the change of schedules. Its treatment is very important problem in the shop floor control system. In this study, we present an algorithm minimize the lateness, earliness and change of schedule by controlling machining speed of available machines. Production time and production cost required to manufacture a piece of product are usually expressed as a unimodal convex fuction with respect to machining speed, and each has its minimal point at the minimum time speed or the minimum cost speed, and a speed range between these two speeds is called 'efficiency speed range'. Therefore, the algorithm determines the machining speed in the efficiency speed range. An example is demonstrated to explain the algorithm.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.4
• /
• pp.105-109
• /
• 2008

The purpose of this study is to distinguish the causes of broken glass on doors or windows when it is originally kept among the remains on the floor in fire site - whether it was broken due to heating or outer power-through test and characteristics of the broken plane including the pattern on the plane. Addition to it, the study tries to find characteristics to judge the point and direction of breakdown through the analysis of glass broken by outer power. With two assumed causes - a) breakdown due to heating and b) breakdown due to outer power-3 pieces of glass plates ($30cm{\times}30cm{\times}5mm$) were tested for each case, getting the results as following: First, for the glass broken due to the change of temperature, the broken plane is of slow and smooth curve without any pattern. Second, for the glass broken due to outer power, with the impact point as the center, the glass shows breakdown of radial type and the side shows breakdown of near-perpendicular type. The far the broken piece is from the impact point, the bigger the size is. The broken piece at the impact point is of long triangle type and the two long planes of the triangle shows semi-arc with the center of breakdown point and the other plane shows opposite pattern. Third, when glass that is damaged by outer power is heated, damaged forms and side patterns of the glass that is damaged by outer power are heated and disappeared.

• Journal of Korean Institute of Fire Investigation
• /
• v.3 no.1
• /
• pp.12-15
• /
• 2003

The purpose of this study is to distinguish the causes of broken glass from doors or windows when it is found being originally kept among the remains on the floor in fire site - whether it was broken due to heating or by outer power through test and the properties of the broken plane including the pattern on the plane. Addition to it, the study tries to find characteristics for judging the point and direction of breakdown through the analysis of glass broken by outer power. With two causes assumed - a. breakdown due to heating and b. breakdown due to outer power - 3 pieces of glass plates $(30cm{\times}30cm{\times}5mm)$ for each case were tested, getting the results as following: 1. For the glass broken due to the change of temperature The broken plane is of slow curve and smooth without any pattern. 2. For the broken due to outer power With the impact point as the center, the shows breakdown of radial type and the side shows breakdown of near-perpendicular type. The far the broken piece is from the impact point, the bigger the size is. The broken piece at the impact point is of long triangle type and the two long planes of the triangle shows semi-arc with the center of breakdown point and the other plane shows opposite pattern 3. Change of the pattern and type of the glass due to outer power The pattern and type of the glass due to outer power shows change due to heatihg.

• Journal of the Korean housing association
• /
• v.25 no.6
• /
• pp.111-121
• /
• 2014

The purpose of the study is to understand the unique characteristics of decoration style in traditional Javanese houses. Reviewing literature and visiting site were applied as the research method. Javanese House can be divided into three parts; roof, wall and floor. First, the roof of the traditional Javanese House is the most unique and important decorative element. The roofs are covered with roof-tiles and have clay carving ornaments on top. Usually there are no ceilings, just exposed to the oblique shape roof, which are made of wood to enable air ventilation. Joglo roof is the outstanding and representative roof type of Javanese houses. There is artistic and constructive roof structure named as tumpang sari in Joglo roof. The decoration on tumpang sari is the most colorful and symbolic ornaments. Secondly, the most unique element in the wall is the gebyok. Gebyok is made of wood and full of carved ornament, which has an artistic appearance, and also important function. The top part of doors are designed as perforated woodcarving, which give both aesthetic and ventilation purposes. Last, the stratified floor is begin with ground yard, then veranda that made from hardened clay, and main room constituted with a wood scaffold to provide air circulation and remove the humidity of the ground. The decorations of the column stand (umpak) are unique, where usually lotus flower is carved into black stone or lime stone. The outside of the buildings in Java Houses is not decorated by colors or symbols, whereas colors are only used in temples, pavilion or in royal housings. Instead they have carvings and decorations on important structural elements such as columns and beams inside. The ornaments and colors of decorations symbolize their god, ancestors and piece.

• Journal of the Korea Furniture Society
• /
• v.27 no.3
• /
• pp.211-219
• /
• 2016

Culture and design change with time and what they have in common is that both develop in line with the era's living environments. Today, various life styles have emerged to cause changes in housing and living modes and we are in need of designs that can be commonly used in any place. Under the circumstances, furniture plays a role of medium that helps interactions between the human and the space and it has long been used in a variety of ways amid the change of the times. Soban, Korean traditional furniture, is a tool used in our real life and it is a piece of furniture that caters for both arts and functionality. It has been more of a living necessity and accordingly carried wisdom of experience for survival, rather than artificial beauty. Unlike other types of furniture, it is a practical tool designed in consideration of users. Therefore, this study aims to find traditional furniture's wisdom of experience in Soban, which tends to get neglected, and ensure its value as a modern design element, and to contribute to express and study the formative arts of Korean design so that a past living necessity of Soban can overcome its limitation of being floor-seating furniture and become more than an eating tool in it value.

• (The)Study of the Eastern Classic
• /
• no.55
• /
• pp.265-291
• /
• 2014

Cheongeumrok is the journal of Gwonwoo(卷宇) Hong Chan-yu(1915-2005) during the period of January 9, 1969~January 14, 1982. He was personally involved in the foundation of a corporation called Yudohoi and also all of its operation, which makes him the most knowledgeable person about its history. His Cheongeumrok thus seems worthy enough as a proper material to arrange its history. Cheongeumrok consists of total 19 books, amounting to approximately 3,300 pieces of squared manuscript paper containing 200 letters per piece. He wrote it in Chinese and sometimes followed the Hangul-style word order while writing in Chinese. Many parts of the manuscript were written in a cursive hand with many Chinese poems embedded throughout it. The manuscript offers major information related to the corporation Yudohoi extracted from his journal. 1. There was a meeting of promoters to commemorate the foundation of the corporation in November, 1968, and it was in January, 1969 that it was established after getting a permit from the Ministry of Culture and Communication in January, 1969(Permit No. of Ministry of Culture and Communication: Da(다)-2-3(Jongmu(宗務)1732.5)). 2. Its office was moved from the original location of the 3rd floor of Wonnam Building, 133-1 Wonnam-dong, Jongro-gu, Seoul(currently Daekhak Pharmacy in front of Seoul National University Hospital) to Room 388 of Gwangjang Company, 4 Yeji-dong, Jongro-gu(office of Heungsan Social Gathering) and to second floor of KyungBo building, 21 Kyansu-dong, and to 3rd floor of Geongguk Building in Gyeongwoon-dong. 3. Its operational costs were covered by the supports of Seong Sang-yeong, the eldest son of Seong Jong-ho, the chairman of the board, later Kim Won-tae and Gwon Tae-hun, next chairmen of the board, and Hong Chan-yun, a director, since 1979. 4. His Confucian activities include participating in Seonggyungwan Seokjeonje (成均館 釋奠), joining in the erection of the Parijangseo(巴里長書) Monument and the publication of its commemorative poetry book, compiling the biographies(not completed) of Confucian patriotic martyrs for independence, and participating in the establishment of family rituals and regulations as a practice member. 5. His Yudohoi had a dispute with Seonggyungwan and lost a suit at the High Court in July, 1975 and Supreme Court in February, 1976. 6. There were discussions about its unification with Seonggyungwan Yudohoi, but there was hardly any progress. 7. Yudohoi started to provide full-scale courses on Confucian and Chinese classics under the leadership of Director Hong Chan-yu in 1979, and they have continued on today. Its courses for scholarship students including those for common citizens boast a history of 29 years and 220 graduates.