• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.6
• /
• pp.581-588
• /
• 2015

In this paper, we researched that setting standard for RSC(Radar Cross Section) of naval surface ship could be determined and considered in various ways on ship's survivability, technical building feasibility, operation and so on. This study presented fundamental capacity on anti-ship missile, radar, flight and so no and the procedure to set of target/standards for RSC. The RCS standards is good at setting low as low as to improve survivability aspect, but because we should consider effect, technical limit, cost etc, this paper analyzed necessary elements to set standard than to suggest specific number and suggested procedure to set standars according to suggest the boundary of RCS.

• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.821-827
• /
• 2023

In this study, the aircraft technical standards of the Korea and the United States were analyzed to derive the dynamometer test procedure required to prove the compatibility for flight test certification of the metal brake pad for transport aircraft. Since the design modification of the brake systems is classified as a major change, the STC(Supplemental Type Certificate) and the PMA(Parts Manufacturer Approval) are required. In accordance with the TSO-C135a, the technical standard order for brake system in the United States, the design landing-stop test, accelerate-stop test, and most severe landing stop test were selected among the test items for flight test. The conditions for the dynamometer test are determined according to the specifications provided by aircraft manufacturer, and the brake pad condition, deceleration, and the number of test are defined according to the TSO-C135a.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.2
• /
• pp.27-33
• /
• 2014

There are several methods to improve the flight efficiency of HALE(High Altitude Long Endurance) UAV(Unmaned Aerial Vehicle). Airframe structural point of view, weight reduction of the airframe structure is the most important method to improve the flight efficiency. In order to reduce the weight of airframe structures, new concepts which are different from traditional airframe structure design such as the mylar wing skin should be introduced. The spar is the most important component in a mylar skin wing structure, so the spar weight reduction is the key point for reduction of the wing structural weight. In this study, design trade-off study for the front spar of the HALE UAV wing is conducted in order to reduce the weight. Design and analysis procedure of high aspect ratio wing spar are introduced. Several front spar structures are designed and trade-off study regarding the weight and strength for the each spar are performed. Spar design configurations are verified by the static strength test. Finally, optimal front spar design is decided and applied to the HALE UAV wing design.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.26 no.3
• /
• pp.87-92
• /
• 2018

This thesis is to provide procedures for documenting implementation performance and methodology of practical SMS enactment for Approved Training Organization(ATO). As an example, C flight training center, according MOLIT "Guidance on SMS Implementation", derived 32 implementation documents after writing the SMS manual to implement it. The 32 implementation documents are divided into 5 fields. In detail, they are (1) 2 documents on SMS Manual, (2) 7 documents on Safety policy and objectives (3) 3 documents on Safety risk management (4) 15 documents on Safety assurance (5) 5 documents on Safety promotion. By describing the documented performances according to these 32 implementation documents that was in use for 1 year in 2017, it is suggested that this procedure can be a methodology for practically enactment and implementing the SMS manual.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.6
• /
• pp.72-80
• /
• 2004

In this paper, the design procedure of a guidance algorithm in the boosting phase of missiles with free-flight after thrust cut-off is introduced. The purpose of the guidance is to achieve a required velocity vector at the thrust cut-off. Trajectory optimizations for four cost functions are performed to investigate implementable trajectories in the pitch plane. It is observed from the optimization results that high angle of attack maneuver in the beginning of the flight are required to satisfy the constraints. The proposed guidance algorithm consists of the pitch program to produce open-loop pitch attitude command and the yaw attitude command generator to nullify the velocity to go. The pitch program utilizes the pitch attitude histories obtained from the trajectory optimization.

• International Journal of Aeronautical and Space Sciences
• /
• v.11 no.2
• /
• pp.69-79
• /
• 2010

This paper describes the experimental framework for the control system design and validation of a rotorcraft unmanned aerial vehicle (UAV). Our approach follows the general procedure of nonlinear modeling, linear controller design, nonlinear simulation and flight test but uses an indoor-installed multi-camera system, which can provide full 6-degree of freedom (DOF) navigation information with high accuracy, to overcome the limitation of an outdoor flight experiment. In addition, a 3-DOF flying mill is used for the performance validation of the attitude control, which considers the characteristics of the multi-rotor type rotorcraft UAV. Our framework is applied to the design and mathematical modeling of the control system for a quad-rotor UAV, which was selected as the test-bed vehicle, and the controller design using the classical proportional-integral-derivative control method is explained. The experimental results showed that the proposed approach can be viewed as a successful tool in developing the controller of new rotorcraft UAVs with reduced cost and time.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.9 s.114
• /
• pp.926-936
• /
• 2006

In this study, structural vibration analyses of a smart unmanned aerial vehicle (UAV) have been conducted considering dynamic loads generated by rotating rotor and wakes. The present UAV (TR-S5-03) finite element model is constructed as a full three-dimensional configuration with different fuel conditions and tilting angles for helicopter, transition and airplane flight modes. Practical computational procedure for modal transient response analysis (MTRA) is established using general purpose finite element method (FEM) and computational fluid dynamics (CFD) technique. The dynamic loads generated by rotating blades in the transient and forward flight conditions are calculated by unsteady CFD technique with sliding mesh concept. As the results of present study, transient structural displacements and accelerations are presented in detail. In addition, vibration characteristics of structural parts and installed equipments are investigated for different fuel conditions and tilting angles.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.367-375
• /
• 2006

In this study, structural vibration analyses of a smart unmanned aerial vehicle (UAV) have been conducted considering dynamic loads generated by rotating rotor and wakes. The present UAV (TR-S5-03) finite element model is constructed as a full three-dimensional configuration with different fuel conditions and tilting angles for helicopter, transition and airplane flight modes. Practical computational procedure for modal transient response analysis (MTRA) is established. using general purpose finite element method (FEM) and computational fluid dynamics (CFD) technique. The dynamic loads generated by rotating blades in the transient and forward flight conditions are calculated by unsteady CFD technique with sliding mesh concept. As the results of present study, transient structural displacements and accelerations are presented in detail. In addition, vibration characteristics of structural parts and installed equipments are investigated for different fuel conditions and tilting angles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.3
• /
• pp.243-250
• /
• 2012

In this paper, a systematic consequence of evaluation method, procedure, and flight data analysis is investigated for application of ADS-33E-PRF to UAV. And it is applied to unmanned rotorcraft for evaluation. CNUHELI-020, which is developed in Chungnam National University, is used for assessment of handling quality: decoupled longitudinal and lateral/directional model were used to assess handling qualities. Evaluation flight maneuvers are categorized as hover/low-speed requirements, small-amplitude attitude change, and moderate-amplitude attitude change requirements.

• International Journal of Aeronautical and Space Sciences
• /
• v.9 no.2
• /
• pp.18-33
• /
• 2008

This paper presents design optimization of a new Active Twist Rotor (ATR) blade and conducts its aeroelastic analysis in forward flight condition. In order to improve a twist actuation performance, the present ATR blade utilizes a single crystal piezoelectric fiber composite actuator and the blade cross-sectional layout is designed through an optimization procedure. The single crystal piezoelectric fiber composite actuator has excellent piezoelectric strain performance when compared with the previous piezoelectric fiber composites such as Active Fiber Composites (AFC) and Macro Fiber Composites (MFC). Further design optimization gives a cross-sectional layout that maximizes the static twist actuation while satisfying various blade design requirements. After the design optimization is completed successfully, an aeroelastic analysis of the present ATR blade in forward flight is conducted to confirm the efficiency in reducing the vibratory loads at both fixed- and rotating-systems. Numerical simulation shows that the present ATR blade utilizing single crystal piezoelectric fiber composites may reduce the vibratory loads significantly even with much lower input-voltage when compared with that used in the previous ATR blade. However, for an application of the present single crystal piezoelectric actuator to a full scaled rotor blade, several issues exist. Difficulty of manufacturing in a large size and severe brittleness in its material characteristics will need to be examined.