• Tribology and Lubricants
• /
• v.4 no.2
• /
• pp.44-51
• /
• 1988

Titanium carbide(TiC), Titanium nitride(TiN), and Titanium carbonnitride(Ti(C,N)) films were deposited on $Si_3N_4$-TiC composite cutting tools by chemical vapor deposition(CVD) using $TiCl_4-CH_4-H_2$, $TiCl_4-N_2-H_2$, and $TiCl_4-CH_4-N_2-H_2$ gas mixtures, respectively. The experimental results indicate that TiC coatings compared with TiN coatings on $Si_3N_4$ -TiC ceramic have an improved microstructural property, good thermal shock resistance, and good interfacial bonding. However TiN coatings compared with TiC coatings have a low friction coefficient with steel and good chemical stability. It is found by cutting test that coated insert compared with $Si_3N_4$-TiC ceramic have a superior flank and crater wear resistance. And multilayer coating compared with monolayer coating shows a improved wear resistance.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.3
• /
• pp.31-37
• /
• 2011

The purpose of this study is to investigate cutting characteristics and wear behavior in SCM440 steel with different cutting tools, CBN(Cubic Boron Nitride) and coated CBN. During the test coated CBN tool especially with TiAlN showed better wear resistance behavior than orginal CBN tools. In the interrupted cutting condition, axial groove affected tool surface with impact force during the turning operation. For advantageous turning parameter in the interrupted process it is recommendable that lower speed. Also surface roughness showed better behavior in the coated CBN tool conditions than normal CBN conditions. Mainly this is caused by reduced friction between material and tool surface with coated layer.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.72-77
• /
• 2019

In this study, the wear characteristics of end mills for CFRP processing were investigated according to the tool materials and coating types. Three kinds of tool materials and two types of coatings were used for comparing the machining performance. The flank wear of the end mill tool and the surface condition of the workpiece were compared. The K6UF material shows the most excellent performance among the three materials used in the experiment. The Tetrabond coating showed better processability in comparison of two kinds of coatings.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.604-610
• /
• 1989

This paper is concerned with the machinability of fine ceramics(Al$_{2}$O$_{3}$) by using sintered diamond tools. For this purpose, ceramics cutting experiments under various cutting conditions such as cutting speed, feed rate, and others were carried out. The main results are follows : (1) During the cutting of fine ceramics, the used tools were found to be slightly chattering at cutting speed of 70m/min, and at cutting speed of higher than this I found the fine ceramics difficult to be cut. (2) When I used a tool with large nose radius, there occured a small amount of wear on the flank of the tool. However, at the early stage of fine ceramics cutting, the tools with smaller nose radii were required mainly to prevent the chipping of the ceramics. (3) When the materials were dry-cut, the appropriate cutting speel was found to be lower than 40m/min, and when the materials were dry-cut, I could cut them without any difficulty even at the speed of 70m/min, the surface roughness of ceramics cut at the speed of 70m/min was considerly fine. (4) It is generally believed that the principal cutting force is the largest in the case of steels cutting, but I found the thrust cutting force to be larger than any other cutting forces in the case of ceramics cutting.

• Journal of Mechanical Science and Technology
• /
• v.18 no.5
• /
• pp.770-779
• /
• 2004

This paper describes the micro cutting of wear resistant tungsten carbides using PCD (Poly-Crystalline Diamond) cutting tools in performance with SEM (Scanning Electron Microscope) direct observation method. Turning experiments were also carried out on this alloy (V50) using a PCD cutting tool. One of the purposes of this study is to describe clearly the cutting mechanism of tungsten carbides and the behavior of WC particles in the deformation zone in orthogonal micro cutting. Other purposes are to achieve a systematic understanding of machining characteristics and the effects of machining parameters on cutting force, machined surface and tool wear rates by the outer turning of this alloy carried out using the PCD cutting tool during these various cutting conditions. A summary of the results are as follows: (1) From the SEM direct observation in cutting the tungsten carbide, WC particles are broken and come into contact with the tool edge directly. This causes tool wear in which portions scrape the tool in a strong manner. (2) There are two chip formation types. One is where the shear angle is comparatively small and the crack of the shear plane becomes wide. The other is a type where the shear angle is above 45 degrees and the crack of the shear plane does not widen. These differences are caused by the stress condition which gives rise to the friction at the shear plane. (3) The thrust cutting forces tend to increase more rapidly than the principal forces, as the depth of cut and the cutting speed are increased preferably in the orthogonal micro cutting. (4) The tool wear on the flank face was larger than that on the rake face in the orthogonal micro cutting. (5) Three components of cutting force in the conventional turning experiments were different in balance from ordinary cutting such as the cutting of steel or cast iron. Those expressed a large value of thrust force, principal force, and feed force. (6) From the viewpoint of high efficient cutting found within this research, a proper cutting speed was 15 m/min and a proper feed rate was 0.1 mm/rev. In this case, it was found that the tool life of a PCD tool was limited to a distance of approximately 230 m. (7) When the depth of cut was 0.1 mm, there was no influence of the feed rate on the feed force. The feed force tended to decrease, as the cutting distance was long, because the tool was worn and the tool edge retreated. (8) The main tool wear of a PCD tool in this research was due to the flank wear within the maximum value of $V_{max}$ being about 260 $\mu\textrm{m}$.

• Journal of Powder Materials
• /
• v.15 no.5
• /
• pp.359-364
• /
• 2008

To satisfy the demand of higher cutting performance, mechanical properties with tungsten carbide (WC-Co) tool materials were investigated. Hardness and transverse rupture strength with WC grain size, Co content and density were measured. Compared to H, K, and S manufacture maker as tungsten carbide (WC-Co) tool materials were used for high-speed machining of end-milling operation. The three tungsten carbide (WC-Co) tool materials were evaluated by cutting of STD 11 cold-worked die steel (HRC25) under high-speed cutting condition. Also, tool life was obtained from measuring flank wear by CCD wear measuring system. Tool dynamometer was used to measure cutting force. The cutting force and tool wear are discussed along with tool material characteristics. Consequently, the end-mill of K, H manufacture maker showed higher wear-resistance due to its higher hardness, while the S maker endmill tool showed better performance for high metal removal.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.1-6
• /
• 2018

Micro prism pattern is applying in order to get increase of luminance, control the light, and so forth especially in optics and display industry. Most patterns are fabricated by lithography, planning, and EDM, but they have limitations on the productivity or the unit cost of produce. However, ultra precision mold is one of the processes able to replace it, and assure high productivity required by industries. In this investigation, micro prismatic end-milling is suggested in order to fabricate the pattern effectively. Micro prism pattern having $100{\mu}m$ of pitch and height was machined on STD-11. After machining, the flank and boundary wear on micro end mill were measured and analyzed, as well as burr formation and dimensional accuracy of fabricated pattern were evaluated. Thus the optimal cutting conditions were derived.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.27-37
• /
• 1993

In unmanned machining, One of the most essential issue is the tool management system which includes controlling. identification, presetting and monitoring of cutting tools. Especially the monitoring of tool wear and fracture may be the heart of the system. In this study a computer vision based tool monitoring system is developed. Also an algorithm which can determine the tool condition using this system is presented. In order to enhance practical adaptability the vision system through which two modes of images are taken is located over the rake face of a tool insert. And they are analysed quantitatively and qualitatively with image processing technique. In fact the morphologies of tool fracture or wear are occurred so variously that it is difficult to predict them. For the purpose of this problem the pattern recognition is introduced to classify the modes of the tool such as fracture, crater, chipping and flank wear. The experimental results performed in the CNC turning machine have proved the effectiveness of the proposed system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1991.04a
• /
• pp.166-175
• /
• 1991

공구수명에 관한 신뢰성 높은 기준 절삭데이타의 수집은 기계가공시스템을 설계, 운영하는데 중요한 것이다. 이제까지 발표된 절삭공구의 마모측정용 센서로는 절삭저항, AE센사, 진동, 절삭온도 등이 있으며, 이 센서들은 공구마모 특히 플랭크 마모(flank wear) 와 간접적인 관계를 갖고서 별도의 사전 절삭실험에 의해 마모량과 신호 level의 상관관계 및 조정이 필요하기 때문에 본 연구팀에서는 직접적으로 공구마모 상태를 검출하고, 신뢰성이 높은 절삭공구의 마모정보를 얻기 위해 최근 그 응용범위가 확대되고 있는 영상처리기술을 응용한 공구마모 측정장치를 구성하였다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.85-91
• /
• 2013

The machinability of wear-resistible tungsten carbides and the tool wear behavior in machining of V30 and V50 tungsten carbides using PCD (Poly Crystalline Diamond) cutting tool was investigated to understand machining characteristics. This material is one of the difficult-to-cut materials in present, but their usage has been already broadened to every commercial applications such as mining tools, and impact resistant tools etc. Summary of the results are as follows. (1) Tool wear progression of PCD tools in turning of wear-resistible tungsten carbides were observed specially fast in primary cutting distance within 10m. (2) Three components of cutting resistance in this research were different in balance from the ordinary cutting such as that cutting of steel or cast iron. Those were expressed large value by order of thrust force, principal force, feed force. (3) If presume from viewpoint of high efficient cutting within this research, a proper cutting speed was 15m/min and a proper feed rate was 0.1mm/rev. In this case, it was found that the tool life of PCD tool was cutting distance until 230m approximately. (4) In cutting of wear-resistible tungsten carbides such as V30 and V50, it was recognized that the tool wear rate of V30 was very fast as compared with V50. (5) When the depth of cut was 0.1mm, there was no influence of the feed rate on the feed force. And the feed force tended to decrease as the cutting distance was long, because the tool was worn and the tool edge retreated. (6) It was observed that the tungsten carbides were adhered to the flank.