최근 들어 툭별한 물리적 방법을 사용하지 않고 내구성능이 저하된 콘크리트의 성능을 회복시키는 방법의 일환으로서 콘크리트 표면보호재에 대한 관심이 높아지고 있다. 표면보호는 직접적인 의미로서는 콘크리트 구조물의 표면을 보호하는 것뿐만아니라 다양한 열화요인의 침투를 억제함으로서 내부의 콘크리트 및 철근의 열화를 억제하여 콘크리트 구조물을 보호하게 된다. 이와 같은 표면보호재 중 함침계 표면보호재는 콘크리트 표면층의 공극에 충전 혹은 생성물을 석출시켜 치밀한 층으로 하느 충전계와 콘크리트 표면층의 외부 및 내부표면의 성질을 개선하는 표면계로 분류하는 것이 가능하다. 따라서 본 연구는 규플르오르화염을 주성분으로 하는 표면형 함침계 표면보호제 도포에 의한 콘크리트 표면의 세공구조의 변화 및 중성화, 염해, 화학적 침식 등의 내구성 향상을 실험실증적으로 검토함으로서 콘크리트 구조물의 내구성향상 방안을 제시하고자 한다. 그 결과, 표면보호제를 도포함으로서 모든 물시멘트비에서 도포전과 비교하여 전세공용적이 감소하고 있으며, 특히 50nm이상의 비교적 큰 세공경인 모세관공극의 용적이 감소함으로서 물흡수성, 중성화 저항성, 내황산성, 염소이온침투 저항성 등의 내구성 향상에 기여하는 것으로 나타났으며, 그 효과는 물시멘트비가 클수록 높게 나타났다.
Dental ceramics have good aesthetics, biocompatibility, low thermal conductivity, abrasion resistance, and color stability. However poor resistance to fracture and shrinkage during firing process have been limiting factors in their use, particularly in multiunit ceramic restorations. A new method for making all-ceramic crowns that have high strength and low processing shrinkage has been developed and is referred to as the Vita In-Ceram method. This study was performed to investigate the effect of $CeO_2$ addition in borosilicate glasses on the strength of alumina-glass composites. Porous alumina compacts were prepared by slip casting and sintered at $1,100^{\circ}C$ for 2 hours. Dense composites were made by infiltration of molten glass into partially sintered alumina at $1,140^{\circ}C$ for 4 hours. Specimens were polished sequentially from #800 to #2000 diamond disk. and the final surface finishing on the tensile side was received an additional polishing sequence through $1{\mu}m$ diamond paste. Biaxial flexure test was conducted by using ball-on-three-ball method at a crosshead speed of 0.5mm/min. To examine the microstructural aspect of crack propagation in the alumina-glass composites, Vickers-produced indentation crack was made on the tensile surface at a load of 98.0 N and dwell time of 15 sec, and the radial crack patterns were examined by an optical microscope and a scanning electron microscope. The results obtained were summarized as follows; 1. The porosity rates of partially sintered alumina decreased with the rising of firing temperature. 2. The maximum biaxial flexure strength of 423.5MPa in alumina-glass composites was obtained with an addition of 3 mol% $CeO_2$ in glass composition and strength values showed the aspect of decrease with the increase of $CeO_2$ content. 3 The biaxial flexure strength values of alumina-glass composites were decreased with rising the firing temperature. 4. Observation of the fracture surfaces of alumina-glass composites indicated that the enhancement of strength in alumina-glass composites was due to the frictional or geometrical inter-locking of rough fracture surfaces and ligamentary bridging by intact islands of materials left behind the fracture front.
가축사육이 집단화되면서 가축배설물의 축적은 집중화 현상을 초래하게 되었고 또 계속적인 분뇨 분비물의 유출은 환경공해의 요인이 되고 있으며 이는 공공의 걱정거리로 대두되고 있다. 가축분뇨 중에서 질소와 인이 환경공해요인이 되는 가장 중요한 영양소이지만 가축이나 축산시설물에서 발생되는 냄새 역시 공해의 요인이 되고 있다. 급여되는 사료의 영양소효율을 높이는 길이 환경공해를 감소시키는 방법이다. 가장 많은 실험은 닭과 돼지를 대상으로 하여 이루어졌다. 사료첨가제의 이용, 사양방법의 수정 등으로 사료중의 영양소 이용성을 높임으로서 질소와 인의 배출감소는 물론 냄새와 분의 건물함량을 줄일 수 있었다. 1) 합성아미노산 제제를 사료 중에 첨가하고 단백질 수준을 감소시켰을 때 육계의 경우 10∼27%의 질소배출을 기대할 수 있었으며 산란계의 경우 18∼35%, 돼지의 경우 62%, 돼지에서 생성되는 냄새를 9∼43%까지 감소시키는 효과를 기대 할 수 있었다. 2) 사료 중에 효소제를 첨가하였을 때 육계 분의 건물함량을 12∼15% 감소시킬 수 있었다. 3) phytase를 첨가할 경우 분으로 배설되는 인의 함량은 양계의 경우 25∼35%,돼지의 경우 9∼43%까지 감소가 가능했다. 4) 성장촉진제를 이용할 경우 돼지에서 질소의 배설 양을 5∼30% 감소시킬 수 있었으며 냄새는 53∼55%까지 감소가 가능했다. 5) 사료배합을 요구량에 가깝게 하여 급여하였을 때 양계나 양돈의 경우 질소와 인은 각각 10∼15% 감소를 기대 할 수 있었으며 돼지의 냄새는 28∼79%까지 감소가 가능했다. 6) 기별 사양을 철저히 실시함으로서 양계와 양돈의 경우 질소는 10∼33%, 인산은 10∼13%, 그리고 성장 비육돈의 경우 49∼79% 감소를 기대 할 수 있다. 7) 닭이나 돼지의 사료를 배합시 소화율이 높은 곡류를 이용하면 질소와 인의 배설을 5% 감소시킬 수 있다.
본 논문은 경량형강으로 제작한 프레임에 경량기포모르터를 채운 경량합성벽체의 전단 거동에 대한 실험 결과와 전단 강도 및 강성 평가를 제시한 것이다. 경량기포모르터는 스틸하우스 벽체의 구조 성능 및 단열 성능의 향상과 마감에 대한 시공성 개선을 위해 도입되었다. 연구 결과 단열 성능에 대한 기여도는 낮으나, 경량기포모르터의 슬러리 비중이 0.8 이상인 경우 구조 성능의 향상과 마감성이 좋은 것으로 나타났다. 본 연구에서는 전단 거동에 미치는 경량기포모르터의 영향을 알아보기 위해 경량기포모르터의 비중(0.6, 0.8, 1.0, 1.2) 벽체의 스터드 배치간격(450mm, 600mm, 900mm), 마감재(경량기포모르터, OSB, 석고보드) 및 브레이싱 등을 변수로 한 14개의 경량합성벽체를 제작하였고 비교를 위해 대표적인 스틸하우스 벽체 3개를 제작하였다. 면내전단 실험결과, 경량기포모르터를 타설한 경량합성벽체가 기존의 스틸스터드 벽체에 비해 최대 내력은 1.15~5.38배, 초기강성은 1.45~13.7배 증가한 것으로 나타났다. 또한 벽체 내부의 스터드를 900mm까지 확장하여도 무리가 없는 것으로 나타났다. 그러나 이와 같은 결과는 건조수축 균열이 억제되지 않은 상태에서 나온 것으로 경량합성벽체의 내력을 향상시키기 위해서는 경량기포모르터의 초기 건조수축균열을 억제하고 스터드와 경량기포모르터 사이의 부착력을 확보하는 것이 무엇보다도 중요한 것으로 나타났다.
This study was conducted to remove the dyes in dye wastewater by the chemical precipitation or biological treatment which are one of the main pollutants in dye wastewater. In order to remove the disperse dyes effectively in aqueous solution by chemical precipitation process, coagulation and flocculation tests were carried out using several coagulants on various reaction conditions. It was found that the Ferrous sulfate was the most effective coagulant for the removal of disperse dye(DB79), and we could get the best result for the removal of disperse dye(DB56) in the aspects of TOC removal efficiency and sludge yield. When the Ferrous sulfate dosage was 800mg/l, the sludge settling velocity was very fast$(SV_{30}=4\%)$, and the color was effectively removed in the disperse dye(DB79) solution. Although the color removal was ineffective when the Alum was used as a coagulant, the sludge yield decreased in comparison with the Ferrous sulfate or the Ferric sulfate being used in the disperse dye(DB56) solution. In order to decolorize disperse dye(DR17) by using biological treatment process, a strain which has potential ability to degrade disperse dyes was isolated from natural system. The optimal culture conditions of temperature and pH were found to be $40^{\circ}C\;and\;8.5\~9$, respectively. When yeast extract was mixed with polypeptone at the mixing ratio of 1:1 as a nitrogen source, decolorization efficiency was highest$(93\%)$ among the nitrogen sources. The strain screened was excellent to adjust to pH, and it seems to have ability to control pH needed to growth. The optimal culture conditions in concentration of $MgSO_{4.}\cdot7H_2O\;and\;KH_2PO_4$ were $0.1\%(w/v)\;and\;0.2\%(w/v)$, respectively. Strains degrading and decolorizing reactive dyes, RB198 and RR141 which were isolated from water system, are named RBK1 and RRK. And the cell growth characteristics of RBK1 and RRK were investigated. The optimal culture conditions of temperature and pH were found to be 30t' and 7.0, respectively. Optimum nitrogen source was peptone, and it was found that decolorization efficiencies by strains RBK1 and RRK, were $85\%\;and\;62\%$, respectively, with introduction of 4,000mg/l of peptone. In the case of RBK1, color removal efficiencies were very high below 400mg/l. Decolorization efficiency was over $90\%$ at 20hours of culture time. The Color degradation ability of RRK was lower than that of RBK1.
Improvement of heat sink technology related to the continuous implementation performance and extension of device-life in circumstance of easy heating and more compact space has been becoming more important issue as multi-functional integration and miniaturization trend of electronic gadgets and products has been generalized. In this study, it purposed to minimize of decline of the heat diffusivity by gluing polymer through compounding of inorganic particles which have thermal conductive properties. We used NH-9300 as base resin and used inorganic fillers such as silicon carbide(SiC), aluminum nitride(AlN), and boron nitride(BN) to improve heat diffusivity. After making film which was made from 100 part of acrylic resin mixed hardener(1.0 part more or less) with inorganic particles. The film was matured at $80^{\circ}C$ for 24h. Diffusivity were tested according to sorts of particles and density of particles as well as size and structure of particle to improve the effect of heat sink in view of morphology assessing diffusivity by LFA(Netzsch/LFA 447 Nano Flash) and adhesion strength by UTM(Universal Testing Machine). The correlation between diffusivity of pure inorganic particles and composite as well as the relation between density and morphology of inorganic particles has been studied. The study related morphology showed that globular type had superior diffusivity at low density of 25% but on the contarary globular type was inferior to non-globular type at high density of 80%.
The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.
A study was designed to assess the current status of infant feeding and weaning practice through an retrospective survey on feeding method, a period of weaning and various kinds of weaning food. Analysing a few influential environmental factors while assessing the level of knowledge today's mothers have on infant nutrition. The results are as follows: 1. As random samples for this study, a total of 516 mothers having infants under the age of 3 were surveyed. Among them, 235 were from Seoul and 281 were from Kyongi province (Yongin, Suwon, Bupyong, Poil, Kihung, Ansan(Chungbuk)). 2. Among the infants who fell under the category of normality (Kaup index $15{\sim}18$), the infants from Seoul area amounted to 60.7%, surpassing the percentage of the infants from Kyongi province, 41.9%. The percentage of the infants belong to a group of under nutrition (Kaup index <13) was relatively higher than that of the infants in a group of overnutrition (Kaup index >20). 3. 16.1% of mother surveyed were breast-fed, 54.6% were formula-fed and 29.3% were mixed-fed. The result indicated that the percentage of breast-fed infants of high-educated, working mothers were relatively lower than those of low-educated housewives. 4. Most of the respondents knew the significance or the necessity of supplementary food in terms of weaning. 5. 98.8% of those surveyed responded that the mother's adequate knowledge on weaning was necessary. 70.1% of them replied that they wanted to get various and in-depth information in printed materials such as books or other kinds of publications. They, also showed deep interest in recipe of weaning food. 6. The average period when those surveyed began weaning of their infants was $4.3{\pm}1.8$ months. The tendency of earlier weaning in 3 months was founded among 41.1% of them. About half of the respondents, 52.3%, started weaning of their infants in $4{\sim}6$ months. In overall, 93.4% of them set on weaning in less than 6 months after babies were born. The survey, in addition, revealed an interesting fact that earlier weaning of infants was shown in the group of high-educated mothers. 7. According to the study, finishing period of weaning was $13.3{\pm}5.4$ months on average. Only 38.9% of the respondents ended weaning of their infants in 12 months, the proper period recommended by renowned experts. In general, the infants on formula-feeding finished their weaning later than those on breast-feeding (p<0.05).
초고층 복합시설은 수많은 사람들이 이용하고 있는 도심의 핵심시설로서 안전성을 최우선으로 하고 있으며, 화재발생 시 연기와 유독가스는 대형사고를 유발할 수 있다. 본 연구는 초고층 복합시설물에서 화재에 의한 재난이 발생했을 경우, 피난자들이 신속히 안전한 곳으로 피할 수 있는 비상 대피통로용 접이장치에 적용되는 섬유 스크린 소재를 개발하는 데 목적이 있다. 섬유 스크린 소재 개발 방향은 일반적으로 사용되는 철제 소재와 달리 접이장치 내 롤형태로 장기간 보관 시 하중 부담이 적은 경량일 것과 차염/차연 기능이 우수해야 하며 복사열에 의한 피난자의 영향이 적어야 할 것이다. 이에 대해 난연성이 우수한 원단과 후가공을 조건으로 3종의 섬유 스크린 소재를 선정하여 열수축시험, 접촉열시험, 연소성시험, 난연도시험, 인장강도시험, 인열강도시험을 통해 성능평가를 수행하였다. 그 결과 경량의 원단이라도 후가공을 통해 우수한 성능을 발휘할 수 있으며, 실리콘수지 코팅이 섬유 스크린 소재 성능과 복사열에 의한 대피자의 안전을 확보할 수 있는 것으로 나타났다. 이에 따라 무게와 두께가 상이한 유리섬유 2종과 난연 실리콘수지 4종을 대상으로 코팅을 한 후 연소성시험을 수행하여 최적의 후가공조건을 평가하였다.
목조주택의 골조 및 실내 외 마감용으로 사용되는 침엽수 구조재를 대상으로 방염 방충 보존처리제가 혼합된 약제에 마이크로파 가열 후 열기를 지닌체 침지하여 복합적인 기능화를 부여한 후 목재의 건조 스케줄, 방염 시험에 의한 화재 저항성과 흰개미에 의한 내충해성, 혼합 약제의 침투성 분석을 실시한 결과 마이크로파로 3 kW로 5분 급속 가열된 시험편은 목표 온도 및 함수율을 만족하는 것으로 나타났으며, 인산염과 헤테로고리화합물계가 혼합된 약제에 120분 침지할 경우 가장 높은 중량 증가율을 가지는 것으로 나타났다. 또한 방염 후 처리 물품 시험을 실시한 결과 인산염과 혼합된 약제는 방염기준을 모두 만족하는 것으로 나타났으며, 흰개미 투입 후 7일 사충율을 확인한 결과 인산염과 헤테로고리화합물계 혼합 약제 침투 시험편의 경우 96% 이상 높은 사충율을 나타냄으로서 가장 우수한 특성을 가지는 것으로 나타났다. 목재 내부로 약제 침투성 분석을 실시한 결과 목재 세포내부 전면에 있어 혼합약제가 침투된 것으로 나타나 목재의 방염성 및 방충 저항성 등에서 우수한 성능의 발현은 혼합 약제의 균일한 침투때문으로 판단된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.