• 한국분무공학회지
• /
• 제20권2호
• /
• pp.107-113
• /
• 2015

To date, the demand for Combined Cycle Power Plant (CCPP) has been continuously increased to overcome the problem of air pollution and lack of energy. In particular, the underground CCPP is exposed to substantial fire and explosion risks induced by gas leakage. The present study conducted numerical simulations to examine the fire behavior and gas leakage characteristics for a restricted region including gas turbine and other components used in a typical CCPP system. The commercial code of FLUENT V.14 was used for simulation. From the results, it was found that flammable limit distribution of leakage gas affects fire behavior. Especially, the flame is propagated in an instant in restricted region with LNG gas. In addition, consequence analysis factors such as critical temperature and radiation heat flux are introduced. These results would be useful in making the safety guidelines for the underground CCPP.

• 한국분무공학회지
• /
• 제4권2호
• /
• pp.19-32
• /
• 1999

The present study investigated the forms and behaviors of fuel during intake and compression process, and the initial flame stability in a lean burn engine modified as a single cylinder engine equipped with quartz windows for visualization. PLIF(Planar Laser Induced Fluorescence) method with KrF Excimer laser was used for measuring the fuel distributions. The principal design concept of the lean burn nin in this study is the axial stratification in the fuel distribution via fuel injection during intake process and different shapes of intake ports; helical and straight. The experiments showed that fuel flowed in as a vapor state in the early part of intake process and lots of this mixture mated down along the intake valve side cylinder wall, but in the latter part, a lot of fuel flowed in as a liquid state and this fuel stayed in the upper part of cylinder, after that the dense fuel cloud moved upward in the early of part compression process. It became clear that the fuel flowed in via straight port had a important role in the axial fuel stratification.

• 한국화재소방학회논문지
• /
• 제34권1호
• /
• pp.26-36
• /
• 2020

랙크식 창고 화재의 경우 랙크에 적재된 가연성물품사이의 송기공간을 통한 급격한 화재확산으로 인해 화재진압이 매우 어렵다. 현재 국내 랙크식 창고의 소방시스템은 많은 문제점이 있으며, 이를 해결하기 위하여 새로운 소방시스템을 설계되고 개발되었다. 극 초기감지와 화재발생위치정보를 얻기 위하여 감지기 네트워크와 인공지능을 활용한 지능형 시스템을 설계되었다. 극초기에 화재 위치 인근에서 살수가 가능하도록 수직 일제살수 배관과 습식배관, 그리고 전자밸브를 사용하여 시스템을 구성하였다. 설계 결과를 기반으로 실제 시스템의 설치 및 실대형 시험을 진행하였으며, 성공적으로 시험이 완료되었다.

• 한국분무공학회지
• /
• 제2권4호
• /
• pp.47-53
• /
• 1997

By using a premixed laminar burner, the effect of mixture component on laminar burning velocity($S_L$) was investigated. The following was made clear ; (1)As the humidity$(H_2O)$, $CO_2$ and Ar in mixture is increased, $S_L$ decreased in proportion to quantity of those dilution gases. (2) The heat reaction theory says that mean thermal conductivity $(\lambda_m)$, specific heat $(C_{pm})$ of mixture and adiabatic flame temperatures $(T_b)$ affect $S_L$. As a result of theoretical analysis, the effect of $\lambda_m\;and\;C_{pm}$ on $S_L$ is less than 1/25 of the effect of $T_b$, so the effect of $\lambda_m\;and\;C_{pm}$ can be ignored. (3) From experimental results, it was confirmed that $\ln(S_L)$ is proportional to $(1/T_b)$, that is, the effect of $H_2O$ on $S_L$ is mainly caused by changes of $T_b$. This conclusion was verified by the fact increases of $H_2O,\;CO_2$ and Ar decrease the intensity of radiation typical $C_2$, CH, and OH in the same manner.

• Journal of Welding and Joining
• /
• 제17권4호
• /
• pp.53-59
• /
• 1999

Amorphous alloys have also been called glassy alloys or non-crystalline alloys. They are made by the rapid solidification. The solidification occurs so rapid that the atoms are frozen in their liquid configuration. There are unique magnetic, mechanical, electrical and corrosive behaviors which result form their amorphous structure. In the study. amorphous coatings were manufactured with Ni-Cr-B-Si powders by flame spray. Measurement of hardness, were resistance, corrosion resistance and observation of microstructures and XRD, DSC were performed to investigate characteristics of amorphous coatings. The experimental results obtained as follow: 1) Amorphous powders could not be manufactured with the spraying in the spraying in the liquid nitrogen. But, amorphous coatings could be manufactured with the rotation cooling method by liquid nitrogen. In the fabrication of amorphous coatings, major factor was the rapid cooling by rotation of the substrate. 2) Hardness of coatings was obtained Hv 960 by formation of amorphous phase. But, wear resistance decreased. That was due to porosity in the coatings by the rapid cooling. 3) In the case of corrosion resistance, amorphous coatings were superior to air-cooled coatings. That was due to formation of amorphous phase. 4) After amorphous coatings were heat-treated at 520℃ for 1hr. hardness increased 80% and wear resistance increased 30% comparing with air cooled coatings. These were due to crystallization of amorphous phase and decrease of porosity by heat-treatment.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.32-39
• /
• 2004

HCCI (Homogeneous Charge Compression Ignition) combustion has a great advantage in reducing NOx (Nitrogen Oxides) and PM (Particulate Matter) by lowering the combustion temperature due to spontaneous ignitions at multiple sites in a very lean combustible mixture. However, it is difficult to make a diesel-fuelled HCCI possible because of a poor vaporability of the fuel. To resolve this problem, the two-stage injection strategy was introduced to promote the ignition of the extremely early injected fuel. The compression ratio and air-fuel ratio were found to affect not only the ignition, but also control the combustion phase without a need for the intake-heating or EGR (Exhaust Gas Recirculation). The ignition timing could be controlled even at a higher compression ratio with increased IMEP (Indicated Mean Effective Pressure). The NOx (Nitrogen Oxides) emission level could be reduced by more than 90 % compared with that in a conventional DI (Direct Injection) diesel combustion mode, but the increase of PM and HC (Hydrocarbon) emissions due to over-penetration of spray still needs to be resolved.

• 동력기계공학회지
• /
• 제18권2호
• /
• pp.37-42
• /
• 2014

The purpose of this paper is to investigate polarization characteristics of heat-treated Ni-based self-flux alloy coating in alkaline solution. Ni-based self-flux alloy powder was sprayed to a steel substrate using flame spray process, and heat treatments were performed in a vacuum furnace at $800^{\circ}C$, $900^{\circ}C$, $1000^{\circ}C$ and $1100^{\circ}C$. After heat treatments, corrosion tests were carried out using potentiostat/galvanostat at solution with pH 8 and pH 13. Corrosion potential(Ecorr) and corrosion current density(Icorr) could be analyzed from polarization curve. Anticorrosive effect of heat-treated coating at solution with pH 8 was relatively greater than at solution with pH 13. Heat-treated coating at $1100^{\circ}C$ showed the greatest anti-corrosion characteristics in alkaline solution.

• 한국분무공학회지
• /
• 제19권2호
• /
• pp.75-81
• /
• 2014

Swirl flow in the gun type burner has a decisive effect on the stabilization of the flame, improvement of the combustion efficiency, and also a reduction of NOx. This swirl flow is created by the spinner which is inside the airtube that guide the combustion air. Gun type burner has generally the inner devices composed nozzle adapter, spark gap ignitor, and spinner. These inner components change the air flow behavior passing through air tube. Meanwhile, turbulent characteristics of this air flow are important to understand the combustion phenomena in the gun type burner, because the mixture of fuel and air are depended on. However, nearly all of the studies have been analyzed the turbulent flow of simplified combustion formation without the inner devices. So, this study conducted the measurement using by hot-wire anemometer and analyzed turbulent flow characteristics of the swirl flow discharged from the air tube with inner devices. Turbulence characteristics come up in this study were turbulence intensity, kinetic energy and shear stress of the air flow with the change of the distance of axial direction from the exit of the air tube.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.177-180
• /
• 2010

혼합비와 연소압에 따른 이중 와류 동축 분사기의 유량계수 변화를 살펴보았다. 연료 과농 조건에서 액체산소와 케로신을 이용하여 이중 와류 동축 분사기의 연소시험을 수행하였다. 두 종류의 분사기가 시험에 적용되었는데, 산화제 분무각 변화에 의한 추진제간 모멘텀 비 차이와 연료 노즐 직경 차이로 인한 유량계수 영향 특성이 파악되었다. 연료 와류실을 연료가 모두 채운 상태에서 연소가 이루어지는 경우 화염 구조의 변화가 없어 혼합비에 다른 유량계수 변화 또한 보이지 않는 것으로 파악하였다.

• 한국재료학회지
• /
• 제25권10호
• /
• pp.571-576
• /
• 2015

The effects of coating thickness on the delamination and fracture behavior of thermal barrier coating (TBC) systems were investigated with cyclic flame thermal fatigue (FTF) and thermal shock (TS) tests. The top and bond coats of the TBCs were prepared by electron beam-physical vapor deposition and low pressure plasma spray methods, respectively, with a thickness ratio of 2:1 in the top and bond coats. The thicknesses of the top coat were 200 and $500{\mu}m$, and those of the bond coat were 100 and $250{\mu}m$. FTF tests were performed until 1140 cycles at a surface temperature of $1100^{\circ}C$ for a dwell time of 5 min. TS tests were also done until more than 50 % delamination or 1140 cycles with a dwell time of 60 min. After the FTF for 1140 cycles, the interface microstructures of each TBC exhibited a sound condition without cracking or delamination. In the TS, the TBCs of 200 and $500{\mu}m$ were fully delaminated (> 50 %) within 171 and 440 cycles, respectively. These results enabled us to control the thickness of TBC systems and to propose an efficient coating in protecting the substrate in cyclic thermal exposure environments.