• Proceedings of the Korean Society of Veterinary Pathology Conference
• /
• 2002.11a
• /
• pp.81-85
• /
• 2002

Dogs are laid on their left sides (Puppies may be placed on their back). 1. Lift the right forelimb, insert the knife in the axillary region, and cut its muscular attachment to thorax. Reflect the limb dorsally until it lays flat on the table. 2. Lift the right hindlimb, cut the inguinal area skin and the adductor muscles, and disarticulate the coxofemoral joint. Reflect the limb dorsally until it lays flat on the table. 3. A midline skin incision is made from the symphysis of the mandible to the anus, circumventing the umbilicus and male external genitalia. (omitted)

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.781-782
• /
• 2006

This paper presents a drive strategy to reduce torque ripple of a permanent magnet Brushless DC Motor(BLDCM) with short $120^{\circ}$ flat top Back Electromotive Force(Back-EMF). In this strategy, the phase Back-EMF is divided into four sections. Then, in each section the phase current is regulated by corresponding PWM duty ratio to compensatethe torque ripple caused by imperfect Back-EMF. A program based on this strategy has been implemented in MATLAB@Simulink. The validity of the presented method is verified by simulation results.

• Proceedings of the ESK Conference
• /
• 1997.10a
• /
• pp.40-55
• /
• 1997

The purpose of this study are to examine the characters of the lower half body shape in the middle aged women and to make slacks patttern on the base of four difference body shapes as follows. The lower half body shapes were classified into 4 types on the basis of their lateral view silhouette, whose characters were summarized as followings. (1) "Type 1" meant the right body shape with the standard protrusion of abdomen and hips. (2) "Type 2" showed the body shape with prominent hips, which had the flat abdominal silhouette and the greatly curved hips silhouette. (3) "Type 3" was the body shape with the prominent abdomen and the flat hips, in which the frontal view silhouette of the abdomen was greatly curved and the rear view silhouette of hips is less curved. (4) "Type 4" was characterized with prominent abdomen and hips. The slaks patterns were based on the lower half body shape characters and resulted in followings. (1) In the type 1, little difference from conventional patterns was seen in experiment pattern, in which the front waist girth was W/4{\times}0.5cm+0.5cm+fold(2.5cm) and the back waist girth W/4+0.5cm-0.5cm+dart(3.5cm). The front hip girth was defined as H/4+2.0cm+0.5cm and the back hip girth as H/4+2.0cm-0.5cm due to its increased ease amount produced by abdominal fat deposition. (2) In the type 2 experimental pattern, the front and back differences of the waist girth and the hip girth were defined as 1.0cm and 2.0cm separately. Accordingly, the front waist girth was W/4+0.5cm+ 1.0cm+fold(2.0cm), the back waist girth W/4+0.5cm-1.0cm+dart(6.5cm), the front hip girth H/4+2.0cm+1.0cm and the back hip girth H/4+2.0cm-1.0cm. (3) In type 3, the front waist girth was set up as W/4+0.5cm+0.5cm+fold (4.5cm) for the increased front fold amount and the back waist girth was W/4+0.5cm+0.5cm+dart(3.0cm). The front hip girth was made as H/4+2.5cm+0.5cm and the back hip girth H/4+2.5cm-0.5cm. (4) In type 4, considered were $\circled1$ the increased fornt fold amount due to the abdonimal protrusion, $\circled2$ the increased back dart amount and the decreased back dart length owing to the hips prominent and $\circled3$ the front and back differences of waist and hip girth for the lateral view silhouette. Therefore the front waist girth was defined as W/4+0.5cm+2.0cm+flod (5.0cm), the back waist girth as W/4+0.5cm-20.cm+dart(4.0cm), the front hip girth as H/4+2.0cm+1.0cm and the back hip girth as H/4+2.0cm-1.0cm. The sensory evaluation of appearance and comfort was appeared more suitable on the experiment pattern than on the conventional pattern.

• The Research Journal of the Costume Culture
• /
• v.16 no.5
• /
• pp.852-862
• /
• 2008

The purpose of this paper is to find how to do the width of skirt and the girth of the waist in the adequate pattern making for the obese women's skirt. Appearance test of the five experimental skirts was evaluated by the four experts in clothing construction. At the same time, 3D clothing air volume was observed for the five types of experimental skirt with different size specifications. The results from the appearance test were as follows; when the width of skirt pattern is set for(the shell girth/2), it was suggested w/4+1(front), w/4(back) for girth of the waist. On one hand, in case of (the shell girth of front)/2+(the shell girth of back)/2, it was suggested(the waist girth of front)/2 and(waist girth of back)/2 for obese women's skirt with the best appearance. As results, it was found that the width of skirt pattern for the obese women should be the greatest shell girth instead of hip girth. In the case of the hip girth, the amount of ease on hip was suggested 6cm. It was found that pattern with the wrinkle of ease was full of the gaps between body and skirt in 3D clothing air volume. In spreading out to 2D flat pattern from 3D scan data, when the width of skirt pattern was set for(the shell girth of front)/2+(the shell girth of back)/2, it was suggested(the waist girth of front/2)+(the waist girth of back/2) than the shell girth/2 in girth of the waist for the best appearance. And the conversion of 3D scan data into 2D flat pattern in curve shape of crosswise had to spread out of the plane in straight line. The obese women's clothing should be manufactured with systematical consideration of the diversity and scarcity of the obese women's body shape.

• The International Journal of Costume Culture
• /
• v.2 no.2
• /
• pp.80-96
• /
• 1999

This research focused on pattern adjustments of the stable knit garment for women. Fourteen different types of the knitted fabrics by 12 gauge, computerized flat bed machines were cut in as one half of the torso front, one half of the torso back, and one side of the sleeves for each of them. Guidelines such as the center front, the center back, the armhole, the bust-line, the waistline, the hip-line the hemline were basted on the torso patterns in the knitted fabrics. Also the grain-line, the elbow-line, and the hemline were basted on the one side of the sleeves in the same as above knitted fabrics. The torso patterns in the knitted fabrics were exhibited on the dress-forms on top of the torso patterns in Muslin, which also have the same guidelines drawn on. The distances between the guidelines on Muslin and those on the knitted fabrics for each set of the sample fabrics were measured every three days for two weeks. The fabric properties of the fourteen knitted fabrics such as fiber contents, stitch density both in the wale and course directions, weight, thickness, stretch & recovery, residual shrinkage, relaxation and drapability were laboratory tested for how these were related to finished appearance of 12 gauge, computerized flat knit garments and also in order to prove the fourteen knitted fabrics fall to a category of such as the stable knit. The results from the investigation revealed that six fabric properties such as stitch density, thickness, stretch recovery, residual shrinkage and relaxation were not so much significant factors as weight and drapability. In conclusion, fabric weight, and drapability of the fabric resulting from fiber contents were the cause of final appearance distortion of garment. When adapting patterns for stabilized, 12 gauge, computerized flat knitted fabrics, the fiber contents of the fabrics should be taken into consideration to reduce the production cost and produce better-fit garments.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.5 no.1
• /
• pp.31-50
• /
• 1997

A new variable wing that can be swept back and forward synchronously were developed to enhance the aerodynamic and stability characteristics of a high speed airplane. The configuration of the new variable wing changes in such a way that inner part of the wing sweeps forward and outer part of the wing sweeps backward, the shift of aerodynamic center of the wing is small, therfore the static margin that is required for the stability of a airplane is not affected. In this study, various configurations of wing models by combined swept back and forward were designed and a wind tunnel tests were conducted to investigate the aerodynamic characteristics of these variable wings. The experimental results showed that the variable wing by combined swept back and forward has no effect on the pitching moment coefficient affecting on an aircraft stability margin and enhance the aerodynamic characteristics for a given approach angle of attack.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.111-113
• /
• 2007

본 논문에서는 제논 유전체 장벽 방전형 평판형광램프용 Fly-Back방식 전자식 안정기를 설계하였다. 본 전자식 안정기는 Fly-Back방식의 능동형 역률 보상 회로와 인버터회로를 사용하여 기존의 Sine wave의 형태가 아닌 펄스파 형태의 출력을 만드는 고역률, 고신뢰성 전자식 안정기를 제작하였다. 제논 평판형광램프의 점등전압은 고압이 사용되므로 램프 파손의 경우와 무부하의 경우로부터 사고를 방지하기 위해 보호회로를 사용하여 이상전압, 이상전류에 의한 사고를 차단했다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.8
• /
• pp.1420-1431
• /
• 2001

This research was done to classify lower body types by direct measurements, side and back view types from waistline to gluteal furrow line individually, and to analyze correspondence these lower body types with side and back view types from waistline to gluteal furrow line. The subjects of this study were 191 female college students from 18 to 25 years old residing in Pusan urban area. Type 1(long and slim) of lower body types by direct measurements was correspond with Type 1(slim curve) and Type 4(slim and protrusive hip) of side view and Type 3(wide and curve) and Type 4(trapezoid shape) of back view. Type 2(short and thick) of lower body types was correspond with Type 3(thick and droopy hip) of side view and Type 1(wide and straight) of back view. Type 3(short and slim) of lower body types was correspond with Type 2(slim and flat hip) of side view and Type 2(narrow and curve) of back view.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.220-224
• /
• 2005

The technology trend of Flat Panel Display (FPD) equipments have been demanded that there are compact and multi-function. Therefore, nano/micro scale patterned on polymeric materials of Back Light Unit (BLU) in Liquid Crystal Display (LCD) that has been investigated. This paper describes a series of Horizontal Type Micro Tensile Tester that were carried out to investigate the load strain distance performance of typical polymeric material sheets. The polymeric materials film that micro size shaped specimens for tensile test are used by Cold-Isostatic-Press (CIP). Test equipment is Horizontal type Micro Tensile Tester that is presented to measure the micro scale mechanical property of thin film for FPD. This paper presents which easy testing tools measure for micro patterned on polyethylene (PET) specimens.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1519-1521
• /
• 2007

In this work, a coplanar-type plasma flat fluorescent lamp having cross type of electrode was fabricated by screen printing and sealing technique. Cross type of electrode with a dielectric layer were screen-printed on a rear glass plate, and then fired at $550^{\circ}C$. Phosphor was printed on and fired at $450^{\circ}C$. Finally, the lamp was sealed by frit glass at $450^{\circ}C$. The lamp of cross electrode type was studied depending on the electrode gap and the thickness of dielectric layer.