• KIEAE Journal
• /
• 제12권5호
• /
• pp.71-76
• /
• 2012

As reviewed of developments of Korean earth architecture, earth-made buildings have been dwindled gradually since "the new community movement" and earth have been recognized as materials which are not so good to human health and in result, earth-related techniques have been also forgotten. However, recently the earth architecture has been more attracting back many attentions thanks to the people who are interested in health and wellbeing and the earth related techniques or skills got keenly required. The present study has investigated and reproduced earth finishing materials which are based on natural materials as basic stuffs to use them as the finishing materials of the modern earth architecture. For the test, the finishing materials have been divided roughly into sorts of pastes and oils. In case of applying finishing materials onto earth surfaces, the moisture permeability test was conducted to measure a water-absorbing speed, and at the case of using finishing materials for interior works moisture adsorption/desorption test was performed to verify the indoor humidity regulation ability, and further a test to check whether to be stained when contacted with the finishing materials, was conducted. If there is not any stain it might be recognized to be high quality of moisture adsorption/desorption and so seaweed pastes or starches might be used for paste finishing materials and for natural oils, beans are desirable in practical ways. As low-quantity of moisture adsorption materials, linseed oil is most desirable and also beaned water over75% are thought to be useful.

• Journal of Animal Science and Technology
• /
• 제62권3호
• /
• pp.313-320
• /
• 2020

This research was performed to investigate the hypothesis that dietary mono-component protease (PRO) might improve growth performance, nutrient digestibility, and carcass characteristics of growing-finishing pigs. A total of eighty-four pigs [Duroc × (Landrace × Yorkshire), 25.3 ± 2.16 kg initial body weight] were randomly assigned to three dietary treatments (7 replicates/treatment; 2 barrows and 2 gilts/replicate) in a randomized complete block design (block = sex). The dietary treatments were prepared as follows; (1) a positive control (PC) as a typical growing-finishing diet based on corn and soybean meal, (2) PC added with 0.015% of PRO (PCPRO), and (3) a negative control (NC) added with 0.015% of PRO (NCPRO). The NC had a lower concentration of crude protein (CP) compared with PC. The PRO was a commercial product that contained 75,000 protease units/g and derived from Nocardiopsis prasina produced in Bacillus licheniformis. Dietary treatments were offered to pigs during growing and finishing periods. Measurements were growth performance, apparent total tract digestibility (ATTD) of nutrients, and carcass characteristics. The PCPRO and/or NCPRO increased average daily gain (ADG) and gain to feed ratio (G:F) during growing (p < 0.10), finishing (p < 0.05), and growing-finishing periods (p < 0.10) compared with PC. Furthermore, pigs fed PCPRO and NCPRO had higher (p < 0.05) ATTD of CP and energy during growing and/or finishing periods than those fed PC. In conclusion, the supplementation of PRO in diets improved growth performance and protein digestibility of growing-finishing pigs.

• 한국실내디자인학회논문집
• /
• 제21권3호
• /
• pp.111-118
• /
• 2012

The purpose of this study is to focus on living rooms that are preferred as a place for changing space image to the maximum and to find a method how finishing materials are expressed by selecting space with mix & match of many images. The study methods are as follows. First, understand the expressive trend of space images through the precedent studies and magazines, and examine its relationship with finishing materials. Second, select space images based on the contents understood earlier and extract adjective words that represent each space image through an expert survey. Third, find the cases where space images are expressed based on the extracted words and analyze expression methods of finishing materials. The results of the study are as follows. First, it was confirmed that recent space images are actively expressed through finishing materials. Second, space images selected through data related to the trend were classified as modern+natural, modern+traditional, modern+retro, classic+natural, classic+humor, and futurism+natural and 4 adjective words for each space image were extracted. Third, expressive elements of finishing materials were extracted as 'material'. 'texture', 'color', and 'pattern' through the precedent studies. Fourth, expressive methods of finishing materials for each space image could be suggested by analyzing the examples that show mix & match based on the contents extracted earlier. Lastly, it is expected to find various methods that lead space image into finishing materials by evaluating responses and changes in visual perception of residents according to expression of finishing materials based on this study.

• 한국CDE학회논문집
• /
• 제20권3호
• /
• pp.312-319
• /
• 2015

The grinding and furbishing process as the finishing process for molds include the works such as the grinding, buffing, lapping and polishing among others. A finishing tool unit is applied to this finishing process for the burr, lapping, polishing and others of molds. A finishing tool unit can carry out the flexible machining, depending on the machining allowance for objects to be cut on the basis of the instrumental driving mechanism which enables the up, down, left and right floating, which is applied in link with the dedicated cutters and robot machining systems. This study selected the shape to increase the rotatory force of an impeller when air is discharged during the driving of a finishing tool unit, and reflected it to the impeller designing. In addition, the study analyzed each flow velocity and pressure distribution per air pressurization value and finally analyzed the rotating torque to suggest the optimal conditions in designing impellers.

• 소성∙가공
• /
• 제5권3호
• /
• pp.232-238
• /
• 1996

A dynamic mill set-up technique was developed to achieva a more precise roll gap set-up of the finishing mill stands for steel strip rolling. In the conventional mill set-up model the set-up values such as roll gap and roll speed are determined before the sheet bar reached the entry side of the finishing mill train and maintained constant until the strip top end passes through the last stand. In the way however a dynamic set-up logic that gives a way to adjust the roll gap value of the final mill stand for the strip ingoing from the ahead of the front stand was developed and attached to the existing set-up model. The roll gap modification is based on the analysis of the observation in the third stand of the finishing mill train. The dynamic set-up model was proved very effective for the more precise mill set-up and for operational stability in the hot strip finishing mill train.

• 대한기계학회논문집A
• /
• 제25권1호
• /
• pp.47-53
• /
• 2001

Results ar presented of a new process for internal precision finishing of slender fine ceramic pipes using a magnetic field generated by a permanent magnets. For finishing the interior surface of a long pipe, a new type of finishing equipment was developed which can be very easily used in an industrial surrounding. In general, the pipe is so slender that a conventional finishing tool is hardly inserted into the pipe deeply, being impossible to finish. Therefore, a new technology has been considered to finish inside of a slender ceramic pipe by a simple technique. In this experimental, Magnetic Abrasive Machining is applied for the inner surface of silicon nitride fine ceramic pipe using ferromagnetic particles mixed with chromium-oxide powder. It is shown the initial roughness of 2.6㎛ Ry(0.42㎛ Ra) in the inside surface can be precisely finished to the roughness of 0.1㎛ Ry(0.01㎛ Ra). This paper discusses the outline of the processing by the application of magnetic abrasive machining and a few finishing characteristics.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.779-782
• /
• 2000

An internal finishing process by the application of magnetic abrasive machining has been developed as a new technology to obtain a fine inner surface of pipe. In this paper, the finishing process of a non-ferromagnetic pipe by a static magnetic field method is introduced and its finishing characteristics is discussed with effective factors by various experiments. From these experimental results, it is found that the proper suppling quantity of magnetic abrasives per diameter of pipe is important, and the inner surface roughness of pipe is not changed much after certain critical finishing time. As a result of this investigation the 3.2$\mu$m Rmax in inner surface roughness of stainless steel pipe is improved to 0.7$\mu$m Rmax after 6 minutes finishing.

• 대한기계학회논문집A
• /
• 제33권5호
• /
• pp.514-520
• /
• 2009

In configuring an automated polishing system, a monitoring scheme to estimate the surface roughness is necessary. In this study, a precision polishing process, magnetic abrasive finishing (MAF), along with an in-process monitoring setup was investigated. A magnetic tooling is connected to a CNC machining to polish the surface of stavax(S136) die steel workpieces. During finishing experiments, both AE signals and force signals were sampled and analysed. The finishing results show that MAF has nano scale finishing capability (upto 8nm in surface roughness) and the sensor signals have strong correlations with the parameters such as gap between the tool and workpiece, feed rate and abrasive size. In addition, the signals were utilized as the input parameters of artificial neural networks to predict generated surface roughness. Among the three networks constructed -AE rms input, force input, AE+force input- the ANN with sensor fusion (AE+force) produced most stable results. From above, it has been shown that the proposed sensor fusion scheme is appropriate for the monitoring and prediction of the nano scale precision finishing process.

• 한국의류산업학회지
• /
• 제22권1호
• /
• pp.112-118
• /
• 2020

This paper examined the water repellency, water proofing and water vapor permeability of twelve types of woven fabrics for sports wear clothing. Their physical properties were compared and discussed with the fabric structural parameters and surface finishing effect. A water repellent property of 100% was obtained in the coated or laminated water repellent finished fabrics; in addition, cotton/nylon breathable composite fabrics treated with a laminated finishing and with low fabric density showed a 90% water repellency. Water proofing fabric above 6,000 mm H₂O hydraulic pressure was achieved by coated or laminated finishing; however, high density fabric or medium-level coated fabrics exhibited 100% water repellent and low water proofing characteristics. Superior water vapor permeability characteristics with good water repellency and proofing properties were achieved at the 2.5 layered low density and with 0.7 - 0.9 cover factor nylon fabrics treated with hydrophilic laminated finishing. The regression analysis for examining the effects of fabric structural parameters and surface finishing such as coating and laminating to the water vapor permeability exhibited a high determination coefficient of fabric structural parameters of 63.5%; in addition,, main factors among fabric structural parameters appeared to be cover factor and fabric thickness per weight. Coating and Laminating factors exhibited determination coefficient of water vapor permeability parameters of 36.5%.

• 한국염색가공학회지
• /
• 제16권1호
• /
• pp.48-52
• /
• 2004

Diffusion/penetration rates of finishing agents are not a major criterion in the design of low molecular weight finishing agents. However, in the case of polymeric finishing agents, high molecular weights result in large hydrodynamic volumes and diffusion/penetration of the finishing agent into the substrate may become a critical factor in the design of textile finishing agents. Thus the effect of the molecular weight of a model compound, polyethylene glycol, on its diffusion through a cellulose membrane or cotton fabric is studied. Diffusion experiments of polyethylene glycol of molecular weight 400, 1000, 2000, 4600, 8000, and 10000 through cellulose membrane or fabric was carried out in a glass U-tube diffusion apparatus and the half penetration times and the penetration coefficients were determined. Both the half penetration times and the penetration coefficients exhibited a significant change between molecular weight 2000 and 2500 as the molecular weight of polyethylene glycol increased, suggesting that there is a critical molecular weight above which diffusion/penetration becomes difficult. Based on this study on a model compound, it is suggested that polymeric textile finishing agents can be expected to exhibit similar behavior.