• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.151-157
• /
• 2004

Because of the excellent thermal and chemical properties of mullite and cordierite as the stable oxide ceramic materials, they were widely used from engineering materials to electronic materials. Notwithstanding of their high demands, mullite was synthesised because it is not existed in nature. It is also difficult to produce cordierite of fine powder with high purity due to the narrow range of synthetic temperature. Mullite was synthesised by solid state reaction. However, synthesized mullite has been inhomogeneous. Because of the facts, various synthetic methods have been studied so far including sol-gel method. The purpose of this study is to synthesis mullite and cordierite of fine powder with high purity at the lower temperature by solution-polymerization route using PVA as a polymer carrier, which is an economical method by using low cost materials. As a result, mullite and cordierite were produced with mono crystal phase at 1200$^{\circ}C$ and 1250$^{\circ}C$, respectively, and their surface area over 20 ㎡/g.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.89-96
• /
• 1999

Manufacturing conditions of the porous alumina mold were established to overcome various limits of the gypsum mold. For the preparations of the porous alumina mold, an activated charcoal was added to the Al2O3 with the wt% variation and then mixed. The binary slurry was study dispersed based on the examination of the ESA and rheological behaviro. The cylinder type alumina mold was cast in the gyspum mold and characterized by the shrinkage rate at the variable sintering temperature and the resistance against wear. It was proper to make a sintering of the Al2O3 by the surface diffusion which was non-shrinkage sintering mechansim, and intergranular neck growed stronger while sintering was being made. We studied a sintering by three categories; 1) thermodynamic method below 1,000$^{\circ}C$, 2) kinetic method above 1,000$^{\circ}C$ and 3) combined method. In the results of the respective works, combined method was superiro to the others. The prepared Al2O3 mold had relatively high strength, low drying rate, the resistance against the acid or base and good casting behavior.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.263-268
• /
• 1999

In this study, a new concept of aluminum-matrix composites and the possibility of in-situ processing are suggested, and preliminary results on AI- Ti system are presented. Fine powders of AI-lO% Ti were prepared by the gas atomization so that fine $Al_3Ti$ formed into flake shape. A 25v/o $Al_3Ti/Al$ composite sample was made by the pow­d er metallurgy process involving hot extrusion. Microstructure and mechanical behavior both at room temperature and high temperatures were analysed by OM, SEM, TEM and tension test. Microstructural characteristics and mechanical properties of the composites exhibited similar behavior to those of $SiC_w/2124$ composites. Merits and drawbacks of the $Al_3Ti/Al$ composites are discussed together with a possibility of further improvement.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.57-61
• /
• 1997

Formation of fluorite structure and other related crystal structures in the $Y_{0.8}Ta_{0.2}O_{1.7}$-MO(M=Ba, Sr, Ca and Mg) system has been studied $Ba_2YTaO_6,\;Sr_2YTaO_6$ of cubic perovskite type ordered structure anti $Y_2O_3$ of cubic structure were produced besides the defect fluorite structure when 4 moIob of BaO or SrO was added to $Y_{0.8}Ta_{0.2}O_{1.7}$ When CaO more than 8 nlol"/o was added to $Y_{0.8}Ta_{0.2}O_{1.7}$, monoclinic: $Ca_2YTaO$, and cubic $Y_2O_3$ were pri~tlucecl ;IS this sec:onci phases hesides the main fluorite truc,ture. Smglc phase of fluorite structure \vas 1)roduc:ciI when MgO was added up to 12 mol%, however, MgO appeared as the second phase besides the main fluorire structure when MgO was added more than lti moI0'. Consquently, it is considered rh;it the formation of tluorite structure is related with the formation of the cubic perovskite type ordered structure of $A_2(B'B")O_6$ as well as the cation radii of the additives.additives.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.337-341
• /
• 2012

Mechanochemical processing (MCP) involves several high-energy collisions of powder particles with the milling media and results in the increased reactivity/sinterability of powder. The present paper shows results of mechanochemical processing (MCP) of silicon nitride powder mixture with the relevant sintering additives. The effects of MCP were studied by structural changes of powder particles themselves as well as by the resulting sintering/densification ability. It has been found that MCP significantly enhances reactivity and sinterability of the resultant material: silicon nitride ceramics could be pressureless sintered at $1500^{\circ}C$. Nevertheless, a degree of a silicon nitride crystal lattice and powder particle destruction (amorphization) as detected by XRD studies, is limited by the specific threshold. If that value is crossed then particle's surface damage effects are prevailing thus severe evaporation overdominates mass transport at elevated temperature. It is discussed that the cross-solid interaction between particles of various chemical composition, triggered by many different factors during mechanochemical processing, including a short-range diffusion in silicon nitride particles after collisions with other types of particles plays more important role in enhanced reactivity of tested compositions than amorphization of the crystal lattice itself. Controlled deagglomeration of $Si_3N_4$ particles during the course of high-energy milling was also considered.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.287-292
• /
• 2015

The possibility of chemical precipitation for recycled ammonium paratungstate (APT) was studied. WO₃ particles were synthesized by chemical precipitation method using a 1:2 weight ratio of APT:DI-water. At the 500℃ sintering temperature, the X-ray diffraction results showed that APT completely decomposed to WO₃. For the granulated powder WC-Co, vacuum heat treatment at proper temperatures increases tap density and flow-ability. Hardness of the WC-Co thermal spray coating layer was measured in the range HV 831~1266. Spray conditions for the best characteristic values were an oxygen flow rate=1500 scfh, a fuel flow rate = 5.25gph and a gun distance = 320mm.

• Korean Journal of Materials Research
• /
• v.10 no.5
• /
• pp.364-368
• /
• 2000

SiC fiber reinforced $Si_3N_4$ matrix composites combined with electrical conductive phases of carbon fiber and WC powder fabricated by hot pressing at 1773K. The ability to predict fracture in the ceramic matrix composites was evaluated by measuring simultaneous load-deflection and electrical resistanc difference-deflection curves in four point bending tests. The changes in electrical resistance differences closely corresponded to the fracture behavior of the composites. Different electrical conductive phases are suited to predicting different stages and rates of fracture. These obsevations how that it is possible to perform "in situ" fracture detection in ceramic composites.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.525-529
• /
• 2003

Biotribological properties, such as wear rate and friction coefficient, of 3Y-TZP and Low Temperature Degradation (LTD) free materials were investigated via a ball(SiC)-on-plate sliding wear test to evaluate the relationship between wear mechanism and phase transformation. Wear test was conducted with a sliding speed of 0.035 m/s at room temperature and at 25$0^{\circ}C$ in air under a normal load of 49 N, respectively. Although friction coefficient of 3Y-TZP was the lowest due to the fine grain size, the highest wear loss and rate were observed due to the debris of monoclinic grains introduced during sliding and their values increased drastically with raising temperature. However, the biotribological properties of LTD-free materials were insensitive to temperature due to the inertness of the phase transformation, suggesting that they may be applicable to the biomechanical parts.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.178-183
• /
• 2016

Ferroelectric relaxor ceramics with $BaTiO_3-NaNbO_3-Bi(Mg_{1/2}Ti_{1/2})O_3$ ternary compositions (BT-NN-BMT) have been prepared by sol-gel powder synthesis and consequent bulk ceramic processing. Through the modified chemical approach, fine and single-phase complex perovskite compositions were successfully obtained. Temperature and frequency dependent dielectric properties indicated typical relaxor characteristics of the BT-NN-BMT compositions. The ferroelectric-paraelectric phase transition became diffusive when NN and BMT were added to form BT based solid solutions. BMT additions to the BT-NN solid solutions affected the high temperature dielectric properties, which might be attributable to the compositional inhomogeneity of the complex perovskite and resulting weak dielectric coupling of the Bi-containing polar nanoregions (PNRs). The temperature stability of the dielectric properties was good enough to satisfy the X9R specification. The quasi-linear P-E response and the temperature- stable dielectric properties imply the high potential of this ceramic compound for use in high temperature capacitors.

• Journal of the Korean Society of Costume
• /
• v.38
• /
• pp.159-178
• /
• 1998

Genres of the modern arts are expanding the overlapping area between the arts ; ceramics and weaving considered as crafts are devel-oped to the ceramic art and the fiber art, re-spectively. This trend has been also applied to the clothing part, which produced several new terms such as‘art to wear’,‘unwearable art’,‘clothing sculpture’and so on. As following this tendency, the unwearable art is dwelling on the boundary of painting, fiber art and scul-pture, and the clothing sculpture comes from the combination of fiber art and sculpture. While Issey Miyake's dress made of bamboo and Foltuny's pleats dress associated with Greek stone-column introduce the sculpture to the functional fashion design, the works of clothing sculpture become the arts by applying the sculpture to the non-functional unwearable art. Although the clothing sculpture is an interesting subject to be studied continuously for its effect on the contemporary clothing part, it is valuable enough as an unwearable art and sculpture respresenting the artist's concept under the circumstance that the boundary between arts and design is no longer clear, i.e., the clothing and the sculpture come across their regions each other. Furthermore, the clothing sculpture has its own value as a metapor exposing idea, feeling and spirit of the artist in the genre of the unwearable art. With a view point of the abstract clothing concept, the clothing sculpture has been taking the role expanding the clothing to the world of fine art.