• KSTLE International Journal
• /
• 제1권1호
• /
• pp.12-20
• /
• 2000

Nano-wear and friction of carbon overcoated laser-textured and mechanically-textured computer hard disk were characterised after contact start/stop (CSS) wear test. Various analytical and mechanical testing techniques were employed to study the changes in topography, roughness, chemical elements, mechanical properties and friction characteristics of the coating arising from the contact start/stop wear test These techniques include: the atomic force microscopy (AFM), the continuous nano-indentation test, the nano-scratch test, the time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and the auger electron spectroscopy (AES). It was shown that the surface roughness of the laser-textured (LT) bump and mechanically textured (MT) Bone was reduced approximately am and 7nm, respectively, after the CSS wear test. The elastic modulus and hardness values increased after the CSS test, indicating straining hardening of the top coating layer, A critical load was also identified fer adhesion failure between the magnetic layer and the Ni-P layer, The TOF-SIMS analysis also revealed some reduction in the intensity of C and $C_2$$F_59$, confirming the wear of lubricant elements on the coating surface.

• 한국정밀공학회지
• /
• 제13권9호
• /
• pp.114-129
• /
• 1996

This paper describes the whole development phase for the underwater vehicle actuating system with high hydroload torque disturbance. This includes requirement analysis, system modeling, control algorithm design, real time implementation, test and performance evaluations. As for driving control algorithms, fuzzy logic, variable structure and PD(Proportional-Differential) algorithm were designed and implemented on board controller using a single chip microprocessor. Intel 8797. And test and performance evaluation is carried out both single test and wystem integration test. We could confirm the basic performance of actuating system through the single test and gereral developing work of any actuating systems was finished with a single performance test of actuating system without system integration test. But, we suggested that system integration test be needed. System integration test is carried out using G/C HILS(Guidance and Control Hardware-In-the -Loop Simulation) which is constituted flight motion simulator, load simulator, real time host computer and the related subsystems such as inertial navigation system, power supply system and Guidance and Control Computer etc.. The most important practical contribution of this paper is that full system characteristics such as minimal control effort, enhancement of guidance and autopilot performance by the actuating system using G/C HILS technique are investigated. Through full running G/C HILS, in spite of the passing to single tests, some control algorithm resulted in failure as to stability of full system and system time frame.

• 한국멀티미디어학회논문지
• /
• 제23권8호
• /
• pp.1075-1087
• /
• 2020

Aviation ICT technology is a convergence technology between aviation and electronics, and has a wide variety of applications, including navigation and education. Among them, in the field of aerial pilot training, there are many problems such as the possibility of accidents during training and the lack of coping skills for various situations. This raises the need for a simulated pilot training system similar to actual training. In this paper, pilot training data were collected in pilot training system using VR/AR to increase immersion in flight training, and Customized Pilot Training Platform with Collaborative Deep Learning in VR/AR Environment that can recommend effective training courses to pilots is proposed. To verify the accuracy of the recommendation, the performance of the proposed collaborative deep learning algorithm with the existing recommendation algorithm was evaluated, and the flight test score was measured based on the pilot's training data base, and the deviations of each result were compared. The proposed service platform can expect more reliable recommendation results than previous studies, and the user survey for verification showed high satisfaction.

• 한국항공우주학회지
• /
• 제30권7호
• /
• pp.144-149
• /
• 2002

본 논문은 항공전자 시스템 통제와 항법 및 사격통제, 커시브 및 라스터 그래픽 심볼 생성 둥의 기능이 통합된 항공전자시스템컴퓨터(ASC) 개발을 위한 실시간 다중 프로세서 병렬처리 기법을 제안한다. 4개의 32비트 RISC 프로세서간 논리적 계층구조는 마스터-슬레이브 다중 처리방식의 비대칭 구조를 가지며, Interaction 정도는 시분할 공통 시스템 버스와 공유 메모리 등을 활용한 밀 결합 방식을 채택하고, 효율적인 버스 중재방식을 고안하여 최적성능을 구현하였다. 일련의 비행시험을 통해 개발된 ASC를 검증하였으며, 전기적 시험과 환경 및 전자기 간섭 등 관련시험 또한 수행하였다.

• Journal of Electrical Engineering and Technology
• /
• 제7권4호
• /
• pp.615-625
• /
• 2012

GPS attitude outputs or carrier phase observables can be effectively utilized to compensate the attitude error of the strapdown inertial navigation system. However, when the integer ambiguity is not correctly resolved and/or a cycle slip occurs, an erroneous GPS output can be obtained. If the erroneous GPS output is applied to the attitude determination GPS/INS (ADGPS/INS) integrated navigation system, the performance of the system can be degraded. This paper proposes an ADGPS/INS integration system using the triple difference carrier phase observables. The proposed integration system contains a cycle slip detection algorithm, in which the inertial information is combined. Computer simulations and flight test were performed to verify effectiveness of the proposed navigation system. Results show that the proposed system gives an accurate and reliable navigation solution even when the integer ambiguity is not correctly resolved and the cycle slip occurs.

• International Journal of Aeronautical and Space Sciences
• /
• 제11권3호
• /
• pp.184-192
• /
• 2010

In this paper, an initial fine alignment algorithm, which is developed for the strap-down inertial navigation systems of satellite launch vehicles, is considered. For fast and accurate alignment, a simple closed-loop estimation algorithm using a proportional-integral controller is introduced. Through computer simulation for the sway condition in the launch pad, it is shown that a simple filter structure can guarantee fast computational speed that is adequate for real-time implementation as well as the required alignment accuracy and robustness. In addition, its implementation results are presented for the Naro-1 flight test.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권2호
• /
• pp.365-377
• /
• 2017

In this paper, we propose a method to identify the parameters of a rotorcraft slung load system using the modal characteristics of a flexible cable. The proposed method estimates the length of the cable and the mass of the payload by means of a frequency analysis. Dynamic equations of the slung load system with the flexible cable are derived using Udwadia-Kalaba equation (UKE) in order to build a simulation program, and the similarity of the simulated slung load movement is verified by comparison with flight test results. Using the computer simulation program, we show that the proposed method works well within various parameter ranges.

• 제어로봇시스템학회논문지
• /
• 제15권1호
• /
• pp.54-60
• /
• 2009

In this paper, a precision landing approach is implemented based on real-time image processing. A full-scale landmark for automatic landing is used. canny edge detection method is applied to identify the outside quadrilateral while circular hough transform is used for the recognition of inside circle. Position information on the ground landmark is uplinked to the unmanned helicopter via ground control computer in real time so that the unmanned helicopter control the air vehicle for accurate landing approach. Ground test and a couple of flight tests for autonomous landing approach show that the image processing and automatic landing operation system have good performance for the landing approach phase at the altitude of $20m{\sim}1m$ above ground level.

• 한국추진공학회지
• /
• 제8권2호
• /
• pp.73-84
• /
• 2004

로켓모터의 성능을 확인하기 위해 지상에서 연소시험을 수행하여 추력, 압력, 온도. 그리고 변형률 등 필요한 데이터를 계측하지만 측정된 추력은 시험대 동특성으로 인해 실제 추력과는 달리 과도진동이 포함된 왜곡된 형태를 나타낼 수 있다. 이러한 경우에는 추력 최대치나 추력 상승시간 등 로켓모터의 성능을 결정하는 값들의 정확한 값을 얻지 못할 수 있다. 따라서 본 논문에서는 이러한 추력 왜곡 현상의 원인을 분석하고 그 문제점을 해결하기 위한 이론적인 방법을 제안한다. 또한 제안된 방법을 가상 시험대에 적용하여 제안한 방법의 적용 가능성을 확인하고, 차후 실험 데이터를 이용한 추력 추정의 기본적인 방향을 제시하고자 한다.

• 한국항공우주학회지
• /
• 제48권4호
• /
• pp.303-310
• /
• 2020

본 논문은 무인항공기 전기시스템을 위한 전원모니터링장치에 대해서 기술하고 있으며, 무인항공기에 장착되는 AC/DC 발전기, 전원변환기, 배터리 및 기어박스의 데이터 측정과 임무장비의 전원 ON/OFF 장치를 운용하는 전원모니터링장치에 대한 설계를 기술하였다. 전원모니터링장치는 비행체 전원(발전기, 전원변환기 및 배터리)에 대한 전압과 전류를 측정하고, 기어박스의 압력과 온도를 측정하며, 임무컴퓨터로부터 수신된 임무장비의 전원명령을 수행한다. 전원모니터링장치는 무인항공기 비행체 요구사항을 만족하도록 설계하였으며, 구조/열 해석, 환경/EMI 및 지상/비행시험을 통하여 검증을 수행하였다.