• Journal of Sensor Science and Technology
• /
• v.21 no.3
• /
• pp.211-216
• /
• 2012

Fires are the most common disaster and early fire detection is of great importance to minimize the consequent damage. Simple sensors including smoke detectors are widely used for the purpose but they are able to sense fires only at close proximity. Recently, due to the rapid advances of relevant technologies, vision-based fire sensing has attracted growing attention. In this paper, a novel visual sensing technique to automatically detect fire is presented. The proposed technique consists of multiple steps of image processing: pixel-level, block-level, and frame level. At the first step, fire flame pixel candidates are selected based on their color values in YIQ space from the image of a camera which is installed as a vision sensor at a fire scene. At the second step, the dynamic parts of flames are extracted by comparing two consecutive images. These parts are then represented in regularly divided image blocks to reduce pixel-level detection error and simplify following processing. Finally, the temporal change of the detected blocks is analyzed to confirm the spread of fire. The proposed technique was tested using real fire images and it worked quite reliably.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.427-430
• /
• 2007

Many victims and property damages are caused in fires every year. In this paper, flame and smoke detection algorithm by using image processing technique is proposed to early alarm fires. The first decision of proposed algorithms is to check candidate of flame region with its unique color distribution distinguished from artificial lights. If it is not a flame region then we can check to candidate of smoke region by measuring difference of brightness and chroma at present frame. If we just check flame and smoke with only simple brightness and hue, we will occasionally get false alarms. Therefore we also use motion information about candidate of flame and smoke regions. Finally, to determine the flame after motion detection, activity information is used. And in order to determine the smoke, edges detection method is adopted. As a result of simulation with real CCTV video signal, it is shown that the proposed algorithm is useful for early fire recognition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1375-1381
• /
• 2011

Combustion processes in an optically-accessible single-cylinder heavy-duty diesel engine equipped with a highpressure common-rail injection system were investigated for JP-8 and diesel. Direct imaging and two-color thermometry were employed to verify the emission trend for both fuels. The combustion process was characterized by image analysis with focus on luminosity. The results of two-color thermometry were analyzed on the basis of the flame temperature and KL factor distribution. Analysis of the combustion process by direct imaging showed that the ignition delay was longer for JP-8 than for diesel, while the flame was extinguished rapidly. Analysis of the flame luminosity showed that the combustion intensity was higher for diesel and that the flame lasted for a longer duration in this case. Two-color thermometry results showed that the high-temperature region extended over a large area during JP-8 combustion, implying the formation of a large amount of $NO_x$. In addition, the KL factor showed low level over a large area and relatively homogeneous in the case of JP-8 combustion, which implied that less smoke was produced when using this fuel.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.112-117
• /
• 2001

An experiment using high preheated and swirled air in the coaxial diffusion flame burner was carried out in order to decrease NOx emission and improve the thermal efficiency. $N_2$ gas was used for diluent and propane was utilized for fuel. Combustion using high preheated air has two remarkable characteristics ; (1) low NOx emission with increasing dilution level, (2) high thermal efficiency in the furnace. Also, swirled air can mix fuel and oxidizer well in condition of diffusion flme and maintain the stable combustion. The color of flame changes from yellow to blue green according to increasing the dilution level of mixture gas. NO emission decreased with increasing dilution level and the swirl number.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.103-110
• /
• 1998

This experiment is performed to investigate the effects of the emulsion on the flame temperature and soot formation in a diesel engine. The two-color method is used to measure the flame temperature for combustion of emulsified diesel in the Rapid Compression and Expansion Machine(RCEM). The concentration of soot is estimated via calculation of the KL factor. The solenoid valve, elecronic controller and needle lift sensor are used to control the exact injection timing and duration under various operating conditions. According to the results the soot concentration is reduced with the increasing W/O while the temperature reduced. The pressure data and the flame images captured by a high speed camera show that the ignition delay of emulsified diesel increase the duration of premixed combustion. The sizes of water drops are measured to be about 10${\mu}m$ by a microscope.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.7
• /
• pp.889-898
• /
• 2003

The soot yield is studied by a premixed propane-oxygen-inert gas combustion in a specially designed disk-type constant-volume combustion chamber to investigate the effect of turbulence on soot formation. Premixtures are simultaneously ignited by eight spark plugs located on the circumference of chamber at 45 degree intervals in order to observe the soot formation under high pressures and high temperatures. The eight flames converged compress the end gases to a high pressure. The laser schlieren and direct flame photographs for observation field with 10 mm in diameter are taken to examine into the behaviors of flame front and gas flow in laminar and turbulent combustion. The soot volume fraction in the chamber center during the final stage of combustion at the highest pressure is measured by the in situ laser extinction technique and simultaneously the corresponding burnt gas temperature by the two-color pyrometry method. It is found that the soot yield of turbulent combustion decreases in comparison with that of laminar combustion because the burnt gas temperature increases with the drop of heat loss.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.4
• /
• pp.403-411
• /
• 2001

A criterion for evaluation of burners has changed recently, and the environmental problems are raised as a global issue. Burners with higher thermal efficiency and lower oxygen in the exhaust gas, evaluated better. To comply with environmental regulations, burners must satisfy the $NO_x$ and CO regulation. Consequently. 'good burner' means one whose thermal efficiency is high under the constraint of $NO_x$ and CO consistency. To make existing burner satisfy recent criterion, it is highly recommended to develop a feedback control scheme whose output is the consistency of $NO_x$ and CO. This paper describes the development of a real time flame diagnosis technique that evaluate and diagnose the combustion states, such as consistency of components in exhaust gas, stability of flame in the quantitative sense. In this paper, it was proposed on the flame diagnosis technique of burner using Neuro- Fuzzy algorithm. This study focuses on the relation of the color of the flame and the state of combustion. Neuro- Fuzzy learning algorithm is used in obtaining the fuzzy membership function and rules. Using the constructed inference algorithm, the amount of $NO_x$ and CO of the combustion gas was successfully inferred.

• Horticultural Science & Technology
• /
• v.35 no.4
• /
• pp.418-430
• /
• 2017

The objective of this study was to understand the combined effect of shading treatment and harvest time on pungency, ascorbic acid content, market-quality pepper yield, and photosynthetic activity in a yellow 'Star Flame' and 'Fire Flame' F1 hybrid pepper cultivar (Capsicum annuum). Plants were cultivated in a greenhouse under white, red, and green shading nets and compared to those grown under unshaded control conditions. The ascorbic acid and pungency parameters were analyzed by high-performance liquid chromatographic methods. Ascorbic acid, a compound of high nutritive value in pepper, was highest in fruits gathered during the first summer harvest in both hybrids. The ascorbic acid content was found to be further increased in fruits from plants grown under white net shading in both 'Star Flame' and 'Fire Flame'. Total capsaicinoid contents in 'Star Flame' were influenced by the interaction of shading treatment and harvest time (p = 0.004), with the lowest amounts ($241.2-251.5mg{\cdot}kg^{-1}$ fresh weight) resulting from white and red shading treatments at the early autumn harvest. In 'Fire Flame', both shading treatment (p = 0.009) and harvest time (p < 0.001) affected total capsaicinoid contents. We observed significantly higher total capsaicinoid contents in control fruits compared to that resulting from red and green shading treatments at the second harvest, and that resulting from red shading treatment at the third harvest. Analysis of photosynthetic activity revealed a significant and negative correlation between Fv/Fm values and total capsaicinoid contents in both hybrids (p < 0.001). Based on the obtained results, the harvest of peppers during summer should be promoted to produce fruits with high pungency.

• Journal of KIISE:Software and Applications
• /
• v.37 no.9
• /
• pp.712-721
• /
• 2010

This paper proposes a new fire-flame detection method using probabilistic membership function of visual features and Fuzzy Finite Automata (FFA). First, moving regions are detected by analyzing the background subtraction and candidate flame regions then identified by applying flame color models. Since flame regions generally have continuous and an irregular pattern continuously, membership functions of variance of intensity, wavelet energy and motion orientation are generated and applied to FFA. Since FFA combines the capabilities of automata with fuzzy logic, it not only provides a systemic approach to handle uncertainty in computational systems, but also can handle continuous spaces. The proposed algorithm is successfully applied to various fire videos and shows a better detection performance when compared with other methods.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.38 no.3
• /
• pp.404-414
• /
• 2014

This study investigates the dyeability and fastness of jacquard fabric for blind using low-melting flame retardant polyester. Two types of jacquard fabric were prepared with a low-melting flame retardant polyester and regular polyester. The low-melting flame retardant polyester has a sheath and a core. The core consists of flame retardant polyester and the sheath consists of low-melting polyester. Disperse red 50 (DR 50), disperse blue 56 (DB 56), disperse yellow (DY 54) of E-type dyes and disperse 92 (DR 92), disperse blue 60 (DB 60), disperse yellow (DY 79) of S-type dyes were used and dyed on jacquard fabrics dependent of dyeing temperature and time. The fastness, dye exhaustion, color strength (K/S value), and colorimetric properties of jacquard fabrics were evaluated. The dyeability of S-type dyes were higher than E-type dyes. The experiments indicated optimum dyeability that the dyeing temperature was $110^{\circ}C$ for E-type dyes and $120^{\circ}C$ for S-type dyes for 40 minutes. The fastness to washing and light were excellent at a 4-5 grade.