• Journal of Powder Materials
• /
• v.14 no.3 s.62
• /
• pp.157-164
• /
• 2007

An electron energy loss spectroscopy (EELS) instrument attached on transmission electron microscopy (TEM) becomes a powerful and analytical tool for extracting the noble information of materials using the enhancement of TEM images, elemental analysis, elemental or chemical mapping images, electron energy loss near edge structure (ELNES), and extended energy-loss fine structure (EXELFS). In this review, the principle and applications of EELS which is widely used in material, life, and electronic sciences were introduced.

• Journal of Sericultural and Entomological Science
• /
• v.41 no.2
• /
• pp.108-115
• /
• 1999

An improvement of methods in fibroin hydrolysates preparat significantly enlarges their applications to practical use. Acidic hydrolysis by hydrohloric acid is one of the methods for silk fibroin depolymeriza6tion. A low yield of final product and long time of the process are the demerits of this method. Possibility of preparation of water-soluble silk hydrolysates with more yield and less expenses is investigated in this study. Such possibility is occurred with the increasing tratment temperature and simultaneously decreasing treatment time, concentration of hydrochoric acid respectively, the concentration of sodium hydroxide used for neutraliza6tion of hydolysates after hydrolysis. Colour is decreased in this case and a small amount of activated, too. Protection of hydrolysates against precipitation after neutraliza6tion, and separation and during concentrating process is the other merit of this method. Creamy-coloured insoluble silk powder is the remainder of hydrolyzed fibroin. This is the only the immobiliza6tion of enzymes and other physiological active substances. Fine particles of this powder can be used as additives for artificial diets and cultural media, as well as raw materials for polymer membranes, etc.

• Korean Journal of Materials Research
• /
• v.26 no.3
• /
• pp.109-116
• /
• 2016

To achieve the fabrication of high-quality Ag-coated Cu particles through a wet chemical process, we reported herein pretreatment conditions using an ammonium-based mixed solvent for the removal of a $Cu_2O$ layer on Cu particles that were oxidized in air for 1 hr at $200^{\circ}C$ or for 3 days at room temperature. Furthermore, we discussed the results of post-Ag plating with respect to removal level of the oxide layer. X-ray diffraction results revealed that the removal rate of the oxide layer is directly proportional to the concentration of the pretreatment solvent. With the results of Auger electron spectroscopy using oxidized Cu plates, the concentrations required to completely remove 50-nm-thick and 2-nm-thick oxides within 5 min were determined to be X2.5 and X0.13. However, the optimal concentrations in an actual Ag plating process using Cu powder increased to X0.4 and X0.5, respectively, because the oxidation in powder may be accelerated and the complete removal of oxide should be tuned to the thickest oxide layer among all the particles. Back-scattered electron images showed the formation of pure fine Ag particles instead of a uniform and smooth Ag coating in the Ag plating performed after incomplete removal of the oxide layer, indicating that the remaining oxide layer obstructs heterogeneous nucleation and plating by reduced Ag atoms.

• Journal of Powder Materials
• /
• v.17 no.6
• /
• pp.456-463
• /
• 2010

This paper describes the results of the application of Cr-Diamond-like carbon (DLC) films for efficiency improvement through surface modification of spur gear parts in the hydraulic gear pump. Cr-DLC films were successfully deposited on SCM 415 substrates by a hybrid coating process using linear ion source (LIS) and magnetron sputtering method. The characteristics of the films were systematically investigated using FE-SEM, nano-indentation, sliding tester and AFM instrument. The microstructure of Cr-DLC films turned into the dense and fine grains with relatively preferred orientation. The thickness formed in our Cr buffer layer and DLC coating layer were obtained the 487 nm and $1.14\;{\mu}m$. The average friction coefficient of Cr-DLC films considerably decreased to 0.15 for 0.50 of uncoated SCM415 material. The hardness and surface roughness of Cr-DLC films were measured 20 GPa and 10.76 nm, respectively. And then, efficiency tests were performed on the hydraulic gear pump to investigate the efficiency performance of the Cr-DLC coated spur gear. The experimental results show that the volumetric and mechanical efficiency of hydraulic gear pump using the Cr-DLC spur gear were improved up to 2~5% and better efficiency improvement could be attributed to its excellent microstructure, higher hardness, and lower friction coefficient. This conclusion proves the feasibility in the efficiency improvement of hydraulic gear pump for industrial applications.

• Journal of Pharmaceutical Investigation
• /
• v.26 no.4
• /
• pp.299-308
• /
• 1996

In order to develop the controlled release of a drug from the suppsitories, in vitro drug release and in vivo absorption in rabbits were investigated. Various suppository forms with hollow cavities, into which drugs in the form of fine powder or solid dispersion system(SDS) could be placed, were utilized. The polyvinyl alcohol(PVA) hydrogel as a base, and propranolol HCl(PPH) as a model drug were employed. In vitro drug dissolution studies showed that the dissolved amounts(%) of PPH from PPH-methylcellulose(MC)-SDS and PPH-ethylcellulose(EC)-SDS reached 100% and 63% in 4.5-hours, respectively. In the relative strength test for PVA hydrogel, PVA hydrogel became harder and more rigid when the number of freezing-thawing cycles and the ratio of PVA 2000 were increased. In vitro drug release profile revealed that the release rate(%) of PPH from PPH-EC-SDS and PPH-MC-SDS hollow type suppositories were sustained. The release amount(%) of PPH from PPH-EC-SDS hollow type suppositories was not affected by storage time, but since the use of hydrophilic MC made PPH diffuse into the hydrogel after it absorbed the water of base, the various release patterns were appeared as the storage time went by. In vivo absorption experiments with rabbits showed that PPH-EC-SDS(PPH : EC=1:3) hollow type suppository delayed the absorption of PPH, significantly. The $C_{max}$, $AUC_{0{\rightarrow}8}$ and MRT of PPH powder hollow type suppository were $196.37{\pm}5.63\;ng/ml$, 1105.26 ng/ml/min and 8.66 min, respectively. The $C_{max}$, $AUC_{0{\rightarrow}8}$ and MRT of PPH-EC-SDS(PPH : EC=1:3) were $91.30{\pm]14.14\;ng/ml$, 554.69 ng/ml/min, 235.99 min, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.1
• /
• pp.39-44
• /
• 1998

$LiCoO_2$ powder was synthesized in an aqueous solution by a sol-gel method and used as a cathode active material for a lithium ion rechargeable battery. The layered $LiCoO_2$ powders were prepared by igniting in air for 12 hrs at 600 ℃ $(600-LiCoO_2)$ and 850 ℃ $(850-LiCoO_2)$. The structure of the $LiCoO_2$ powder was assigned to the space group R bar 3 m (lattice parameters a=2.814 Å and c=14.04Å). The SEM pictures of $600-LiCoO_2$ revealed homogeneous and fine particles of about 1 μm in diameter. Cyclic voltammograms (CVs) of $600-LiCoO_2$ electrode displayed a set of redox peaks at 3.80/4.05 V due to the intercalation/deintercalation of the lithium ions into/out of the $LiCoO_2$ structure. CVs for the $850-LiCoO_2$ electrode had a major set of redox peaks at 3.88/4.13 V, and two small set of redox peaks at 4.18/4.42 V and 4.05/4.25 V due to phase transitions. The initial charge-discharge capacity was 156-132 mAh/g for the $600-LiCoO_2$ electrode and 158-131 mAh/g for the $850-LiCoO_2$ electrode at the current density of 0.2 mA/cm2. The cycleability of the cell consisting of the $600-LiCoO_2$ electrode was better than that of the $850-LiCoO_2$. The diffusion coefficient of the $Li^+$ ion in the $600-LiCoO_2$ electrode was calculated as $4.6{\times}10^{-8}\; cm^2/sec$.

• Korean Journal of Metals and Materials
• /
• v.48 no.12
• /
• pp.1047-1055
• /
• 2010

The objective of this study is to investigate the ballistic properties of Zr-based amorphous alloy surface composites fabricated by high-energy electron-beam irradiation. The mixture of Zr-based amorphous powders and $LiF+MgF_2$ flux powders was deposited on a pure Ti substrate, and then an electron beam irradiated this powder mixture to fabricate a one-layer surface composite. A four-layer surface composite, in which the composite layer thickness was larger than 3 mm, was also fabricated by irradiating the deposited powder mixture by an electron beam three times on the one-layer surface composite. The microstructural analysis results indicated that a small amount of fine crystalline particles were homogeneously distributed in the amorphous matrix of the surface composite layer. According to the ballistic impact test results, the surface composite layers effectively blocked a fast traveling projectile, while many cracks were formed at the composite layers, and thus the surface composite plates were not perforated. The surface composite layer containing ductile ${\beta}$ dendritic phases showed a better ballistic performance than the one without dendrites because dendritic phases hindered the propagation of shear bands or cracks.

• Korean Journal of Metals and Materials
• /
• v.47 no.8
• /
• pp.488-493
• /
• 2009

Direct syntheses of bulk $Ti_3Al$ via electro-discharge-sintering (EDS) of a stoichiometric elemental powder mixture were investigated. A capacitor bank of $450{\mu}F$ was charged with three input energies, 0.5, 1.0, and 1.5 kJ. The charged capacitor bank was then instantaneously discharged through 0.3 g of a Ti-25.0 at.%Al powder mixture for consolidation. Complete phase transformation occurred in less than $200{\mu}sec$ by the discharge and a bulk $Ti_3Al$ compact was obtained. Compared with consolidated samples fabricated by conventional methods such as high vacuum sintering and casting, the electro-discharge-sintered $Ti_3Al$ compact shows a very fine microstructure with a hardness value of 425 Hv. Electro-discharge-sintering under a $N_2$ atmosphere successfully modified the surface Ti oxide of the $Ti_3Al$ compact into Ti nitride, which concurred with the synthesis and consolidation of $Ti_3Al$. Complete conversion yielding a single phase $Ti_3Al$ is primarily dominated by the fast solid state diffusion reaction.

• Journal of Powder Materials
• /
• v.30 no.3
• /
• pp.249-254
• /
• 2023

The influence of MgO addition on the densification and microstructure of alumina (Al₂O₃) was studied. Compacted alumina specimens were manufactured using ball-milling and one-directional pressing followed by sintering at temperatures below 1700℃. Relative density, shrinkage, hardness, and microstructure were investigated using analytical tools such as FE-SEM, EDS, and XRD. When the MgO was added up to 5.0 wt% and sintered at 1500℃ and 1600℃, the relative density exhibited an average value of 97% or more at both temperatures. The maximum density of 99.2% was with the addition of 0.5 wt% MgO at 1500℃. Meanwhile, the specimens showed significantly lower density values when sintered at 1400℃ than at 1500℃ and 1600℃ owing to the relatively low sintering temperature. The hardness and shrinkage data also showed a similar trend in the change in density, implying that the addition of approximately 0.5 wt% MgO can promote the densification of Al₂O₃. Studying the microstructure confirmed the uniformity of the sintered alumina. These results can be used as basic compositional data for the development of MgO-containing alumina as high-dielectric insulators.

• Journal of the Korean Society of Food Culture
• /
• v.23 no.4
• /
• pp.479-488
• /
• 2008

Some biological activities such as an electron donating capacity, the contents of total polyphenol compounds and flavonoids, fibrinolytic activity and $\alpha$-glucosidase inhibitory activity have been detected in hot water extracts of Ligularia fischeri and Angelica gigas Nakai. To increase the usefulness of the functional ingredients for prevention and improvement of some metabolic disorders, ethanol-treated hot water extracts of Angelica gigas Nakai were prepared. A hot water extract of Ligularia fischeri has 92% of electron donating capacity, 39.4 mg/g of total polyphenol compounds, 24.8 mg/g of flavonoids and 29.8% of $\alpha$-glucosidase inhibitory activity, but no fibrinolytic activity. A hot water extract of Angelica gigas Nakai has 94.7% of electron donating capacity, 5.8 mg/g of total polyphenol compounds, 2.6 mg/g of flavonoids, 0.48 plasmin units of fibrinolytic activity and no $\alpha$-glucosidase inhibitory activity. However, with partial purification using cold ethanol treatment, the $\alpha$-glucosidase inhibitory activity of Angelica gigas Nakai was increased to 70.5%. Thus, we expected a more useful effect with the use of the addition of a cold ethanol-treated Angelica gigas Nakai extract. The L, b values of cold buckwheat noodles using a mixture of 0$\sim$3% of Ligularia fischeri powder and 0.5% of an ethanol-treated hot water extract of Angelica gigas Nakai were decreased with the addition of an increasing amount of Ligularia fischeri powder. Among the mechanical qualities, only adhesiveness was significantly higher in 3% Ligularia fischeri noodles. From sensory evaluation data, it was determined that these two functional ingredients did not ruin the color, texture, and overall acceptance of the cold buckwheat noodles. A higher amount of the extracts improved the quality of the product with little added cost.