• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.504-512
• /
• 2010

The paper proposes the 6bit 800MS/s flash A/D converter that can be applied to wireless USB chip-set. The paper simplified the error correction circuit and synchronization block as one circuit which are used respectively, and furthermore reduced the burden on the hardware. Comparing to the conventional error correction circuit, the proposed error correction circuit in this paper reduced 5 MOS transistors, the area of each error correction circuit is reduced by 9%. The A/D converter is fabricated with 0.18um CMOS 1-poly 6-metal process, and power dissipation is 182mW at 0.8Vpp input range and 1.8V supply voltage. The measured result shows 4.0bit of ENOB at 800MS/s conversion rate and 128.1MHz input frequency.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.3
• /
• pp.57-63
• /
• 2008

As diverse memory cards based on NAND flash memory are getting popularity with consumer electronics such as digital camera, camcorder and MP3 player the compatibility problems between a newly developed memory card and existent host systems have become a main obstacle to time-to-market delivery of product. The common practice for memory card compatibility test is to use a real host system as a test bed. As an improved solution, an FPGA-based prototyping board can be used for emulating host systems. However, the above approaches require a long set-up time and have limitations in representing various host and device systems. In this paper, we propose a co-validation environment for compatibility test between memory card and host system using formal modeling based on Esterel language and co-simulation methodology. Finally, we demonstrate the usefulness of the proposed environment with a case study of real memory card development.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.4
• /
• pp.325-336
• /
• 2013

FlashLinQ, one of the typical D2D communication systems developed by Qualcomm, considers a single-tone communication based distributed channel-aware link scheduling method to realize the link scheduling process with low control overheads. However, considering the frequency selective fading effect of practical multi-path channel, the single-tone based SIR estimation causes a critical scheduling error problem because the received single-tone signal has quite different channel gain at each sub-carrier location. In order to overcome this problem, we propose a novel link scheduling method based on CAZAC (Constant Amplitude Zero Auto-Correlation) sequence for D2D communication system. In the proposed method, each link has a unique offset value set for the generation of CAZAC sequences. CAZAC sequences with the cyclic offsets are transmitted using multiple sub-blocks in the entire bandwidth, and then each device can obtain nearly full-band SIR using a good cyclic cross-correlation property of CAZAC sequence.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.3
• /
• pp.453-460
• /
• 2014

Fault injection attack is the process of attempting to acquire the information on-chip through inject artificially generated error code into the cryptographic algorithms operation (or perform) which is implemented in hardware or software. From the details above, the laser-assisted failure injection attacks have been proven particularly successful. In this paper, we propose an improved laser probing system for fault injection attack which is called the Dual-Laser FA tool set, a hybrid approach of the Flash-pumping laser and fiber laser. The main concept of the idea is to improve the laser probe through utilizing existing equipment. The proposed laser probe can be divided into two parts, which are Laser-I for laser cutting, and Laser-II for fault injection. We study the advantages of existing equipment, and consider the significant parameters such as energy, repetition rate, wavelength, etc. In this approach, it solves the high energy problem caused by flash-pumping laser in higher repetition frequency from the fiber laser.

• KIISE Transactions on Computing Practices
• /
• v.21 no.2
• /
• pp.126-131
• /
• 2015

As flash-based storage systems have been actively employed in large-scale servers and data centers, reliability has become an indispensable element. One promising technique for enhancing reliability is static wear-leveling, which distributes erase operations evenly among blocks so that the lifespan of storage systems can be prolonged. However, increasing the capacity makes the processing overhead of this technique non-trivial, mainly due to searching for blocks whose erase count would be minimum (or maximum) among all blocks. To reduce this overhead, we introduce a new randomized block selection method in static wear-leveling. Specifically, without exhaustive search, it chooses n blocks randomly and selects the maximal/minimal erased blocks among the chosen set. Our experimental results revealed that, when n is 2, the wear-leveling effects can be obtained, while for n beyond 4, the effect is close to that obtained from traditional static wear-leveling. For quantitative evaluation of the processing overhead, the scheme was actually implemented on an FPGA board, and overhead reduction of more than 3 times was observed. This implies that the proposed scheme performs as effectively as the traditional static wear-leveling while reducing overhead.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.45-50
• /
• 2005

In this study, the casting/forging process was applied in manufacturing a low control arm, in order to prove that application of casting/forging process to Al6061 is likely to get the effect of light weight compared with existing steel products and to reduce the cost of materials. Firstly, In order to set up the optimum casting condition of the forging material, Al6061, casting experiments were carried out by controlling pouring temperature of the aluminum for casting, mold temperature, and pouring time. $700^{\circ}C$ pouring temperature, $300^{\circ}C$ mold temperature and 10-second pouring time were taken into account as the optimum casting conditions. With respect to a hot forging test, it is practiced on the basis of a temperature of materials, strain rate, and reduction rate so as to observe each microstructure and examine strain-stress curve simultaneously; examine tensile test and hardness test; eventually set up the optimum hot forging condition. A hot forging test, tensile test, hardness experiment, and microstructure observation were carried out on condition of $70\%$ reduction rate, $500^{\circ}C$ temperature of materials, and 1 strain rate. As a result of those experiments, 330MPa tensile strength, $16.4\%$ elongation, and 122.8Hv hardness were recorded. In oder to get a sound preform which has no unfitting cavity and less flash, two preforms were proposed on the basis of volume rate of the final product; the optimum volume rate of preform for the low control arm was $115\%$. In conclusion, it is confirmed that using the forging material rather than casting materials in casting/forging process is likely to get more superior mechanical properties. Compared with Al6061, performed by means of general forging, moreover, cast/forged Al6061 can not only stimulate productivity by reducing production processes, but cut down the cost of materials by reusing forging scraps.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.145-145
• /
• 2018

Small islands rely heavily on groundwater resources in addition to rainwater as the source of freshwater since surface water bodies are often absent. The groundwater resources are vulnerable to sea level rise, coastal flooding, saltwater intrusion, irregular pattern of precipitation resulting in long droughts and flash floods. Increase in population increases the demand for the limited groundwater resources, thus aggravating the problem. In this study, the effects of climate change on Tongatapu Island, Kingdom of Tonga, a small island in Pacific Ocean, are investigated using a sharp interface transient groundwater flow model. Twenty nine downscaled General Circulation Model(GCM) predictions are input to a water balance model to estimate the groundwater recharge. The temporal variation in recharge is predicted over the period of 2010 to 2099. A set of GCM models are selected to represent the ensemble of 29 models based on cumulative recharge at the end of the century. This set of GCM model predictions are then used to simulate a total of six climate scenarios, three each (2010-2039, 2040-2069, and 2070-2099) under RCP 4.5 and RCP 8.5. The impacts of predicted climate change on groundwater resources is evaluated in terms of freshwater volume changes and saltwater ratios in pumping wells compared to present conditions. Though the cumulative recharge at the end of the century indicates a wetter climate compared to the present conditions the large variability in rainfall pattern results in frequent periods of groundwater drought leading to saltwater intrusion in pumping wells. Thus for sustaining the limited groundwater resources in small islands, implementation of timely assessment and management practices are of utmost importance.

• Journal of Veterinary Clinics
• /
• v.37 no.3
• /
• pp.130-134
• /
• 2020

This study aimed to confirm the effects that the mobile phone has on Electroretinogram (ERG). The ERG responses of three groups of healthy dogs, five in each group, were studied. ERG test was performed consecutively before and after the mobile phone was carried out. For group A, music was played with the sound on; for group B, music was played but the sound off; and for group C, the phone was set on the airplane mode. In the presence of a mobile phone, the amplitudes of a- and b-wave were increased in all groups. The a- and b-wave amplitudes at the flash intensity of 3,000 mcd·s/㎡ were significantly increased in all groups (p < 0.05). Based on the results, it is recommended to conduct ERG test in the absence of a mobile phone for the accurate evaluation of the retinal function.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.52-57
• /
• 2015

The disease diagnosis system has been developed using the thin nitride(Si3N4) cantilever arrays which can measure the difference of capacitances between sensor and reference. The system consists of 32-bits RISC(Reduced Instruction Set Computer), RAM/Flash, bus, communication IP's, ADC(Analog Digital Converter) board, and LCD display. The marker selection method, which give us the good accuracy from reasonal numbers of markers, is suggested. The developed system has the resolution under 1fF and can detect 10nM concentration of Thrombin.

• Korean Journal of Health Education and Promotion
• /
• v.21 no.3
• /
• pp.151-177
• /
• 2004

Recently, the educational community has attempted to implement the theory of multiple intelligences. In approaching multiple intelligences, teachers have applied the same structural approach which has been so successful with cooperative learning. Cooperative learning is easy to learn and implement, fun for teachers and students, and produce profoundly positive outcomes along a remarkable number of dimensions. Different structures are designed for different outcomes, including enhanced mastery of subject matter, improved thinking skills, team building, class building, development of social character and social skills, communication skills, classroom management, classroom discipline, and development of and engagement of each of the multiple intelligences. Cooperative learning is becoming an increasingly popular teaching strategy. In this study, it is aimed to clarify the application of cooperative learning in health education. Cooperative Learning in health education enhances student learning by: 1) providing a shared cognitive set of information between students, 2) motivating students to learn the material, 3) ensuring that students construct their own health knowledge, 4) providing formative feedback, 5) developing social and health group skills necessary for success outside the classroom, and 6) promoting positive interaction between members of different cultural and socio-economic groups. Cooperative Learning structures and techniques in health education are following. Flash Card, Focused Listing, Structured Problem-solving, Paired Annotations, Structured Learning Team Group Roles, Send-A-Problem, Value Line, Uncommon Commonalities, Team Expectations, Double Entry Journal, Guided Reciprocal Peer Questioning, What if. Because the purpose of health education is the practice, therefore health specialists have to guide powerful and effective teaching method The application of cooperative learning in health education may improve its effectiveness.