• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5051-5059
• /
• 2015

농업용 트랙터 프론트 로더의 낙하정지시험, 코너당김시험, 코너충돌시험의 세 가지 충격시험 조건에 대하여 강체동해석, 과도구조해석, 정적구조해석 등을 수행하여 각 부품의 응력분포를 구하고 안전성을 평가하였다. 낙하정지시험은 프론트 로더를 최대높이에서 시작하여 세 단계로 나누어 낙하시킨 후 정지시켜서 충격을 가하는 경우를 해석하였다. 코너당김시험은 체인으로 버켓 밑면의 모서리를 지면에 구속한 상태에서 프론트 로더를 갑자기 상승시키는 경우를 해석하였다. 코너충돌시험은 주행 중에 버켓의 모서리가 충격장애물과 충돌하는 경우를 해석하였다. 세 가지 충격시험 조건에 대한 해석 결과, 모두 마운트의 사각관 모서리와 마운트의 양쪽 꺾임 위치에서 국부적 응력집중이 발생하였다. 이러한 결과를 바탕으로 새로운 프론트 로더의 설계 및 수정 시 파단에 관한 안전성을 개선하는데 도움이 될 것으로 기대된다.

• Journal of Magnetics
• /
• 제17권1호
• /
• pp.61-67
• /
• 2012

The miniaturization of an electrostatic precipitator has become a key element in successfully constructing an efficient electrostatic precipitator because of the limited space allowed for installation in a subway tunnel. Therefore, the miniaturization of the rapping system of the electrostatic precipitator has also become important. This research proposes a resonant-type electromagnetic vibration exciter as a vibrating rapper for an electrostatic precipitator. The compact vibrating rapper removes collected dust from the collecting plates without direct impact on those collecting plates. To characterize the dynamic performance of the electromagnetic vibration exciter, finite element analysis was performed using a commercial electromagnetic analysis program, MAXEWLL. Moreover, we analyzed the resonant frequency of an electrostatic precipitator, to which the electromagnetic vibration exciter was applied, by ANSYS. Also, to measure the acceleration generated by the electromagnetic vibration exciter, we manufactured a prototype of the ESP and electromagnetic vibration exciter and measured its acceleration at the resonant frequency.

• 한국산학기술학회논문지
• /
• 제6권6호
• /
• pp.542-546
• /
• 2005

연성 크랙의 발생 평가를 위한 J-적분이 충격 하중을 받는 탄소성 3점 굽힘 시험편들에 대하여 연구한다. J-적분을 측정하고 평가하는 실험적인 방법이 연구되었으며 이 결과가 유한 요소법을 이용한 탄소성 이론 해석을 한 값들과 비교하여 거의 일치함을 보였다. 이론적인 수치 해석으로서도 본 연구의 유한 요소 모델로서 J-적분값을 계산할 수 있으며 삼점 굽힘 시험편의 동적 비선형 파괴 실험에 있어서 크랙 입구 개구 변위 (CMOD)에 의하여 J-적분값의 단순 계산이 가능함을 입증하였다. 탄소성 재료의 특성이 여러 가지의 충격 속도들에서 고려된다. J-적분은 충격 실험 동안 얻어진 사진들로부터 직접적으로 측정된 크랙 입구 개구 변위로부터 예측될 수 있다.

• 한국항공우주학회지
• /
• 제30권7호
• /
• pp.44-50
• /
• 2002

본 논문에서는 저속충격을 받는 복합재 샌드위치 평판의 동적 거동에 관한 연구를 수행하였다. 접촉 하중의 산출을 위해서 Hertz의 접촉법칙을 새로이 수정하는 방법을 제시했는데, 지수를 줄이는 방법과 심재의 두께방향의 탄성계수의 값을 줄여 등가 탄성계수를 계산하는 방법을 사용했다. 접촉하중을 산출하는 비선형 방정식은 Newton-Raphson 방법을 사용하여 계산하였고, 시간적분에는 Newmark-beta 방법을 사용하였다. 이러한 기법과 18절점 가정변형률 솔리드 요소를 적용하여 저속충격 해석용 유한요소 프로그램을 개발했다. 이 프로그램을 이용하여 다양한 복합재 샌드위치 평판의 저속충격에 대한 동적 거동을 해석하였다. 제안된 접촉법칙을 적용한 해석결과를 분석하여 볼 때, 대부분의 경우에서 접촉하중과 접촉시간이 실험결과와 대체로 일치함을 확인하였다.

• Computers and Concrete
• /
• 제17권4호
• /
• pp.455-475
• /
• 2016

Dynamic characteristics, named as natural frequencies, damping ratios and mode shapes, affect the dynamic behavior of buildings and they vary depending on the construction stages. It is aimed to present the effects of construction stages on the dynamic characteristics of reinforced concrete (RC) buildings considering theoretical and experimental investigations. For this purpose, a three-storey RC building model with a 1/2 scale was constructed in the laboratory of Civil Engineering Department at Karadeniz Technical University. The modal testing measurements were performed by using Operational Modal Analysis (OMA) method for the bare frame, brick walled and coated cases of the building model. Randomly generated loads by impact hammer were used to vibrate the building model; the responses were measured by uni-axial seismic accelerometers as acceleration. The building's modal parameters at these construction stages were extracted from the processed signals using the Enhanced Frequency Domain Decomposition (EFDD) technique. Also, the finite element models of each case were developed and modal analyses were performed. It was observed from the experimental and theoretical investigations that the natural frequencies of the building model varied depending on the construction stages considerably.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.357-362
• /
• 2011

Air springs are prevalently used as suspension in train. However, air springs are seldom used in automobiles where they improve stability and comfort by enhancing the impact-relief, breaking, and cornering performance. Thus, this study proposed a new method to analyze air springs and obtained some reliable design parameter which can be utilized in vehicle suspension system in contrast to conventional method. Among air spring types of suspension, this study focused on sleeve type of air spring as an analysis model since it has potential for ameliorating the quality of automobiles, specifically in its stability and comfort improvement by decreasing the shock through rubber sleeve. As a methodology, this study used MARC, as a nonlinear finite element analysis program, in order to find out maximum stress and maximum strain depending on reinforcement cord's angle variation in sleeves. The properties were found through uniaxial tension and pure shear test, and they were developed using Ogden Foam which is an input program of MARC. As a result, the internal maximum stresses and deformation according to the changes of cord angle are obtained. Also, the results showed that the Young's modulus becomes smaller, then maximum stresses decrease. It is believed that these studies can be contributed in automobile suspension system.

• 한국해양공학회지
• /
• 제23권1호
• /
• pp.81-88
• /
• 2009

An evaluation of the structural integrity of an oceanographic buoy subjected to extreme loads was carried out in this study. Load components, such as the current, waves, and wind load, which were required for the sea's environmental conditions, were calculated precisely. A non linear finite element analysis was conducted to elucidate the structural response of the buoy under extreme environmental conditions. Based on the surface drift velocity scheme, a dynamic impact analysis was also carried out for the case of collision accidents. The proposed numerical technique would be a useful and cost effective tool for design scheme evaluation in the field of oceanographic buoys.

• 대한건축학회논문집:구조계
• /
• 제34권11호
• /
• pp.3-10
• /
• 2018

Cladding that finishes the exterior of a building could enhance the value of the building, and shape control is an important factor. With the recent development of 3D printing, cementitious claddings were printed by 3D printer in China, U.S.A and elsewhere. On the other hand, the structural safety of the exterior panel should be examined, as casualties occur when the exterior panel fails due to typhoon or impact. Cement-based cladding is reinforced by wire mesh to improve safety. Introducing 3D printing composite system with polymer and cement, makes it possible to produce claddings fast and accurate. Prior to the development of 3D printing cementitious cladding, the major parameters influencing the optimal shape were identified based on structural performance. The wind load, joint, and bond behavior between polymer and cement were considered. Polymer laminate shape, order, and thickness were variables, and finite element analysis was performed.

• Geomechanics and Engineering
• /
• 제29권6호
• /
• pp.645-655
• /
• 2022

Granular columns have recently found widespread use in underground construction. The behaviour of granular columns under vertical loads has been extensively studied, specifically in relation to vertical load capacity obtained by bulging of the column body, including the behaviour after encasement of material. Determining the shear strength of loose soils reinforced with granular columns has received less attention. After the observations of lateral deformation near the toe of the embankment, attempts have been made to strengthen the lateral strength of granular columns. The purpose of this research is to look into the effects of different encasement conditions on the lateral load capacity of granular columns. This was accomplished by three-dimensional finite element analysis with FEM software. Various normal pressures and two different encasement configurations, namely single layer encasement and double layer encasement, with differing tensile strengths, were used in this study to determine their effect on lateral resistance. The failure envelope for a single column planted in loose sand was used to analyse the findings for three different granular column diameters, as well as the impact of different encasement conditions. According to the findings, the inclusion of a Granular Column enhanced the shear strength and overall stiffness of the loose sand bed, and the encasement of the Granular Column helped in deriving higher lateral resistance.

• Advances in Computational Design
• /
• 제8권2호
• /
• pp.97-112
• /
• 2023

The Finite Element (FE) modeling of Reinforced Concrete (RC) under seismic loading has a sensitive impact in terms of getting good contribution compared to experimental results. Several idealized model types for simulating the nonlinear response have been developed based on the plasticity distribution alone the model. The Continuum Models are the most used category of modeling, to understand the seismic behavior of structural elements in terms of their components, cracking patterns, hysteretic response, and failure mechanisms. However, the material modeling, contact and nonlinear analysis strategy are highly complex due to the joint operation of concrete and steel. This paper presents a numerical simulation of a chosen RC column under monotonic and cyclic loading using the FE Abaqus, to assessthe hysteretic response and failure mechanisms in the RC columns, where the perfect bonding option is used for the contact between concrete and steel. While results of the numerical study under cyclic loading compared to experimental tests might be unsuccessful due to the lack of bond-slip modeling. The monotonic loading shows a good estimation of the envelope response and deformation components. In addition, this work further demonstrates the advantage and efficiency of the damage distributions since the obtained damage distributions fit the expected results.