• Restorative Dentistry and Endodontics
• /
• 제44권1호
• /
• pp.1.1-1.12
• /
• 2019

Objectives: The aim of this in vitro study was to test the effect of 2 finishing-polishing sequences (QB, combining a 12/15-fluted finishing bur and an EVO-Light polisher; QWB, adding a 30-fluted polishing bur after the 12/15-fluted finishing bur used in the QB sequence) on 5 nanotech-based resin composites (Filtek Z500, Ceram X Mono, Ceram X Duo, Tetric Evoceram, and Tetric Evoceram Bulk Fill) by comparing their final surface roughness and hardness values to those of a Mylar strip control group (MS). Materials and Methods: Twelve specimens of each nanocomposite were prepared in Teflon moulds. The surface of each resin composite was finished with QB (5 samples), QWB (5 samples), or MS (2 samples), and then evaluated (60 samples). Roughness was analysed with an optical profilometer, microhardness was tested with a Vickers indenter, and the surfaces were examined by optical and scanning electron microscopy. Data were analysed using the Kruskal-Wallis test (p < 0.05) followed by the Dunn test. Results: For the hardness and roughness of nanocomposite resin, the QWB sequence was significantly more effective than QB (p < 0.05). The Filtek Z500 showed significantly harder surfaces regardless of the finishing-polishing sequence (p < 0.05). Conclusions: QWB yielded the best values of surface roughness and hardness. The hardness and roughness of the 5 nanocomposites presented less significant differences when QWB was used.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2006년도 추계학술발표대회 논문집
• /
• pp.370-373
• /
• 2006

Lastly, the problem of filling occurs in the process of concealed joint of adjacent components and was seen in joints between the structure and an electrical or mechanical device. Therefore, the dry processing which replaces wet joint was seen in joints between the structure and a door, ones between the structure and a finishing materials, ones between a gypsum board and electrical device, and ones between a water pipe and a tile finishing. And a process of separating the area of jointed parts in order to eliminate the problem of overlap was seen in joints between a door and a finishing material and ones between a gypsum board on the ceiling and a light. Lastly, an analysis of a process of exposing concealed parts indicated that the problem of filling could be applied to joints between the structure and an electrical or mechanical device and ones between a finishing material and a mechanical device. This study sought out methods to apply Environment Friendly Multi Housing Remodeling that allow easy remodeling as part of environment- preserving policies. It also contains basic data useful to implement long-life houses in the future by presenting a comprehensive design standard for them

• 한국염색가공학회지
• /
• 제31권4호
• /
• pp.341-353
• /
• 2019

Quercetin is one of flavonoids widely distributed in the plants and well known to have antioxidants, antiinflammatory, antimicrobial properties. In this study, alginate sponge containing quercetin-encapsulated nanocapsules was prepared by miniemulsion polymerization, dyring/crosslinking method and their bioactive characteristics were investigated. Alginate sponge containing quercetin-encapsulated nanocapsules were evaluated using a field emission scanning electron microscope(FE-SEM), a high performance liquid chromatography, cell viability, DPPH radical scavenging activity and antibacterial activity. The study indicates that alginate sponge containing quercetin-encapsulated nanocapsules had significant antioxidant, antiinflammatory and antibacterial activities. This study suggested that alginate sponge containing quercetin-encapsulated nanocapsules can be a potential candidate for medical materials.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권1호
• /
• pp.47-54
• /
• 2004

In this study, the electrorheological (ER) fluid was used as finishing agent. Since the apparent viscosity can be controlled by an electric field, the ER fluid can be one of efficient materials in finishing processes. To finish small 3-dimensional structures such as the aspherical surface in optical elements, the possible arrangement of a tool, part and auxiliary electrode was described. We examined the influence of the addition of a few abrasive particles on the performance of the ER fluid by measuring yield stress and observed the behavior of abrasive particles in the ER fluid by a CCD camera, which had been also theoretically predicted from the electromechanical principles of particles. On the basis of the above results, the steady flow analysis around the rotating micro tool was performed considering the non-uniform electric field. Finally, borosilicate glass was finished using the mixture of the ER fluid and abrasive particles and material removal with field strength and surface roughness were investigated.

• 한국염색가공학회지
• /
• 제34권3호
• /
• pp.173-184
• /
• 2022

In this study, the TPU film was laminated on an aramid fabric or circular knits in order to implement an air cushion material that can respond to high impact forces in case of a fall and is easy to expand. To increase the bonding strength between the fabric layer and the film layer, a primer layer was formed in two ways: one for thermally bonding and laminating PET film and two for coating and aging hot melt type PUR adhesive. The tensile strength of the aramid air cushion was 2.5 times higher than that of the circular knits, but the tensile elongation of the aramid air cushion was very low compared to that of the circular knits. The tear strength of the aramid air cushion was about twice or more superior to that of the circular knits, the primer treatment method was good at A, and the peel strength was excellent at method A. The aramid air cushion was the lightest in weight. Summarizing the above results, it was best to combine the air cushion material with aramid woven fabric and primer treatment method A to cope with the high impact force applied when falling.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.215-216
• /
• 2012

Emissions of CO₂ occur during the production of cement manufacturing process. During the production of clinker, limestone is mainly calcium carbonate, is heated to produce lime and CO₂ as a by-product. It has a major problem, CO₂ uptake is not considered in concrete carbonation, just focus in CO₂ emission. This study is to develop a simulation model for CO₂ uptakes in concrete structures based on carbonation reduction coefficient considering finishing materials. CO₂ uptakes unit of concrete cubic meter is calculated by CO₂ emissions unit of concrete materials and usage of concrete materials in mix proportion. From the simulation result, CO₂ uptake ratios is 2.04 percent in carbonation models of concrete structure during 40 years.

• 한국세라믹학회지
• /
• 제45권6호
• /
• pp.345-349
• /
• 2008

$TiO_2$ coating ceramic tile for self-cleaning purpose was prepared by the precipitant dropping method using $TiCl_4$ as a precursor. $TiO_2$ film was formed on the ceramic tile by spray-coating technique and heat-treated at $500^{\circ}C$ for 1 h. The size and crystalline structure of $TiO_2$ particles were 15.3 nm and anatase phase. The outdoor exposure tests were conducted and the effects of outdoor exposure test conditions, such as exhaust concentration of contamination materials (test places), the UV light intensity (irradiation direction) and coating amounts of $TiO_2$ on the self-cleaning properties were investigated by the brightness measurements. As a results, self-cleaning property of $TiO_2$ coating tile was affected by the coating amount of $TiO_2$ however, not affected by the UV light intensity included in sun's ray (irradiation direction). $TiO_2$ coating ceramic tile can be utilized for exterior finishing materials because of self-cleaning property of $TiO_2$ coating tile.

• 한국건축시공학회지
• /
• 제11권5호
• /
• pp.452-458
• /
• 2011

활성탄을 혼입한 모르타르의 특성을 분석한 결과 유동성 측면에서는 무치환과 참나무 숯 모두 큰 차이를 보이지 않았고, 강도적인 측면에서는 활성탄을 혼입한 모르타르의 강도가 참나무 숯과 무치환 모르타르에 비해 높게 나타났다. 열적 특성은 치환율이 증가할수록 두 혼화재 모두열전도율이 감소하는 경향을 보여 단열성능이 우수함을 입증하였다. 결과적으로 활성탄을 혼입한 모르타르가 강도와 단열성능이 우수함을 증명하여 기존의 활성탄이 가지고 있는 오염물질 흡착성능과 함께 우수한 건축 마감재로서의 여러 성능이 검증되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.269-274
• /
• 2004

The aims of this study were to Investigate the floor impact noise isolation performance of floating floor with isolation materials and propose the improvement direction of floor impact noise measurement method and evaluation classes using impact ball. Reduction of light-weight impact sound pressure level can be achieved by the finishing materials, such as vinyl finishing material and wooden flooring with isolation materials. Floor impact noise Isolation material which satisfy the properties of the floor impact noise isolation materials cause resonance in the low frequency band and worsen heavy-weight impact sound pressure level. Heavy-weight impact sound level can be reduced by using noise reduction flooring, ceiling and increase of slab thickness. Strong impact force in low frequency bang below 63Hz of bang machine is not similar to human impact source and causes some problem in evaluating heavy-weight impact noise but heavy-weight impact noise measurement and evolution using impact ball which is very similar to human impact is more reliable than bang machine. Correction value on the background noise and sensitivity of residents should be considered on the floor impact noise evaluation classes.

• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.102-107
• /
• 2009

This study has been focused on an effective surface finishing method combining ELID (ELectrolytic In-process Dressing) and MAP (Magnetic Assisted Polishing) for the nano-precision mirror grinding of glass-lens molding mould. ELID grinding is an excellent technique for mirror grinding of various advanced metallic or nonmetallic materials. A polishing process is also required for elimination of scratches present on ELID grinded surfaces. MAP has been used as polishing method due to its high polishing efficiency and superior surface quality. It also presents some techniques for achieving the nanometer roughness of the hard material such as WC-Co, which are extensively used in precision tooling material.