• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.1
• /
• pp.52-60
• /
• 1999

Drainage rate in wet-end, which has significant influences on the production capacity, product quality and process economics in papermaking, becomes an important factor in the modern high speed papermaking processes owing to increased level of fines contained in today's pulp materials and increased papermaking system closure. A study was carred out to investigate the influence of beating and fines content on natural and vacuum dewatering using a vacuum drainage tester. Increase in beating and accumulation of fines in the stock decreased natural dewatering, Vacuum dewatering effect, however, increased substantially as beating and fines content were increased. But this increase in vacuum dewatering decreased again when a stock is severely beaten or fines content is greater than 35%. Above this level of fines content, mobile fines migrates to the interstices of the forming web to cause sealing or plugging which restrict fluid movement through the web.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.5
• /
• pp.36-41
• /
• 2008

Multi-ply sheet forming has many advantages including the possibility of using wide range of materials in a given structure, lowering production cost, making higher grammage products and so on. But, incorrect structure of sheet makes flow resistance higher so that it shows poor dewatering in press section. One of major factors that affect sheet structure and dewatering property is fines content in each layer. We, therefore, examined the press dewatering of multi-ply sheet that has the different fines content in each layer and the effect of fines distribution on physical properties of sheet to find a technology for optimum utilization of raw materials. In case of two layered sheet, the sheet which was composed of layers with the different flow resistance showed higher dewatering rate than one which has the same flow resistance. And the more difference in fines content for layers existed, the more dewatering occurred. For three layered sheets, dewatering is mainly dependent on fines content of bottom layer. Strength properties were affected by dewatering degree and multi-ply sheet structure.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.1
• /
• pp.24-29
• /
• 2001

The base paper of corrugated board is mainly produced from Korean old corrugated container (KOCC), and thus the recycling rate of KOCC is very high. However, there is a problem that the pulp quality is very low while the recycling rate of OCC is high. The fines content in KOCC, the main source of the corrugated board, amounts to nearly the half of the total stock, and its formation increases as recycling process repeats due to the hornification of fiber. There have been attempts to improve the drainage property of OCC by increasing the headbox concentration of the paper machine or by applying drainage-promoting polymer additives. However, these conventional methods have problems of weakened paper strength and lowered converting fitness caused by paper formation hindrance. The strength of linerboard could not be increased in case KOCC is used, because hornified OCC pulp can-not be sufficiently refined due to the lowered drainage property caused by fines formation. We studied about a new technique consisting of froth-flotation for fractionating pulp stock into a long fiber portion and fines fraction. This study will be developed in order to enhance the drainage and strength properties of a recycled OCC pulp by selective treatment of flocculant on fractionated OCC Fines.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.3
• /
• pp.37-46
• /
• 2023

In this paper, the physical properties, stress deformation and strength characteristics, density and permeability characteristics of silty sand (SM) by fines content were analyzed through indoor tests. also based on the results of the indoor tests, a compact analysis was performed according to the content of SM, and the applicability of SM ground to the compacted target layer was evaluated by comparing it with the measurement data of the actual problem site. As a result of indoor tests and compression analysis, SM changed its mechanical properties from sandy soil to viscous soil when the fine particle content was 35% or higher, and using field measurement data, SM was found to have a higher compression tendency than direct subsidence. Therefore, the mechanical characteristics of SM above Fc 35% are considered to be similar to that of viscous soil, which is different from the compression characteristics of the tendency of immediate subsidence to conventional sandy soil, so it is necessary to present the mechanical characteristics of SM through further research. The research findings highlight the importance of considering consolidation settlement in silty sand (SM) when evaluating soft soil conditions. These findings can aid in revising criteria for assessing weak ground conditions by providing essential engineering property data based on varying fines content in silty sand.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.3
• /
• pp.101-109
• /
• 2007

In South Korea, many weathered soil slopes are composed of soil mixtures with certain amount of clay fractions in natural soil deposits. Accordingly, it is very important to analyze that effect of the fines on the stability of unsaturated soil slopes. In this study, five different soil types classified by mixture portion of fines were used and experiment on the soil-water characteristic curve tests (SWCC) using GCTS (Geotechnical Consulting and Testing Systems) pressure plate were performed in order to analyze the stability of unsaturated soil slopes. Based on the infiltration analysis which contains SWCC test result by the SEEP/W, it is shown that the increasing rate of the wetting band depth was decreased as the fines content and the relative density were increased. According to the stability analysis result of the unsaturated soil slopes through the SLOPE/W, it is found that the transition from the wetting band depth to the variation of strength parameters which affect the stability of unsaturated soil slopes appears to occur around $10\sim15%$ of clay contents in the mixtures.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.63-79
• /
• 2011

In this study relative density tests of bottom ash and standard sand were carried out. And cyclic triaxial tests for samples with the relative density of 40%, 55%, and 70% were carried out on the basis of the test results. Cyclic triaxial tests were also conducted for fines content with 55% relative density. Residual samples were divided into No.40, No.60, No.60, and No.100, and No.200. In order to avoid crashing that can happen when compaction of the sample is initiated, bottom ash was crushed using the a compact mold. In consideration of the crushing characteristics of each residual samples, the fragmentation rate increased up to 30%, which led to the adjustment of fine-grained amount to 10%, 20%, and 30%. Through the repative triaxial test in accordance with the relative density, resistant characteristics of the liquefaction of bottom ash was analyzed. Test results show that, crushing strength of bottom ash was smaller than that of standard sand, resulting in different liquefaction behavior characteristics. And we could find fines content with maximum resistant characteristics of the liquefaction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2007.09a
• /
• pp.502-513
• /
• 2007

This paper describes the rainfall-induced slope failures caused by infiltration due to prolonged rainfall. The emphasis was on quantifying the effect of fine-grained contents which are influencing on the infiltration rate in the wetting front of initially unsaturated slopes during rainfall. Suction tests by tensiometer were performed for five mixture specimens with varying fine-grained contents and then, numerical analyses for the stability of unsaturated slopes are carried out for different relative densities and mixture portions based on the soil water characteristic curves obtained by GCTS pressure plate. It is shown that the fines are highly influenced on wetting front suction of unsaturated soil slopes. Based on the results, it is found that until 15% fine content is the limit showing different wetting front suction, beyond which the wetting band depth do not affect considerably the stability of unsaturated slopes.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.1
• /
• pp.9-16
• /
• 2024

In order to evaluate the relationship between the ground confining pressure and the shear characteristics of the pile-soil interface, this study described the comparative results of the existing experimental results and the FEA results using the strength reduction factor. The strength reduction factor was applied to simulate the shear behavior of the pile-soil interface in finite element analysis(FEA). The analysis results showed that the maximum pullout resistance decreased due to the influence of low confining pressure, as the fines content increased. This trend was similar to the previous experimental research, and this FEA model simulated with the interface strength reduction factor was evaluated as reasonable. The analysis results of the variation in the interface strength reduction factor clearly showed that the interface strength reduction factor clearly increased at a high fines content when the confining pressure was 50kPa. However, it was found that the increase rate was low when the confining pressure was 100kPa and 150kPa. Therefore, confining pressure and fines content need to be considered in FEA to evaluate the shear behavior of the pile-soil interface.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.2
• /
• pp.10-16
• /
• 2004

Structures and strengths of paper have been studied by analyzing fibers characteristics depending on refining methods. Mixing ratio of softwood and hardwood fibers and fibers characteristics have been analyzed for paper quality improvement. In this study flocculation and drainage of fibers were analyzed to improve the production efficiency and paper product's quality. Floc size and drainage rate depending on stock consistency and fines content were analyzed. Total amount of drainage during drainage process was measured quantitatively by using DI(drainage index). Floc size, viscosity of floc and dewatering times were also measured. In the case of refining load $2.8 kg_f$ , drainage was occurred by filtration mechanism rather than thickening mechanism because drainage resistance increased by fibrillation of fibers. Therefore, the drainage rate of $2.8 kg_f$ refining load stock was slower than that of $5.6 kg_f$.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.4
• /
• pp.38-44
• /
• 2007

In order to utilize unsorted ONP, which contains leaflets (printed coated papers), to produce pulp mold, optimum conditions for a repulping process were investigated with a laboratory high consistency pulper. It was concluded that medium or high consistency pulping is necessary to accelerate the rate of deflaking of unsorted ONP. Considering flake content, fines content and pulping energy, the optimum conditions for the laboratory Helico pulper were 11% of repulping concentration and 3 min of repulping time. The repulping temperature shall be at least $30^{\circ}C$. Aging of paper slows down the rate of de flaking but in an actual pulp molding process its effect could be negligible.