• 센서학회지
• /
• 제15권4호
• /
• pp.277-283
• /
• 2006

We presented that fabrication process and characteristics of 3 axes flexible tactile sensor available for normal and shear force fabricated using Si micromachining and packaging technologies. The fabrication processes for 3 axes flexible tactile sensor were classified in the fabrication of sensor chips and their packaging on the flexible PCB. The variation rate of resistance was about 2.1 %/N and 0.5 %/N in applying normal and shear force, respectively. The flexibility of fabricated 3 axes flexible tactile sensor array was good enough to place on the finger-tip.

• PNF and Movement
• /
• 제20권1호
• /
• pp.135-145
• /
• 2022

Purpose: The purpose of this study was to investigate the association between cognitive and motor inhibition by comparing muscle activity and ground reaction force during unplanned gait termination according to reaction time measured through the stop-signal task. Methods: Sixteen young adults performed a stop-signal task and an unplanned gait termination separately. The subjects were divided into fast and slow groups based on their stop-signal reaction time (SSRT), as measured by the stop-signal task. Electromyography (EMG) and ground reaction force (GRF) were compared between the groups during unplanned gait termination. The data for gait termination were divided into three phases (Phase 1 to 3). The Mann-Whitney U test was used to compare spatiotemporal gait parameters and EMG and GRF data between groups. Results: The slow group had significantly higher activity of the tibialis anterior in Phase 2 and Phase 3 than the fast group (p <0.05). In Phase 1, the fast group had significantly shorter time to peak amplitude (TPA) of the soleus than the slow group (p <0.05). In Phase 2, the TPA of the tibialis anterior was significantly lower in the fast group than the slow group (p <0.05). In Phase 3, there was no significant difference in the GRF between the two groups (p >0.05). There were no significant difference between the two groups in the spatiotemporal gait parameters (p >0.05). Conclusion: Compared to the slow group, the fast group with cognitive inhibition suppressed muscle activity for unplanned gait termination. The association between SSRT and unplanned gait termination shows that a participant's ability to suppress an incipient finger response is relevant to their ability to construct a corrective gait pattern in a choice-demanding environment.

• 대한토목학회논문집
• /
• 제28권1B호
• /
• pp.95-109
• /
• 2008

본 연구에서는 LDS 난류응력 모형, Van Rijn의 pick up 함수를 활용하여 일정 경사부에서의 파랑의 이행과 천수, 연이은 쇄파현상, plunging breaker에 후행하는 해저질의 역동적인 부유와 down rush와 후행 파랑에 의한 표사의 재분배를 수치모의 하였다. 이 과정에서 해저질과 소통하는 저면 유체력에 대한 quadratic law를 중심으로 한 기존의 연구 성과들은 정상상태에 기초하여 급속히 가속되고 감속되는 swash 대역의 수리특성을 반영할 수 없다는 결론에 도달하고 이러한 인식에 기초하여 새로운 산출방법이 제시되었다. 새로운 산출방법을 토대로 수치모의하여 비선형 천수과정의 일반적인 특징, 동조 비동조 고차 조화성분으로 전이된 파랑에너지로 인해 상당히 예리하고 왜도된 파형, 파형의 마루로부터 시작되는 물입자 자유낙하, 착수로 인한 커다란 물보라의 형성, 물보라 형성층의 해변으로의 이행, wave finger (Narayanaswamy와 Dalrymple, 2002), swash 대역에서 진행되는 부유사 순환과정, swash 대역에서 처오름으로 인해 부유된 부유사 무리의 off shore 방향으로의 순 이동 등이 비교적 정확히 재현되는 등 상당히 고무적인 결과를 얻을 수 있었다. 이러한 결과는 기존의 Euler 좌표계에서 정의되는 파랑모형과 이동경계 기법의 한계를 뛰어 넘는 것으로 향후 보다 정확한 침식해석이 가능 할 것으로 판단된다.

• 구강회복응용과학지
• /
• 제24권1호
• /
• pp.77-89
• /
• 2008

이 연구의 목적은 원추형 내측 연결 임플랜트 시스템에서 하중조건에 따른 지대주의 침하 및 적합도를 평가하는 것이다. 본 연구에서는 내부 원추형 연결방식의 Alloden implant system (Nei Corp. Korea)의 고정체와 2종류(conventional, FDI)의 지대주를 사용하였다. 임상에서 Alloden 임플랜트는 지대주와 고정체 연결시 처음에 손으로 지긋이 눌러 고정시킨 후 mallet을 이용하여 약 3회정도 타격을 가하여 고정한다. 이때 타격시의 정확한 힘을 측정하여 각 실험군에 적용시켰다. 적용 횟수는 손가락으로 누르는 힘을 1회, mallet으로 타격하는 힘을 3회, 저작력으로 가정한 20kg의 힘을 지대주의 침하가 생기지 않을때까지 각각의 표본에 적용하였다. 그 후 각 단계에 대한 지대주의 침하량을 Vernier caliper를 이용하여 측정하였다. 임플랜트는 불포화 폴리에스터(Epovia, Cray Valley Inc. Korea)에 매몰하여 중합시켰고 모든 표본을 절삭한 후 연마하여 주사전자현미경을 통하여 분석, 평가하였다.

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1741-1747
• /
• 2010

본 연구에서는 원격 조정 매니퓰레이터에 적용할 수 있는 보급형 서비스 로봇 암을 개발하였다. 생체 모방학을 활용하여 새로운 형태의 로봇 손에 대한 개념을 도출하였다. 손가락과 손목은 인체 팔의 근골격에 분석을 통하여 상박에 설치된 와이어와 액추에이터에 의하여 구동된다. DC 모터에 의해 구동되는 스크류-너트 매커니즘을 통하여 구동 케이블에 높은 장력을 발생시킨다. 파지력의 쉬운 제어를 위하여 스크류-너트 메커니즘에 조합 스프링을 적용하였다. 첫 번째 설계에서 손가락 제어 문제, 손가락과 손목 운동의 간섭 문제가 발견되었다. 트리즈의 모순 분석을 통하여 이러한 문제에 대한 해결안을 도출하였다. 두 번째 설계에 대하여 다양한 형태와 무게의 물체에 관하여 파지와 동작 테스트를 시행하였다.

• 한국산업융합학회 논문집
• /
• 제20권3호
• /
• pp.233-243
• /
• 2017

This paper proposes a structure of direct-printed flexible tactile-sensor. These flexible tactile sensors are based on pressure-sensing materials that allow pressure to be measured according to resistance change that in turn results from changes in material size because of compressive force. The sensing material consists of a mixture of multi walled carbon nanotubes (MWCNTs) and TangoPlus, which gives it flexibility and elasticity. The tactile sensors used in this study were designed in the form of array structures composed of many lines so that single pressure points can be measured. To evaluate the performance of the flexible tactile sensor, we used specially designed signal-processing electronics and tactile sensors to experimentally verify the sensors' linearity. To test object grasp, tactile sensors were attached to the surface of the fingers of grippers with three degrees of freedom to measure the pressure changes that occur during object grasp. The results of these experiments indicate that the flexible tactile sensor-based robotic gripper can grasp objects and hold them in a stable manner.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.44-50
• /
• 2009

The characteristics of arc pressure, current density and heat flux distribution are important factors in understanding physical arc phenomena, which will have a marked effect on the penetration, size and shape of a weld in TIG welding. The purpose of this study is to find out the effect of the heat flux on the melting efficiency and penetration shape in TIG welding using the results of the previous investigators. The conclusions obtained permit to draw a proper method which derived the heat flux distributions by arc pressure distribution measurements, but previous researchers calculated heat flux and current distribution with the heat intensity measurements by the calorimetry. Heat flux of Ar gas arc was concentrated at the central part and distributed low from the arc axis to the radial direction, that of He mixing arc was lower than that of Ar gas, and it was wide distributed to radial direction. That showed a similar characteristic with the Nestor's by calorimetry calculated values. Throughout heat flux drawn in this study was discussed melting efficiency and penetration shape on Ar gas and He mixing gas arc.

• 대한인간공학회지
• /
• 제24권4호
• /
• pp.15-21
• /
• 2005

Use of a glove made of materials with a low elasticity decreases the performance of the hand such as agility, dexterity, range of motion, and grip strength. The present study examined if the adverse effects of a low-elastic glove can be reduced by a design which accommodates the changes of hand surface lengths by hand motion. Two glove designs which provide patches of elastic cloth and pleats at the finger joints and knuckle were developed by considering the hand surface length changes, and then compared with two conditions(bare hand and conventional glove design that does not consider the dynamic characteristics of the hand dimensions) in terms of completion time in peg board insertion task, maximum grip strength, discomfort in hand motion, discomfort in force exertion, and overall discomfort by 24 right-handed participants. The test results confirmed that wearing of a glove significantly reduced the agility and grip strength capability of the hand and indicated that the novel designs were effective to lessen the performance decreases compared to the conventional design. Also, of the glove designs, the pleat glove design was found most preferred for both better hand performance and less subjective discomfort.

• 제어로봇시스템학회논문지
• /
• 제15권1호
• /
• pp.99-104
• /
• 2009

This article describes the analysis of stable grasping for multi-fingered robot. An analysis method of stable grasping, which is based on the three-dimensional acceleration convex polytope, is proposed. This method is derived from combining dynamic equations governing object motion and robot motion, force relationship and acceleration relationship between robot fingers and object's gravity center through contact condition, and constraint equations for satisfying no-slip conditions at every contact points. After mapping no-slip condition to torque space, we derived intersected region of given torque bounds and the mapped region in torque space so that the intersected region in torque space guarantees no excessive torque as well as no-slip at the contact points. The intersected region in torque space is mapped to an acceleration convex polytope corresponding to the maximum acceleration boundaries which can be exerted by the robot fingers under the given individual bounds of each joints torque and without causing slip at the contacts. As will be shown through the analysis and examples, the stable grasping depends on the joint driving torque limits, the posture and the mass of robot fingers, the configuration and the mass of an object, the grasp position, the friction coefficients between the object surface and finger end-effectors.

• 한국산업융합학회 논문집
• /
• 제19권2호
• /
• pp.88-94
• /
• 2016

In this paper, we describe a new approch to control method of a four joints-robot gripper for the purpose of parts assemblying. The robot gripper is specifically modeled by using a 3D CAD program (ANSYS), considering artificial grippers, and then the proposed control method is illustrated through the dynamic simulation tool (Adams). Each gripper finger is individually controlled to be located at the optimal positions where the maximal joint torque can be calculated. To verified the effectiveness of the proposed control method, we proposed two cases for the reference position of gripper. By comparing the control performance of two method, the performance of the proposed control method was verified.