• 한국도로학회논문집
• /
• 제11권4호
• /
• pp.107-115
• /
• 2009

본 연구는 포스트텐션 콘크리트 포장(PTCP: Post-Tensioned Concrete Pavement)의 슬래브 두께가 긴장 설계에 미치는 영향을 분석하여 PTCP에서 최적의 슬래브 두께를 선정하기 위하여 수행되었다. 먼저 슬래브 두께에 따른 차륜과 환경하중에 의한 인장응력을 유한요소해석 모델을 이용하여 구하였으며 허용 휨강도를 선정하여 긴장 응력을 산출하였다. 슬래브의 컬링을 야기하는 환경하중은 두께에 따라 동일한 온도구배 및 동일한 상하부 온도차의 두 가지 가정을 모두 고려하였다. 그리고 프리스트레싱을 위한 강선 긴장 시 긴장량의 손실을 고려하여 슬래브 두께 별로 긴장 설계를 수행하였다. 이러한 설계 결과를 비교 분석해 보면 일반적으로 슬래브 두께가 증가하면 강선의 개수도 따라서 증가되기 때문에 콘크리트와 강재 비용 모두가 증가하게 되어 비경제적인 설계가 된다. 환경하중의 영향이 미약하여 두께가 증가할 때 강선의 개수가 줄어드는 경우에도 두께 증가에 의한 비용이 강재 절감에 따른 비용보다 더 커지므로 두께가 증가할수록 경제적이지 못하다. 따라서 일반적으로 PTCP에서 슬래브 두께는 시공이 가능한 정도에서 최소로 유지하는 것이 타당하다고 할 수 있다.

• 한국지진공학회논문집
• /
• 제19권4호
• /
• pp.195-205
• /
• 2015

Various non-seismic tie details are frequently used for one- and two-story small buildings because the seismic demand on their deformation capacities is not relatively significant. To evaluate the effects of the non-seismic tie details on the seismic performance of reinforced concrete columns, six square columns with a cross section of $400{\times}400mm$ and six rectangular columns with a cross section of $250{\times}640mm$ were tested. The anchorage details at both ends and spacing of tie hoops, along with the cross-sectional shape and the magnitude of axial load, were considered as the primary test parameters. Test results showed that square columns had higher stiffness and lower lateral deformation rather than rectangular columns. Both lap spliced tie and U-shaped tie provided comparable or improved seismic performance to $90^{\circ}$ hook tie in terms of maximum strength, ductility, and energy dissipation. The predicted curves with modeling parameters in ASCE41-13 were conservative for test results of lap spliced tie and U-shaped tie specimens since plastic behavior after flexural yielding could not be considered. For economical design, ASCE41-13 should be revised with various test results of tie details.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권1호
• /
• pp.133-140
• /
• 2010

와이어로프와 T형 강판을 이용한 비부착공법의 내진성능을 평가하기 위해 중심 축하중과 반복 횡하중을 받는 5개의 보강된 기둥과 무보강 기둥을 실험하였다. 주요 변수는 T형 강판의 정착방법과 피복 모르터의 유 무이다. 실험결과 T형 강판이 정착된 기둥의 하중분배로 인한 휨 내력 및 연성 증가를 확인할 수 있었다. 그러나 T형 강판이 정착되지 않은 기둥은 연성 증가에는 효과적이지만 T형 강판으로 하중이 분배되지 않았다. 피복 모르터가 있는 보강된 기둥은 효과적인 초기 강성 및 휨 내력 증가를 보였지만 연성증가에는 불리하였다. 단면분할법을 이용해 예측한 보강된 기둥의 최대 휨 내력은 등가응력블럭을 사용하여 예측한 ACI 318-05 기준보다 실험결과를 예측하였다.

• 한국해양공학회지
• /
• 제21권6호
• /
• pp.7-15
• /
• 2007

A mechanical model was developed to predict the behavior of point-loaded RC slender beams (a/d > 2.5) without stirrups. It is commonly accepted by most researchers that a diagonal tension crack plays a predominant role in the failure mode of these beams, but the failure mechanism of these members is still debatable. In this paper, it was assumed that diagonal tension failure was triggered by the concrete cover splitting due to the dowel action at the initial location of diagonal tension cracks, which propagate from flexural cracks. When concrete cover splitting occurred, the shape of a diagonal tension crack was simultaneously developed, which can be determined from the principal tensile stress trajectory. This fictitious crack rotates onto the crack tip with load increase. During the rotation, all forces acting on the crack (i.e, dowel force of longitudinal bars, vertical component of concrete tensile force, shear force by aggregate interlock, shear force in compression zone) were calculated by considering the kinematical conditions such as crack width or sliding. These forces except for the shear force in the compression zone were uncoupled with respect to crack width and sliding by the proposed constitutive relations for friction along the crack. Uncoupling the shear forces along the crack was aimed at distinguishing each force from the total shear force and clarifying the failure mechanism of RC slender beams without stirrups. In addition, a proposed method deriving the dowel force of longitudinal bars made it possible to predict the secondary shear failure. The proposed model can be used to predict not only the entire behavior of point-loaded RC slender shear beams, but also the ultimate shear strength. The experiments used to validate the proposed model are reported in a companion paper.

• 한국전산구조공학회논문집
• /
• 제31권6호
• /
• pp.283-291
• /
• 2018

본 연구는 지진에 저항하는 부재인 비보강 조적벽체로 구성된 건물의 내진성능평가에 활용되는 비선형 정적해석을 위한 비보강 조적벽체의 해석모델을 수립하고자 하였다. 본 연구의 해석모델은 비보강 조적벽체의 휨거동을 모사하기 위한 파이버 요소와 비보강 조적벽체의 전단에 대한 응답을 예측하기 위한 전단스프링 요소로 구성된다. 본 논문은 먼저 제안하고 있는 모델의 형상에 대해서 설명하고, 기존에 행해진 조적조 프리즘의 실험결과로부터 얻은 응력-변형률 곡선을 근거로 파이버와 전단스프링 요소의 물성치에 대한 결정 방법을 설명한다. 제시하고 있는 모델은 비선형 정적 해석결과와 다른 연구자들에 의해 수행된 실험결과를 비교하여 타당성을 검증한다. 해당 모델은 최대강도, 초기강성, 그리고 이들로부터 얻어지는 비보강 조적벽체의 하중-변위 곡선을 적절하게 모사하고 있다. 또한, 해석모델이 비보강 조적벽체의 파괴모드를 예측할 수 있는 것으로 나타난다.

• 한국분말재료학회지
• /
• 제26권4호
• /
• pp.290-298
• /
• 2019

$TiO_2$-particles containing Co grains are fabricated via thermal hydrogenation and selective oxidation of TiCo alloy. For comparison, $TiO_2$-Co composite powders are prepared by two kinds of methods which were the mechanical carbonization and oxidation process, and the conventional mixing process. The microstructural characteristics of the prepared composites are analyzed by X-ray diffraction, field-emission scattering electron microscopy, and transmission electron microscopy. In addition, the composite powders are sintered at $800^{\circ}C$ by spark plasma sintering. The flexural strength and fracture toughness of the sintered samples prepared by thermal hydrogenation and mechanical carbonization are found to be higher than those of the samples prepared by the conventional mixing process. Moreover, the microstructures of sintered samples prepared by thermal hydrogenation and mechanical carbonization processes are found to be similar. The difference in the mechanical properties of sintered samples prepared by thermal hydrogenation and mechanical carbonization processes is attributed to the different sizes of metallic Co particles in the samples.

• 한국공간구조학회논문집
• /
• 제18권4호
• /
• pp.113-121
• /
• 2018

U-flanged truss beam is composed of u-shaped upper steel flange, lower steel plate of 8mm or more thickness, and connecting lattice bars. Upper flange and lower plate are connected by the diagonal lattice bars welded on the upper and lower sides. In this study the structural experiments on the U-flanged truss beams with various shapes of upper flange were performed, and the flexural and shear capacities of U-flanged truss beam in the construction stage were evaluated. The principal test parameters were the shape of upper flange and the alignment space of diagonal lattice bars. In all the test specimens, the peak loads were determined by the buckling of lattice bar regardless of the upper flange shape. The test results have shown that the buckling of lattice bar is very important design factor and there is no need to reinforce the basic u-shaped upper flange. However, the early lattice buckling occurred in the truss beam with upper steel bars because of the insufficient strength and stiffness of upper chord, and the reinforcement in the upper chord is necessary. The formulae of Eurocode 3 (2005) have presented more exact evaluations of lattice buckling load than those of KBC 2016.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권2호
• /
• pp.122-129
• /
• 2019

콘크리트 구조물에서 균열은 수축, 수화열 및 외부하중 등에 의해 발생하는 불가피한 현상으로, 외부 유해인자를 콘크리트 내부로의 침투를 용이하게 하여 내구성을 크게 감소시킨다. 최근 스스로 균열을 치유하는 자기치유 콘크리트에 대한 연구가 활발히 수행되고 있다. 또한 콘크리트에 발생하는 균열을 제어하여, 그 성능을 극대화하기 위한 자기치유 섬유 보강 콘크리트의 연구가 수행되고 있다. 본 연구에서는 PVA 섬유를 혼입한 자기치유 모르타르를 제작하였다. PVA 섬유 혼입율에 따른 압축강도 및 휨 성능 평가를 수행하였다. 또한, 흡수율 실험을 통해 자기치유 성능평가를 수행하였으며, 시간에 따라 균열 폭의 감소로 흡수되는 수분의 양이 감소하는 것을 확인하였다. 자기치유 생성물 분석을 통해 PVA 섬유 혼입에 의해 탄산칼슘 침전이 더 유리한 것으로 확인되었다.

• Steel and Composite Structures
• /
• 제29권6호
• /
• pp.717-734
• /
• 2018

This paper presents the flexural performance of steel beam-to-column joints composed of hollow structural section beams and columns. A finite element (FE) model was developed incorporating geometrical and material nonlinearities to evaluate the behaviour of joints subjected to bending moments. The numerical outcomes were validated with experimental results and compared with EN1993-1-8. The demountability of the structure was discussed based on the tested specimen. A parametric analysis was carried out to investigate the effects of steel yield strength, end-plate thickness, beam thickness, column wall thickness, bolt diameter, number of bolts and location. Consequently, an analytical model was derived based on the component method to predict the moment-rotation relationships for the sub-assemblies with extended end-plates. The accuracy of the proposed model was calibrated by the experimental and numerical results. It is found that the FE model is fairly reliable to predict the initial stiffness and moment capacity of the joints, while EN1993-1-8 overestimates the initial stiffness extensively. The beam-to-column joints are shown to be demountable and reusable with a moment up to 53% of the ultimate moment capacity. The end-plate thickness and column wall thickness have a significant influence on the joint behaviour, and the layout of double bolt-rows in tension is recommended for joints with extended end-plates. The derived analytical model is capable of predicting the moment-rotation relationship of the structure.

• Steel and Composite Structures
• /
• 제31권4호
• /
• pp.373-385
• /
• 2019

This paper presents a useful in-plane structural analysis of low-rise blind-bolted composite frames with semi-rigid joints. Analytical models were used to predict the moment-rotation relationship of the composite beam-to-column flush endplate joints that produced accurate and reliable results. The comparisons of the analytical model with test results in terms of the moment-rotation response verified the robustness and reliability of the model. Abaqus software was adopted to conduct frame analysis considering the material and geometrical non-linearities. The flexural behaviour of the composite frames was studied by applying the lateral loads incorporating wind and earthquake actions according to the Australian standards. A wide variety of frames with a varied number of bays and storeys was analysed to determine the bending moment envelopes under different load combinations. The design models were finalized that met the strength and serviceability limit state criteria. The results from the frame analysis suggest that among lateral loads, wind loads are more critical in Australia as compared to the earthquake loads. However, gravity loads alone govern the design as maximum sagging and hogging moments in the frames are produced as a result of the load combination with dead and live loads alone. This study provides a preliminary analysis and general understanding of the behaviour of low rise, semi-continuous frames subjected to lateral load characteristics of wind and earthquake conditions in Australia that can be applied in engineering practice.