• Design & Manufacturing
• /
• 제17권4호
• /
• pp.63-71
• /
• 2023

In order to increase the extrusion production speed of aluminum, extrusion die cooling technology using liquid nitrogen has recently attracted a lot of attention. Increasing the extrusion speed increases the temperature of the bearing area of extrusion dies and the extrusion profile, which may cause defects on the surface of extruded profile. Extrusion die cooling technology is to directly inject liquid nitrogen through a cooling channel formed between the die and the backer inside the die-set. The liquid nitrogen removes heat from the die-set, and gaseous nitrogen at the exit of the channel, covers the extrusion profile of an inert atmosphere reducing the oxidation and the profile temperature. The aim of this study is to evaluate the cooling capacity by applying die cooling to extrusion of Al-Mn-based aluminum alloy flat tubes, and to investigate the effects of die cooling on the change in extrusion characteristics of flat tubes. Cooling capacity was confirmed by observing the temperature change of the extrusion profile depending on whether or not die cooling is applied. To observe changes in material characteristics due to die cooling, surface observation is conducted and microstructure and precipitate analysis are performed by FE-SEM on the surface and longitudinal cross section of the extruded flat tubes.

• 소성∙가공
• /
• 제4권2호
• /
• pp.141-150
• /
• 1995

The purpose of the open die press forging is to maximize the internal deformation for better structural homogeneity and center-line consolidation in case of the ingot. A two and three dimensional viscoplastic finite element analysis is carried out for the plate, cylinder and square forging with the flat die in order to study the forging effects during the process. Effect of width, height reduction, and die staggering are studied through simulation of the process. Thus favorable working conditions are suggested for better and more disirable product quality.

• Elastomers and Composites
• /
• 제57권4호
• /
• pp.147-156
• /
• 2022

In this study, we chose a flat die to optimize a general die geometry. The optimization was aimed at obtaining a uniform velocity distribution across the exit of the die. For the optimization, the input and output design parameters were randomly computed, and response surfaces were generated to obtain statistical data for the minimum and maximum sensitivities computed during optimization. Subsequently, object functions with constraints were numerically computed to obtain the minimum errors in the velocity difference (i.e., variable "Outp" in this study). Finally, we obtained the candidate optimized dataset. Note that the current numerical computations were simultaneously conducted for an entire extruder, i.e., screw plus die. The numerical outlet velocity distributions in the modified die geometry tended to be much more uniform than the conventional distributions in the current optimization processes for this specific flat die.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.98-101
• /
• 2001

In the present study, several design parameters of the flat-die extrusion process are investigated using the rigid-plastic finite element method. The effect of loaction of extrusion profile, arrangement of multiple extrusion profiles, and design of various die land has been investigated through the analysis. Several numerical examples of flat-die extrusion, such as C-section, multiple U- shape, and window guide extrusion, are analyzed. From the comparative study, the effect of design parameters is investigated. In each example, comparing the velocity distribution with that of the original design, it has been shown that the design modification affords much more uniform distribution of axial velocity

• 소성∙가공
• /
• 제10권7호
• /
• pp.551-557
• /
• 2001

In the present study, several design parameters of the flat-die extrusion process are investigated using the finite element method. The effects of the location of an extrusion profile, arrangement of multiple extrusion profiles, and the design of various die land have been investigated through the analysis. Several numerical examples of flat-die extrusion of such as C-section, multiple U-shape, and a window guide section, are analyzed. From the comparative study, the effect of design parameters is investigated. In each example, comparing the velocity distribution with that of the original design, it has been shown that the design modification affords more uniform distribution.

• 한국기계기술학회지
• /
• 제13권2호
• /
• pp.155-163
• /
• 2011

The flat type automotive cross members with high strength steel have advantages in light weight and fewer parts compared to the hump type cross members. But the complex part shape of the flat type cross member and the poor formability of high strength steel make it difficult to form the parts without forming defects, such as splits and wrinkles. The purpose of this study is to develop the flat type automotive cross member with high strength steel. For that purpose, drawing processes are evaluated using PAM-$STAMP^{TM}$ and proper draw die and blank designs are proposed. Using the proposed die and blank design, the flat type upper and lower cross member could be formed successfully without forming defects.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.262-265
• /
• 2005

A shape optimization of flow guide is accomplished to minimize the wear rate of die in three-dimensional flat-die extrusion processes. In order to achieve the balanced flow and the uniformed distribution of the effective strain during the extrusion, a multi-objective optimization is implemented. During the process of optimization formulation, the flow balance and the deviation of strain is considered as constrained conditions. The proposed approach is applied to an extrusion of H section. Through the optimization, it has been confirmed that the wear rate of die can be minimized satisfying the constraint.

• 한국정밀공학회지
• /
• 제13권12호
• /
• pp.136-141
• /
• 1996

In this paper, the design variables of the extruded parts involving flat die through model experiment are investigated to overcome some current problems such as bending and twisting and get more improved quality products. Above all, the deformation behavior is analyzed in experiment and investigated flow charactristics inside container. Finally, the straight extruded product is obtained by modified bearing land width on the basis of the exit velocities distribution from bended and twisted products.

• 소성∙가공
• /
• 제11권6호
• /
• pp.495-502
• /
• 2002

The welding pressure in extru bending process is affected by the shape of welding chamber of porthole die. It is very important to increase the welding pressure when the tube should be extruded particulary from four billets of the materials. The high circumferential stress of the tube can make the welding pressure increase during the extru-bending. In order to increase the circumferential stress, it is necessary to make the billets pass through the narrow gap between the conical die and the conical plug. This paper describes the welding pressure by the experiments and the analysis with the two types of the chamber. One of them is the chamber between the flat die and straight mandrel, and the other one is the chamber between the conical die and conical plug. The results of the experiments and the analysis shows that the conical chamber makes the welding pressure increase by the effect of the reducing diameter of tube and the welding pressure by the conical dic and plug is stronger than the welding pressure by the flat die and straight mandrel.

• 소성∙가공
• /
• 제7권3호
• /
• pp.246-259
• /
• 1998

This paper describes a research work of developing a computer-aided design and manufacturing of irregular shaped sheet metal product for blanking or piercing and bending operations. An approach to the system is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories experimental results and the empirical knowledge of field experts, This system has been written in AutoLISp on the AutoCAD and in customer tool kit on the SmartCAM with a personal computer and is composed of nine modules which are input and shape treatment, flat pattern-layout, pro-processor module. Based on the knowledge-based rules, the system is designed by considering several factors, such as material and thickness of product complexities of blank geometry and punch profile sheet metal to give flat pattern and automatically account for the adjustment of bending allowances to match tooling requirements by checking dimensions and generating NC data automatically according to drawings of die-layout module. Results carried out in each module will provide efficiencies to the designer and the manufacturer of blanking or piercing and bending die in this field.