• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.56-59
• /
• 1988

The main purpose of Set-up control of hot strip mill plant is to obtain the most regular thickness. Then the learning or adaptive computer control in hot strip rolling mill has been developed. But it is very difficult to keep the inter-stands load distribution ratio uniform; so that the deviation of strip flatness is not avoidable. This leads to the degradation of quality of the products. In this report, an improved method base on the steepest descent method including the computation of optimum step size. This method is applied to the off-line simulation. In consequence, the better balances of inter-stands load distribution is achieved in addition to improvements of output thickness of hot strip mill in POSCO.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.213-224
• /
• 2010

In this paper, we propose an algorithm both geometric correction using a grid point image and radiometric adaptive projection that dependent upon the luminance of the input image and that of the background. This method projects and captures the grid point image then calculates the geometrically corrected position by difference between the two images. Next, to compensate color, a corrected image is calculated by the ratio divided luminance of an input image by luminance of arbitrary surface. In addition, we found the scaling factor which controls the contrast to avoid clipping error. At this time, the scaling factor is dependent on mean image lightness when background is determined. Experimental results show that the proposed method achieves good performance and is able to reduce the perceived color clipping and artifacts, better approximating the projection on a white screen.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.3
• /
• pp.370-376
• /
• 2011

Recently, the application range of plastic gears is widely expanding by the development of engineering plastics with good mechanical properties. Plastic gears have excellent performances such as light weight, water resistance and vibration absorbing ability for metallic gears. In this study, the optimization of injection molding process was done for the large disk type plastic gears of auto phoropter. Design Of Experiment (Taguchi method) was adopted to find a tendency of molding conditions that influence the flatness of disk type gear. Four main factors for molding conditions were selected based on injection temperature, filling time, packing pressure and mold temperature. Also, Filling, packing and cooling analyses were carried out to evaluate Z directional deflection of large disk type gear by using the simulation software (Moldflow) based on the DOE. From the results, it was found that the injection temperature and packing pressure are the most sensitive parameters for the Z directional deflection of large disk type gears.

• Journal of the Korean Society of Costume
• /
• v.42
• /
• pp.127-136
• /
• 1999

This study purport to establish the size was flexibly receptive to consumers. Sample size was 6555 women in their 20's and 29 variables from the diret anthropometric data were applied to analyze. The preliminary survey was taken from Febraury 10. 1997 to May 23 1997 and the measurement was done from April 14, 1997 to June 10. 1997. Follwing the KS regulations Hanbok were given 3cm intervals each for the bust and hip girth and cm for th height. Size system was presented for the usage of developing the pattern of hanbok by analyzing the result of the regression coefficient and referring to the distribution chart of the back length and the neck to ulnar styloid length. When establishing the standard size for the ready-made Hanbok like Western style clothes it's convenient for both consumer and producer to present both bust girth and height. To enhance the fitting of Chogori we used the flatness ratio of bust as the reference for grouping styles of body. in the case of Chima-\ulcorner해갸 4 brackets are developed. First step was bust girth 78cm height 15cm second was bust girth 5852cm5 height 160cm third was bust girth 82cm height 165cm fourth was bust girth 88cm height 16cm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1028-1039
• /
• 1996

This study was focused on the examination of the flame structure and the combustion characteristics of diffusion flame which was formed the turbulent shear flow of a double coaxial air jet system. The shear flow was formed by the difference velocity of surrounding air jet(U$\_$s/) and center air jet (U$\_$c/). So experimental condition was divided S-type flame (.lambda. > 1) and C-type flame (.lambda. < 1) by velocity ratio .lambda. (=U$\_$s//U$\_$c/). For examination of the flame structure and the combustion characteristics in diffusion flame, coherent structure was observed in flame by schlieren photograph method. We measured fluctuating temperature and ion current simultaneously and accomplished the statistical analysis of its. According to schlieren photograph, the flame was stabilized in the rim of the direction of lower velocity air jet, coherent eddy was produced and developed by higher velocity air jet. The statistical data of fluctuating temperature and ion current was indicated that reaction was dominated by higher velocity air jet. The mixing state of burnt gas and non-burnt gas was distributed the wide area at Z = 100 mm of C-type flame.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.2
• /
• pp.1-6
• /
• 2008

In recent years, developments in the semiconductor and electronic industries have brought a rapid increase in the use of large size silicon wafer. For further improvement of the ultra precision surface and flatness of Si wafer necessary to high density ULSI, it is known that polishing is very important. However, most of these investigation was experiment less than 300mm diameter. Polishing is one of the important methods in manufacturing of Si wafers and in thinning of completed device wafers. This study reports the machining variables that has major influence on the characteristic of wafer polishing. It was adapted to polishing pressure, machining speed, and the slurry mix ratio, the optimum condition is selected by ultra precision wafer polishing using load cell and infrared temperature sensor. The optimum machining condition is selected a result data that use a pressure and table speed data. By using optimum condition, it achieves a ultra precision mirror like surface.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.8 no.1
• /
• pp.1-16
• /
• 1971

Ship hulls obtained by the streamline tracing method usually have characteristically drooped keel lines at the bottom, and a flattening of these bottoms would contribute considerably in utilizing these analytically obtainable hull forms in practical usage. In this dissertation, the author deals with a study on the determination of a practical hull form by the streamline tracing method with a particular emphasis on the bottom flattening problem. Investigations are centered around the form and the terms of bottom doublet distribution. Several examples are computed by varying bottom doublet sheet systematically while the main side source distribution is kept the same. The following conclusions are obtained based on those computed results: after the strength of a bottom doublet sheet can be determined more easily and efficiently by employing the concept of a control plane. If the distance from the distributed plane of the bottom doublet sheet to the control plane is defined as the control distance, the strength of the bottom doublet sheet, the flatness of traced lines, and the increment of the beam length ratio by adding the bottom doublet sheet are all related to the control distance by linear equations near the design bottom. It is observed that a better result can be obtained by using a "line-sampling method" for ${\zeta}_K>2T/L$, and a "plane-sampling method" for ${\zeta}_K{\leq}2T/L$, provided that the check points are sampled in the range ${\xi}{\leq}0.7$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.3
• /
• pp.101-110
• /
• 1998

The change of hydrogen storage characteristics by substituting zirconium for a portion of titanium in Ti-Cr-V alloys has been studied. The zirconium substitution decreased the plateau pressure and hysteresis of the PC isotherm. However, it decreased the hydrogen storage capacity and increased slopping in PC isotherm by forming $Cr_2Zr$ phase. By modifying the composition ratio of titanium to chromium, thereby suppressing the formation of $Cr_2Zr$ phase, we got an alloy having very high hydrogen storage capacity. The heat treatment of the alloys improved the flatness of plateau very much without a decrease in the maximum and the effective hydrogen storage capacities.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.979-983
• /
• 2007

In this thesis, a strip layout drawing of LCD S/C (shield case) was prepared. In the press die, strip layout drawing is a major factor that decides the mass production of a product. The 3D CAD/CAM system was applied for the easy correction of the interference factor with other parts to be mounted. The material use ratio was enhanced to 60.17% by optimizing the blank layout and strip layout in double width array. Furthermore, the flatness of the product was made to fit the requirements by adding the bidding process intensively on the notching part where the occurrence of the change in shape is expected owing to the thin material. For the 3D CAD/CAM software, Unigraphics NX3.0 was used. The strip layout drawing was prepared in 12 processes.

• Fashion & Textile Research Journal
• /
• v.19 no.1
• /
• pp.49-60
• /
• 2017

In this study, change trends and specific times for change in body size were sought to be identified by using manual measurements for Korean adult women at 20 to 89 of age, along with examinations of change trends and specific times of change in body shape based on body index values. The examinations of means, deviations, and variation coefficients revealed that there was a tendency of most height related measures to decrease. In addition, combined with decrease in height, growth in weight led to increased BMI, thus resulting in increase in measures of circumference, thickness, and breadth in the torso area. The BMI trends showed that with increasing age, BMI increased, reaching the peak between the ages of 55 and 59 and then decreasing from 64 of age, with the steepest increase in BMI at ages from 50 to 54. The examination of differences in the body flatness ratio for different parts of body found that with increasing age the ratio decreased, indicating a tendency for gradual change to round body shapes. The analysis of 3D body shape found that there were more back-bends and lowered shoulder levels with age, accompanied with a tendency for more bended legs and more inclined-forward necks. The key trends in changes in body measurements by age and detailed estimates of 3D standard body shape drawn out from this study are expected to significantly contribute to establishing a basic database for generating patterns reflecting age features of Korean adult females.