• Wind and Structures
• /
• v.17 no.5
• /
• pp.537-552
• /
• 2013

Wind tunnel experiments were performed to study the wind loads on an inclined flat plate with and without a guide plate. Highly turbulent flow, which corresponded to free-stream turbulence intensity on the flat roof of low-rise buildings, was produced by a turbulence generation grid at the inlet of the test section. The test model could represent a typical solar collector panel of a solar water heater. There are up-stream movements of the separation bubble and side-edge vortices, more intense fluctuating pressure and a higher bending moment in the turbulent flow. A guide plate would result in higher lift coefficient, particularly with an increased projected area ratio of a guide plate to an inclined flat plate. The value of lift coefficient is considerably lower with increased free-stream turbulent intensity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.9
• /
• pp.2139-2144
• /
• 2013

This paper has analyzed the possibility about implementation of the low-cost, high-efficiency tracking antenna using flat panel antenna. Tracking antenna is consisted of four flat-antenna, comparators, tracking receiver, controller. We analyzed input signal of antenna array about the magnitude and phase of radio wave. In addition, We suggested the available tracking range through the analysis of output signal. We have minimized the error rate that happened on two path through design two path of the azimuth and elevation. Analysis results has a tracking range of ${\pm}3$ degrees, it is possible to implement.

• The Journal of Information Systems
• /
• v.17 no.4
• /
• pp.301-319
• /
• 2008

The display market has been replaced by the FPD (Flat Panel Display) from the CRT (Cathode-Ray Tube) since the late 1990s. In the FPD production line, the most equipment has high price. Thus, when the equipment has multi-function, the repetitive process is arranged for the equipment. However, such disposition of equipment results in more complicated process flow owing to repetitive operations. This reduces the production capacity and increases lead-time in turn. In this paper, we develop an AutoMod simulation system that derives to information about the quantity, production lead-time, utilities of facilities, and occupation rates of racks. In this simulation system, we consider the situation where the equipment might be broken and suspended randomly. For the developed system, we first evaluate a production plan with current layout and then, propose a revised alternative plan. Using the same simulation scheme, we investigate comparing the production quantity and lead-time with the two plans. In addition, for a proposed alternative, we try to forecast the most adequate rule between the two job dispatching rules which are FOR (Fewest Operation Remaining) and FCFS (First Come First Serve) through simulation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.3
• /
• pp.100-109
• /
• 2022

In this study, calibration technology that increases the alignment accuracy in large flexible flat panels was studied. For precise of calibration, a systematization of the calibration algorithm was established, and a calibration correction technique was studied to revise calibration errors. A coordinate systems of camera and UVW stage was established to get the global position of the mark, and equations for translational and rotational calibration were systematically derived based on geometrical analysis. Correction process for the calibration data was carried, and alignment experiments were performed sequentially in cases of the presence or absence of calibration-correction. Alignment results of both calibration correction and non-calibration correction showed accuracy performance less than 1㎛. On the other hand, the standard deviation in calibration-correction is smaller than non-calibration correction. Therefore, calibration correction showed improvement of the alignment repeatability.

• Journal of Information Display
• /
• v.9 no.3
• /
• pp.8-11
• /
• 2008

A novel non-alkoxide sol-gel process for synthesizing Ga-doped ZnO thin film on glass was derived for possible use as a transparent electrode in flat-panel displays, using zinc acetate dehydrate as the starting material. The structural and electrical properties of thin films have been characterized as functions of Ga addition and post-heat-treatments. Their carrier density, Hall mobility, and optical transmittance were measured and discussed herein to explain the characteristics of the sol-gel-derived Ga-doped ZnO thin film on glass.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.335-338
• /
• 2004

In this study has developed analysis system for automatic inspection of FPD(Flat Panel Display) characteristic, such as brightness, view angle, color ratio in the manufacturing process. Developed system consists of inspection-sensor part, acquiring a data by 3-CCD Color CCD camera and Inspection-stage part, driving a FPD holder to rotation and tilt direction. In experiment results, we could have ensured easily brightness distribution, available view angle, color reproduce and could expect to improve the quality, productivity, and yield.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1462-1467
• /
• 2013

A pseudo 480-Hz drive method has been proposed to reduce the dynamic false contour noise that occurs on flat panel displays with displaying grayscale image in the digital mode, such as plasma display panels. The proposed method makes the image movements nearly continuous by rearranging the 8-bit image data displayed for 1 TV field into 8 subfields. The position of the image data rearranged in subfields has been optimized on the basis of the speed of the moving image by computer simulations for the dynamic false contour noise. It is verified that a significant reduction in the dynamic false contour noise is achieved with the proposed method as compared to the conventional noise reduction technologies. Moreover, to reduce the noise in digital mode displays, the proposed technology requires only 8 subfields. Therefore, there is no reduction in the brightness of the image.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.446-450
• /
• 2007

It is strongly expected that inkjet printing method will be play and important role on printable electronics such as 3D integration of embedded ceramic devices(capacitor, resistor, inductor and electrode or circuit), Si-TFT and organic TFT including display C/F, RFID, FPCB, and etc. A inkjet printing method had been center of attention to strengthen the competitiveness of flat panel display on market and to open the new world of manufacturing process of printable electronics. We will survey the industrial tendency of printable electronics and flat panel display including some examples of inkjet printing and present the considerable points of inkjet printing method and some role of materials for successful inkjet printing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.845-848
• /
• 2002

The study of photoconductor materials is demanded for development for flat-panel digital x-ray Imager. In this paper, We investigated the feasibility of application as x-ray image sensor using Cd(Zn)Te compound with high stopping power on high radiation. These Cd(Zn)Te samples were fabricated by vacuum thermal evaporation method to large area deposition and investigated I-V measurement as applied voltage. The experimental results show that the additional injection Zn in CdTe film reduced the leakage current, for the $Cd_{0.85}Zn_{0.15}Te$ detector, the net charge had the highest value as $144.58pC/cm^2$ at 30 V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.849-852
• /
• 2002

Recently, amorphous selenium is used as x-ray conversion material for flat-panel x-ray detector. In this paper, we investigated the effect of breakdown under high voltage and leakage current in PN-type multi-layer structure based on p-type a-Se and n-type conductive thin film. Experimental results show that the multi-layer based detector reduced leakage current because n-type CeO2 conductive layer prevent from hole injection into a-Se layer from collection electrode, Also, the breakdown voltage was improved by dielectric layer between a-Se and top electrode.