• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.204-215
• /
• 2011

Flame stability is the one of the main mechanism of laminar lifted flame and flame propagation velocity becomes a yardstick to measure the flame stability. Bilge has presented the flame propagation velocity of the triple flame and the flame stability mechanism related the flame configuration and mixture fraction. However, there was not able to observe all process of flame ignition and extinction for small nozzle diameter. In this paper, we have subdivided the flame configuration and stability mechanism and classified the flame behavior with a nozzle diameter. Also we have subdivided the 'triple flame propagation opened' and the 'triple flame propagation closed' from the triple flame propagation of triple flame criterion.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.12
• /
• pp.1557-1566
• /
• 2004

A flame extinction phenomenon is a typical unsteady process in combustion. Flame extinction is characterized by various physical phenomena, such as convection, diffusion, and the production of heat and mass. Flame extinction can be achieved by either increasing the strain rate or curvature, by diluting an inert gas or inhibitor, or by increasing the thermal or radiant energy loss. Though the extinction is an inherently transient process, steady and quasi-steady approaches have been used as useful tools for understanding the flame extinction phenomenon. Recently, unsteady characteristics of flames have been studied by many researchers, and various attempts have been made to understand unsteady flame behavior, by using various extinction processes. Representative parameters for describing flame, such as flame temperature, important species related to reactions, and chemi-luminescence of the flame have been used as criterions of flame extinction. In these works, verification of each parameter and establishing the proper criterions of the extinction has been very important. In this study, a time-dependent flame temperature and an OH radical concentration were measured using optical methods, and the instantaneous change of the flame luminosity was also measured using a high-speed ICCD (HICCD) camera. We compare the unsteady extinction points obtained by three different methods, and we discuss transient characteristics of maximum flame temperature and OH radical distribution near the extinction limit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1209-1215
• /
• 2012

Experiments with premixed flames in a tube have been conducted to investigate the transition phenomenon from a laminar flat flame to turbulent motions. To induce this phenomenon, a flat flame is formed in a tube. Then, the local velocity at the center of the flat flame surface is increased using $CO_2$ laser irradiation. The deformed flame front propagates with an increase in the total flame surface and oscillating instability. Eventually, the flame front accelerates explosively, and it shows turbulent flame motions with a strong noise. The dynamic behaviors of the flame front prior to the turbulent motions are analyzed in this study to elucidate this process. The physical model of the process is presented according to observations.

• Fire Science and Engineering
• /
• v.17 no.3
• /
• pp.20-25
• /
• 2003

Measurements with filaments and thermocouples and computations with Oppdif and FDS were carried out to investigate the impact of flame strain, agent addition, and buoyancy on the structure and extinction of nonpremixed counterflow flames. Measurements through 2.2 s drop tests in microgravity conditions and experiments in normal gravity conditions were compared with the results of computations. For the global strain rates 7 s$^{-1}$ through 100 s$^{-1}$ , the turning point behavior in the critical nitrogen concentration at O-g was confirmed. The effects of buoyancy, that is, changes in the flame curvature and thickness were also confirmed by the computations with FDS. There was agreement in the peak flame temperature and its position between the computations and the measurements in the near extinction methane/air diffusion flames in microgravity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.70-77
• /
• 1986

Turbulent mixing field with recirculating flow which is formed by injecting gaseous fuel on the main air stream is solved numerically by a finite difference method. The turbulence model for obtaining transport properties was k-.epsilon. model, which was obtained from turbulent kinetic energy and its dissipation rate. Considering the effects of streamline curvature, modified k-.epsilon model was used. Generally, Modified k-.epsilon. model makes better predictions than standard model, and from this result, it is recognized that standard model has deficiency when applied to turbulent recirculating flows, and that modified k-.epsilon. model takes into account of streamline curvature effects properly. Meanwhile, A more study will be necessary to find the reason why large differences between predicted and experimental turbulent kinetic energy exist.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.399-408
• /
• 2010

The characteristics of lifted laminar propane flames diluted with nitrogen have been investigated experimentally to elucidate self-excitation and the effects of flame curvature. Flame oscillation modes are classified as follows: oscillation induced by heat loss, a combination of oscillations induced by heat loss and buoyancy, and a combination of the oscillations induced by heat loss and diffusive thermal instability. It is shown that the oscillation induced only by heat loss is not relevant to the diffusive thermal instability and hydrodynamic instability caused by buoyancy; this oscillation is observed under all lift-off flame conditions irrespective of the fuel Lewis number. These experimental evidences are displayed through the analysis of the power spectrum for the temporal variation of lift-off height. The possible mechanism of the oscillation induced by heat loss is also discussed.

• Journal of the Korean Institute of Gas
• /
• v.12 no.2
• /
• pp.77-84
• /
• 2008

Experimental study was conducted to clarify the importance of buoyancy effects in laminar lifted flames which have been well understood by cold jet similarity theory. To evaluate buoyancy effects, lifted flame behaviors were systematically observed in methane and propane lifted flames diluted with He as changing the fuel nozzle diameter from 0.1 to 6 mm. Important physical parameters such as fuel strength, flame stretch and flame curvature, which were derived through simple physical scaling laws, were estimated. It is experimentally proven that buoyancy effects are important in relatively large fuel nozzle diameter and large fuel dilution with He. The results of Chen et al., which displayed the existence of stably lifted flames for 0.5

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.287-288
• /
• 2012

DNS is performed to examine the propagation characteristics of stagnating turbulent premixed flames. Results show good agreement with the recently proposed relationship for turbulent burning velocity, $S_T$. It is shown that $S_T$ increases through a thinner flamelet, turbulence production and correlation between fluctuating velocity and buoyancy force respectively for diffusive-thermal, hydrodynamic and Rayleigh-Taylor instability. The mean curvature doesn't have significant effect on $S_T$ at the leading edge.

• Ocean Systems Engineering
• /
• v.13 no.4
• /
• pp.367-384
• /
• 2023

Herein, we present the design and development of an efficient finite element analysis model for thermal plate forming in shipbuilding. Double curvature shells in the ship building industries are primarily formed through the thermal forming technique. Thermal forming involves heating of steel plates using heat sources like oxy-acetylene gas torch, laser, and induction heating, etc. The differential expansion and contraction across the plate thickness cause plastic deformation and bending of plates. Thermal forming is a complex forming technique as the plastic deformation and bending depends on many factors such as peak temperature, heating and cooling rate, depth of heated zone and many other secondary factors. In this work, we develop an efficient finite element analysis model for the thermo-mechanical analysis of thermal forming. Different simulations are reported to study the effect of various parameters affecting the process. Temperature dependent properties are used in the analysis and the finite element analysis model is used to identify the critical flame velocity to avoid recrystallization of plate material. A spring connected plate is modeled for structural analysis using spring elements and that helps in identifying the resultant shapes of various thermal forming patterns. Finally, detailed simulation results are reported to establish the efficacy, applicability and efficiency of the designed and developed finite element analysis model.

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.32-37
• /
• 2009

In shipyard, plate forming is widely used to form the ship hull plate in various shapes. Line heating method by using a flame torch is one of the major shipbuilding processes carried out by skilled workers. Since the forming characteristics depend upon their experiences in manual forming, there are much variations between products and difficulties in communication between engineers and workers. Hence, it needs to develop an automatic forming system which can not only reduce the working time and rework costs but also improve the working environment and hull forming productivity. One of the final goals of plate forming automation is to form a target shape from the initial plate automatically. For automated plate forming, it is required to determine where and how to heat on the plate. To realize this procedure, the inverse problem should be first solved and the effect of curvature shape formed at the heating path should be investigated. In this study, the inverse problem was solved by geometrical approach using the relationship between bending angle and radius of curvature of the curved shape. In addition, experiments of two-dimensional plate forming were performed with the distance-based method considering the curved bending with curvature. The result of the formed shape agreed considerably well with the target shape.