• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.121-127
• /
• 2003

The stiffness of a bushing in a suspension is extremely important for the overall performance of the suspension system. A new measurement system including the flexible jig was developed to measure the multi-directional stiffness of bushings. To overcome the disadvantage of building each individual jig for each type and size of a bushing, we designed the flexible jig which can accommodate numerous bushings of similar shapes and sizes. Upon using the novel design of the flexible jig in the industry, we could successfully measure the torsional and conical stiffness of many bushings and apply the data for the prediction and evaluation of the performance of a suspension system, which would assist designing the optimal suspension system.

• 대한기계학회논문집A
• /
• 제31권1호
• /
• pp.1-10
• /
• 2007

This paper presents a design guidance of jig/fixture for flexible manufacturing system based on the verification of a base assembly motion instability. In flexible assembly system, the base assembly needs to be maintained in its assembled state without being taken apart. This requires stability in motion while the base assembly is handled or tilted. Therefore, the instability of the base assembly motion should be considered when determining the guide line of designing jig/fixture by evaluating a degree of the motion instability of the base assembly. To derive the instability, first we inference collision free assembly directions by extracting separable directions for the mating parts and calculate the separability which gives informations as to how the parts can be easily separated. Using these results, we determine the instability evaluated by summing all the modified separabilities of each component part within base assembly.

• Design & Manufacturing
• /
• 제14권3호
• /
• pp.23-30
• /
• 2020

Laser Assisted Thermo-Compression Bonding (LATCB) has been proposed to improve the "chip tilt due to the difference in solder bump height" that occurs during the conventional semiconductor chip bonding process. The bonding module of the LATCB system has used a piezoelectric actuator to control the inclination of the compression jig on a micro scale, and the piezoelectric actuator has been directly coupled to the compression jig to minimize the assembly tolerance of the compression jig. However, this structure generates a lateral force in the piezoelectric actuator when the compression jig is tilted, and the stacked piezoelectric element vulnerable to the lateral force has a risk of failure. In this paper, the optimal design of the flexure hinge was performed to minimize the lateral force generated in the piezoelectric actuator when the compression jig is tilted by using the displacement difference of the piezoelectric actuator in the bonding module for LATCB. The design variables of the flexure hinge were defined as the hinge height, the minimum diameter, and the notch radius. And the effect of the change of each variable on the stress generated in the flexible hinge and the lateral force acting on the piezoelectric actuator was analyzed. Also, optimization was carried out using commercial structural analysis software. As a result, when the displacement difference between the piezoelectric actuators is the maximum (90um), the maximum stress generated in the flexible hinge is 11.5% of the elastic limit of the hinge material, and the lateral force acting on the piezoelectric actuator is less than 1N.

• Radiation Oncology Journal
• /
• 제7권2호
• /
• pp.299-303
• /
• 1989

Authors have developed highly reproducible calibration method for the Micro-Selectron HDR Ir-192 system (Nucletron, Motherland). The new jig has a 10cm radius circular hole in the $30cm{\times}30cm{\times}0.2cm$ acrylic plate, and 5F flexible bronchial tubes are attached around the hole. The source moves along the circle in the tubes and the ionization chamber is placed verticaly at the center of the circular hole (center of the jig). Dose distribution near the center was derived theoretically, and measured with the film dosimetry system. Theoretical calculation and measurement show the error margin below $0.1\%$ for 1mm or 2mm position deviation. We have measured at 12 and 24 points of circle with 1, 6, 11 and 21 second dwell time of source in order to calculate the activity of the source. Measurements have been repeated daily for 50 days. The accuracy and the reproducibility are below $1\%$ error margin. The half life of the source from our measurement is estimated $73.4\pm0.4$ days.

• Transactions on Electrical and Electronic Materials
• /
• 제4권2호
• /
• pp.10-14
• /
• 2003

Flexible displays such as plastic-based liquid crystal displays (LCDs) and organic light-emitting diode displays (OLEDDs) have been researched and developed at KETI since 1997. The plastic film substrate is very weak to heat and pressure compared to glass substrate, that its fabrication process is limited to 110$^{\circ}C$ and low pressure. The ITO films were deposited on the bare plastic film substrate by rf-magnetron sputtering. Moreover, in order to maintain uniform cell gap and pressure on the plastic film substrate, we utilized newly-invented jig and fabrication process. Electro-optical characteristics were better than or equivalent to those of typical glass LCDs though it is thinner, lighter-weight, and more robust than glass LCDs.

• 마이크로전자및패키징학회지
• /
• 제30권3호
• /
• pp.102-110
• /
• 2023

본 연구에서는 플렉서블 레이저 투과 용접 (flexible laser transmission welding, f-LTW)을 이용한 박형 기판의 사면 접합 (scarf welding) 공정을 개발하였다. 플렉서블 응용을 위해 경사면의 기울기에 따른 인장 강도의 거동을 조사하였다. 박형 기판으로써 100 ㎛ 이하 두께의 플라스틱 기판이 사용되었으며, 사면 접합을 위해서 기판의 말단에 경사면을 형성하는 지그 장치를 개발하였다. 플렉서블 고분자 기판에 대한 경사면 맞대기 접합을 개발함으로써 공정 후 접합부 두께가 증가하지 않는 유연 접합 기술 개발에 성공하였다. 단축 인장시험을 통해 접합부의 인장 강도를 평가하였으며, 그 결과 경사면의 기울기가 완만할수록 인장 강도가 증가함을 확인하였다. 경사각에 따른 접합 계면에서의 응력 분석을 수행하여 접합 구조 설계 인자를 규명하였다. 본 결과는 동일한 공정 조건에서 접합부의 형상에 따라서 인장 강도가 크게 달라질 수 있음을 시사하므로 접합 공정에서 접합부 형상을 고려하는 것에 대한 중요성을 확인할 수 있다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2007년도 춘계종합학술대회
• /
• pp.540-543
• /
• 2007

본 논문에서는 모바일 TFT-LCD 모듈에서 발생하는 가청잡음을 감소시키기 위한 새로운 방법을 제안한다. 또한 가청잡음에 영향을 미치는 중요 인자들을 분석하였다. 이러한 잡음원은 FPCB와 LCD 패널간의 진동 및 윈도우와 백라이트에 충전되어 있던 정전기와 같은 다양한 중요 인자들로부터 유래됨을 확인하였다. 윈도우에 충전되어 있던 정전기로 인한 잡음 수준을 분석하기 위해 윈도우가 없는 LCD 모듈과 윈도우가 있는 LCD 모듈이 동시에 평가되었다. 신뢰감이 있고 재현성이 있는 데이터를 확보하기 위해 테스트 지그 및 측정시스템을 구축하였다.