• Korean Journal of Geomatics
• /
• v.3 no.1
• /
• pp.43-51
• /
• 2003

This paper presents the benefits of using close-range digital photogrammetric techniques for measuring the roughness of rock surfaces, using digital stereo images obtained from a Rolleiflex 6006 metric camera. To precisely measure surface roughness, we researched on how to use the flat and curved reference surface obtained from geometrically corrected digital images of the rock surface by using the least squares method. To test the precision of the proposed technique, the surface roughness has been measured between the reference surface and sample areas of very smooth-surfaced rock. Then the results were compared with the measurements obtained from a laser sensor profilometer.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.3 s.20
• /
• pp.15-20
• /
• 2003

For measuring friction factor of artificially-roughened surfaces which are usually applied to damper seals, flat plate test apparatus is designed and fabricated. The measurements of leakage flow and pressure distribution through round-hole patterned specimen with different hole areas are described, and a method is discussed for determining the friction factor experimentally. Results show that the friction factor of the round-hole patterned surface is bigger than that of smooth surface, and increases as increasing the hole area. A empirical friction factor model for the round-hole patterned surface can be descrived by the Moody's friction factor formula.

• Tribology and Lubricants
• /
• v.17 no.3
• /
• pp.191-197
• /
• 2001

Nano adhesion and friction characteristics between SPM(scanning electron microscope) tips and flat plates of different materials were experimentally studied. Tests were performed to measure adhesion and friction in AFM(atomic force microscope) and LFM(lateral force microscope) modes in different conditions of relative humidity. Three different Si$_3$N$_4$ tips (rdaii : 15nm, 22nm and 50 nm) and three different flat plates of Si-wafer(100), W-DLC(tungsten-incorporated diamond-like carbon) and DLC were used. Results generally showed that adhesion and friction increased with the tip radius, and W-DLC and DLC surfaces were superior to Si-wafer. But the adhesion force of Si-wafer showed non linearity with the tip radius while W-DLC and DLC surfaces showed good correlation to the “JKR model”. It was found that high adhesion force between Si-wafer and a large radius of tip was caused by a capillary action due to the condensed water.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.251-259
• /
• 2010

It is presented in this study a new efficient intelligent machining strategy, which can be used to remove the uncut volume at the boundary region of curved surfaces caused by cutter interference. The geometric form definitions and recognition of topological features of the surface triangulation mesh are used to generate cutter paths along successive and interconnected steepest pathways, that minimize the cusp height left after flat end milling. In order to machine the uncut volume gradually, the z-map cutter centers are adjusted to avoid cutter interference for the 6 kinds of avoidance types. And then, the generative subsequent paths are sequenced to determine the second step cutter paths for the next uncut volume. For the 2 kinds of test models with convex and concave surface region, the implemented software algorithm is evaluated by investigating the residual swelling of uncut volume for each machining step.

• Journal of the Optical Society of Korea
• /
• v.18 no.2
• /
• pp.180-183
• /
• 2014

The surface of semiconductor solar cells, such as a-Si or CIGS (CuInGaSe) solar cells is not flat but textured in the microscopic domain. With textured surfaces, the optical reflectivity of a solar cell is different from that of flat surfaces in the wavelength region. In this paper, the effects of a textured surface on a CIGS solar cell are presented by RCWA (Rigorous Coupled Wave Analysis) method. The effect of incoherent light is also considered by RCWA with a Fourier analysis while conventional optical simulation uses the input light on the solar cell as coherent light. Using experimental results, the author showed that the RCWA method with a Fourier analysis is a proper method to simulate the optical properties of CIGS solar cells.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.773-776
• /
• 2005

An Experiment was carried out to study deburring in frilling hole on the Inclined exit surface. Two different deburring tools, exit surface angles, materials and cutting conditions were selected to check their performance using CNC machining center. In deburring operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quite different burr formation when comparing with flat surface. Deburring characteristics are analyzed according to the deburring tools and cutting conditions. Several strategies for a effective deburring on inclined exit surface were proposed.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.3
• /
• pp.190-201
• /
• 2002

Surfaces of many engineering structures, specially, those of ships and airplanes are commonly fabricated as doubly curved shapes as well as singly curved surfaces to fulfill functional requirements. Given a three dimensional design surface, the first step in the fabrication process is unfolding or planar development of this surfaces into a planar shape so that the manufacturer can determine the initial shape of the flat plate. Also a good planar development enables the manufacturer to estimate the strain distribution required to form the design shape. In this paper, an algorithm for optimal approximated development of a general curved surface, including both singly and doubly curved surface is developed in the sense that the strain energy from its planar development to the design surface is minimized, subjected to some constraints. The development process is formulated into a constrained nonlinear programming problem, which is on basis of deformation theory and finite element. Constraints are subjected to characteristics of the fabrication method. Some examples on typical surfaces and the practical ship surfaces show the effectiveness of this algorithm.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.3 no.1
• /
• pp.44-56
• /
• 2000

Through the ISODATA method of unsupervised classification, the micro-landform of Gomso-Bay tidal flat was classified into mud, mixed, and sand flats by using Landsat TM image. Each tidal flat shows on apparent differences in its topographical characteristics and grain size compositions. Mud flat is occupied the innermost part of the tidal flat. Sand flat is distributed adjacent to the entrance of the bay, while the mixed one is located in the central part of the bay. Mud flat deposits have fine grain size, more than 4 in average mean phi, bad sorting, more than 1 phi in standard devation, and positive skewness. Mixed and sand flat deposits have coarse grain size, less than 4 average mean phi, good sorting, less than 1 phi in standard daviation, and negative skewness. Topographically, the mud flat consists of flat surfaces and dissected channels. The average depth of dissected channels is about 2 meters. Meanwhile, sand flat has a very flat landform with well-developed ripple marks of less than 10 centimeters in average relief. And the mixed one shows the intermediate topographical characteristics of those of mud and sand flats.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2005.02a
• /
• pp.35-35
• /
• 2005

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2018.11a
• /
• pp.225-226
• /
• 2018