• 대한정형도수물리치료학회지
• /
• 제5권1호
• /
• pp.39-51
• /
• 1999

Background and Purpose. Objective measurements of hamstring muscle length are needed to quantify baseline limitations and to document the effectiveness of therapeutic interventions. Several indirect clinical tests for measuring hamstring muscle length are available, but influence of their test procedure is not well documented. The purpose of this study were 1) to describe hamstring muscle length as reflected by use of six tests(active straight leg raising(ASLR), passive straight leg raising(PSLR), passive straight leg raising with the lower back flat(PSLRB), active knee extension(AKE), passive knee extension(PKE), hip joint angle(HJA). 2) to examine the correlation among the tests. Subjects, Sixty subjects(30 men. 30 women) ranging in age from 18 to 25 years(mean 20.2 years) and with no limitation hamstring flexibility and no neurological and orthopedical problems. Methods. All subjects performed six tests. A inclinometer was used to determine the end point of range of motion. HJA was measured using an inclinometer placed over the sacrum. PSLRB were tested PSLR with the low back flat and the opposite thigh slightly flexed and support on pillows. Results, A mean ASLR value of 85.9 degrees, PSLR value of 99.9 degrees, PSLRB value of 109.8 degrees, AKE value of 77.2 degrees PKE value of 83.1 degrees and HJA value of 73.0 degrees were obtained for all subjects. A dependent t-test showed significant difference between the angles of ASLR and PSLR(p<0.001). There was a significant difference between the angles of PSLR and PSLRB(p<0.001). There was a significant difference between the angles of AKE and PKE(p<0.001). The highest correlation was between PSLR and PSLRB(r=0.915, p<0.001). All SLR tests were significants related(p<0.001), as well as AKE and PKE(p<0.001). The lowest correlation was between PKE and HJA(r=0.171. p>0.05). Conclusion and Discussion. The results indicated that the hip flexion angles for ASLR, PSLR and PSLRB were a difference, and the knee extension angles for AKE and PKE were a difference.

• 패션비즈니스
• /
• 제15권4호
• /
• pp.122-134
• /
• 2011

The peanut-shaped cloth diaper has cut uncomfortable crotch region off the square-shaped cloth diaper into a peanut-shape, and finished the edge by bias with multi-layers of fabric. This study has the purpose on providing the basic data for designing the peanut-shaped cloth diaper. For this purpose, the peanut-shaped cloth diapers on market were collected and analyzed by their shape and size, and also the patterns and differences in making were compared. 26 products from 17 brands were collected as samples. The analysis factors are the shape and size of the peanut-shaped cloth diaper, and characteristics and patterns in making. Among the samples, only 3 diapers were straight-shaped; the rest of them were peanut-shaped. The size difference between the big and small peanut-shaped cloth diapers was very large; the total length of the small one was 36.5cm-39cm which was very common, and the total length of the big one was more than 44cm. All diapers had longer width in the back than the front. The width of the front and back was different for each sample, therefore, it seemed to have some difficulties to set the standard. The peanut-shaped cloth diaper had different make-up depending on its characteristics including. absorbance, washing and drying. It was usually made by cotton woven of diamond jacquard or knit, and finished the edge by woven bias or knit bias. The peanut-shaped cloth diapers were various including a sheet of diaper, two sheets of diapers fixed with velcro, three sheets of diapers, and etc. For the patterns of the diapers, only two samples out of all had three dimensional shape, and the rest were produced using flat shape. There were no distinction between the diapers of girls and boys. Therefore, it is necessary to make the product based on scientific data about the peanut-shaped cloth diaper.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.190-194
• /
• 2006

This research investigates vehicle structure acceleration and vehicle deformation with RCAR crash test. To investigate vehicle damage characteristics in an individual case, it is possible to RCAR low speed crash test. In this study, two tests were conducted to evaluate difference between RCAR new condition and RCAR old condition. A two large vehicles were subjected to a frontal crash test at a speed of 15km/h with an offset of 40% $10^{\circ}$ angle barrier and flat barrier. The results of the 15km/h with an offset of 40% $10^{\circ}$ angle barrier revealed high acceleration value on the vehicle structure and high repair cost compared to the RCAR 15km/h with an offset of 40% flat barrier. So in order to improve damage characteristics in low speed crash of vehicle structure and body component of the monocoque type passenger vehicles, the end of front side member and front back beam should be designed with optimum level and to supply the end of front side member as a partial condition approx 300mm.

• 한국통신학회논문지
• /
• 제30권8A호
• /
• pp.688-696
• /
• 2005

본 논문에서는 위성을 이용한 디지털 위성방송 시스템에 적용하기 위한 고효율 평면안테나를 설계 및 제작하였다. 전통적인 접시형 안테나에 비하여 높은 개구효율, 용11한 설치 및 미려한 외관 등의 장점을 가지고 있는 평면 안테나를 설계하였다. 안테나 소자의 설계에는 마이크로스트립을 이용한 Annular Ring 공진기를 이용하였으며, 방사형 도파관을 이용한 급전구조를 채택하였다. 또한 수신신호를 중간주파 신호로 변환하기 위한 LNB를 안테나의 뒷면에 설치함으로써 전송손실의 최소화를 꾀하였다. 제작된 안테나는 직경 35cm, 이득은 31.8dBi 이며 개구효율은 약 $80\%$이다.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.132-143
• /
• 1992

This paper presents a method in order to calculate the vortex distribution, the streak-line and the time-line around the flat and the cambered otter board in two dimensional flow using the discrete vortex method, and to calculate C sub(L) and C sub(D) of the otter boards varied with the passage of time by the numerical simulation using the Blasu's formula. The results obtained are summarized as follows: 1. Flow pattern around the otter boards calculated by the discrete vortex method was resembled closely that of the visualized photograph. 2. C sub(L) and C sub(D) calculated by the numerical simulation was very similar to the model test. 3. The circulation direction around the otter boards and the action direction of the shearing force can be recognized from the time-line around the otter boards. 4. Flow speed in the back side of the otter boards was faster than that in the front side, and the difference of the flow speed in both side of the cambered otter boards was about 1.3 times greater than that of the flat otter boards. 5. The clockwise vortex was generated in the trailing edge, and the counter-clockwise vortex was generated the leading edge of the otter boards. And they were shown the shape of Karman's vortex varied with the passage of time.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.54-60
• /
• 2015

Laser-arc hybrid welding has been considered as an effective pipe girth welding process since early 2000's. Tolerance for fit-up offsets such as gap and edge misalignment is one of most important requirements in pipe girth laser-arc hybrid welding, and several approaches using parameter optimization, a laser beam scanning and an arc oscillation have been tried. However the required offset tolerance has not been fully accomplished up to now and laser-arc hybrid welding has not been widely applied in pipeline construction than expected, despite of its high welding speed and deep penetration. In this study, internal welding was adopted to ensure the offset tolerance and sound back bead. The effect of welding parameters on bead shape was investigated at the flat position. Also tolerances for gap and edge misalignment were verified as 0.5 mm and 2.0 mm, respectively. The position welding trials were conducted at several welding positions from the flat to the overhead position in a downward direction. With the fixed welding speed, arc current for gas metal arc welding current and laser output power, adequate welding voltages for gas metal arc welding were suggested for each position.

• 한국의류학회지
• /
• 제20권2호
• /
• pp.257-269
• /
• 1996

The puropose of this study was to investigate the movement-fitness according to the surface changing of lower limb The experimental items were divided into the lower limb movements (5) and body-shapes (7). This study was done by the expansion and contraction rate consideration of length, girth Also, the lower half of body shape-change on the movements and body-shapes by flat shell was done simultaneously. The summarized findings resulted from experiments and investigation are suggested as follows; First, when commpared the expansion and contraction rate of the length and girth items, the expansion rate of the back crotch length (14~20%), hip girth (10~ 21%) and knee girth (6.2~18.5%) in rabbit leap movement was the most notable among all variables considered in this experimentation. On the others hand, the front croth length (-22~-52%) contracted remarkably. And big-thigh type was the most notable on the body-shape comparision. Second, in comparision of the expansion and contraction rate of the area on the blocks, the expansion of the hip (50~200%) and knee (51~74%) block was the most remarkable. Especially, in the sit on knees movement of the hip-down type expanded 209.4%. Third, in comparision of the lower half of body shape-change, on the movements and body- shapes by the flat shell, under the influence of knee-joint and hip-joint the shape-changs of the hip and knee block was the most notable. But the shape-change of the waist, abdomen, calf, and ankle was feeble.

• 대한전자공학회논문지TE
• /
• 제37권1호
• /
• pp.12-17
• /
• 2000

본 논문은 가스의 방전 현상으로부터 발생되는 자외선을 이용하는 평판 형광 램프의 주파수 특성에 대하여 연구하였다. 램프는 절연층, 형광층, 가스층으로 구성된다. 램프의 특성에서 불꽃 전압과 휘도 균일 전압은 주파수의 증가에 따라 감소하였다. 이것은 가스 갭내에서의 공간 전하 효과로 설명이 가능하였다. FFL의 휘도는 700Vrms, 80 kHz의 구동 조건에서 2700cd/$m^2$ 을 얻었으며, 최대 휘도 효율은 5 lm/W를 보였다.

• 한국의류학회지
• /
• 제27권6호
• /
• pp.624-634
• /
• 2003

The purpose of this study was to classify body types of elderly male aged between 60 and 80. 40 direct items and 22 indexes were measured. The result were as follows. First. through the factor analysis of indexes, 8 factors were extracted upon factor scores, 4 clusters represented characteristics of elderly male's body type. Type 1 indicates flat and bend-forward type. Type 2 indicates fat and bend-forward type. Type 3 indicates lean-back type and is a little bit fat and the waist is round. Type 4 indicates a straight type in which the chest and the hip are developed. Second, drop was needed to discriminate elderly male's body type. 3 types of drop were extracted. The body type with big drop is Y type in which the drop distance is between 14 and 22cm. The body type with standard drop is A type in which the drop distance is between 6 and 14cm. The body type with small drop is B type in which the drop distance is between -4 and 6cm. Third, when the types of appearance rate were combined, 7 body types of elderly male showed high appearance rate; A1, B1, A2, B2, A3, A4, B4. According to the above result, flat and bended-forward type with drop A was dominant body type of elderly male.

• 한국재료학회지
• /
• 제20권10호
• /
• pp.501-507
• /
• 2010

Changes in surface morphology and roughness of dc sputtered ZnO:Al/Ag back reflectors by varying the deposition temperature and their influence on the performance of flexible silicon thin film solar cells were systematically investigated. By increasing the deposition temperature from $25^{\circ}C$ to $500^{\circ}C$, the grain size of Ag thin films increased from 100 nm to 1000 nm and the grain size distribution became irregular, which resulted in an increment of surface roughness from 6.6 nm to 46.6 nm. Even after the 100 nm thick ZnO:Al film deposition, the surface morphology and roughness of the ZnO:Al/Ag double structured back reflectors were the same as those of the Ag layers, meaning that the ZnO:Al films were deposited conformally on the Ag films without unnecessary changes in the surfacefeatures. The diffused reflectance of the back reflectors improved significantly with the increasing grain size and surface roughness of the Ag films, and in particular, an enhanced diffused reflectance in the long wavelength over 800 nm was observed in the Ag back reflectors deposited at $500^{\circ}C$, which had an irregular grain size distribution of 200-1000 nm and large surface roughness. The improved light scattering properties on the rough ZnO:Al/Ag back reflector surfaces led to an increase of light trapping in the solar cells, and this resulted in a noticeable improvement in the $J_{sc}$ values from 9.94 mA/$cm^2$ for the flat Ag back reflector at $25^{\circ}C$ to 13.36 mA/$cm^2$ for the rough one at $500^{\circ}C$. A conversion efficiency of 7.60% ($V_{oc}$ = 0.93, $J_{sc}$ = 13.36 mA/$cm^2$, FF = 61%) was achieved in the flexible silicon thin film solar cells at this moment.