• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.15-20
• /
• 2020

This study aims to investigate injection rate and microscopic spray characteristics of diesel fuel containing fine air bubble (FBD). fine bubble was generated by cavitation theory using bubble generator. Fuel spray was injected into constant volume chamber and visualized by high speed camera. The injection rate data was acquired with bosch tube method. Injection rate of finebubble diesel was very similar with that of diesel. It showed slightly faster injection start by 5 ㎲ attributed to the low viscosity characteristics. In microscopic spray visualization, fine bubble diesel spray showed unsymmetric spray shape compared with diesel spray. It also showed very vigorous spray atomization performance during initial spray development. Improved atomization was also attributed to the low viscosity and surface tension of finebubble diesel fuel.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.4
• /
• pp.1281-1289
• /
• 2019

This study was conducted to evaluate the optimal operating condition of ultra-fine bubble washing machine for removing calcium chloride from road concrete structure. The diameter of the ultra-fine bubble was measured to 196.6 ± 100.6 nm and the ultra-fine bubble concentration was measured to 1.36 × 108 cell/ml. As a result of the performance on the spray device of the washing machine, it was confirmed that the washing efficiency of 93% and 91% appeared at 100cm and 150cm of injection distance at 100bar injection pressure. By increasing the ultra-fine bubble generation cycles from 2 to 6, the chloride removal rate increased from 1% to 7%. As the ultra-fine bubble generation air flow was lowered from 4 ml/min to 0.5 ml/min, it was confirmed that the washing efficiency increased up to 30%. The washing efficiency of ultra-fine bubble water was 25% higher than normal water.

• Journal of the Korea Convergence Society
• /
• v.8 no.12
• /
• pp.1-7
• /
• 2017

This study was conducted to investigate changes in ginsenoside by continuously treating fine bubble, which are mainly used for environmental purification, in 2-year-old ginseng. The ginsenoside content and composition of ginseng leaves and roots were analyzed for 4 months (120 days) after application of Fine bubble. As a result of treatment with common water in leaves, only Re of protopanaxatriol was significantly higher and As a result of treatment with fine buble, it was confirmed that protopanaxadiol Rb1, RC, Rb2 and Rd components were also increased. Especially, the increase of Re and Rb1 resulted in an increase of total ginsenoside. The ratio of PD / PT to ginseng was 0.811 in finebubble treated leaves and 1.28 in root. The fine bubble treatment induced the synthesis of ginsenoside from the roots and resulted in a PD / PT ratio of close to 1. Therefore, this study suggests a method of cultivating high quality ginseng using fine bubble water and suggests possibility of using it as a functional food material which can be used with leaves as well as roots.

• Korean Journal of Plant Resources
• /
• v.30 no.5
• /
• pp.549-555
• /
• 2017

The production of ginseng cultivation is decreasing due to shortage of cultivated land and climate change, so additional methods are needed. Therefore, the physiological and morphological characteristics of finebubble were analyzed by applying them to ginseng cultivation which is the representative crop of Korea. The application of fine bubble water to 2 year old ginseng showed that stem length and leaf were increased, and weight increased as main root increased in root. In particular, it is shown that the weight of roots increases with the increase of leaf size. This is because the total chlorophyll content is high and it is judged to be related to the increase of photosynthesis efficiency. When the results of this study were confirmed, it was confirmed that ginseng cultivation using fine bubbles showed no inhibition of growth of ginseng. According to the results of physiological characteristics and subdividing results, It was confirmed that the growth of about 10% to 15% of the growth was increased and that the growth of ginseng was increased by applying the fine bubble when growing ginseng.

• Korean Journal of Materials Research
• /
• v.32 no.4
• /
• pp.223-229
• /
• 2022

A porous photocatalyst concrete filter was successfully produced to remove NOx, by mixing TiO₂ photocatalyst with lightweight aerated concrete. Ultra Fine Bubbles were used to form continuous pores inside the porous photocatalytic concrete filter, which was mixed via a bubble generation experiment. The optimal mixing condition was determined to be with 4 % of the bubble generation agent B. NO removal specimens were prepared for various photocatalytic loading conditions, and the specimen containing 3 % P-25 removed NO at a concentration of 1.03 µmol in 1 h. The NO removal rate of the porous photocatalytic concrete filter prepared in this study was 10.99 %. This photocatalytic filter performance was more than 9 times the amount of NO removed by a general photocatalytic filter. The porous photocatalyst concrete filter for removing NOx developed in this study can be applied to various construction sites and the air quality can be solved by reducing NOx contributing to the formation of fine particles.

• Journal of the Korea Convergence Society
• /
• v.8 no.8
• /
• pp.191-196
• /
• 2017

This study was conducted to investigate the effect of fine bubble water treatment on the growth of ginseng seedlings. The growth of ginseng seedlings which were treated with general water and fine bubble water was investigated. The above ground part, the growth of leaf was increased by about 10% and the growth of the stem was about 6%, as the ginseng seedlings which were treated with fine bubble water comparing to the ginseng seedlings treated with general water. Root length was increased about 5%, root width was increased about 8%, roots weight was increased about 9%, and dry weight was increased about 7%. This is not because the whole root growth was increased, but the main root growth was increased about 7%. These results suggested that the physical properties of the fine bubble water stimulated the growth of ginseng seedlings. These results are initial study in the case of ginseng seedlings. Therefore, it can be applicable to the 3-5 years old ginseng plants. Further research will be needed to find out the optimal cultivation condition by controlling the dissolved oxygen amount according to the soil condition and the research applied to the ginseng seedlings.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.444-447
• /
• 2007

The free flow of fine bubbles generated by electrolysis and smoke flow in a space enclosed by fire were recently found to show the same tendency thus leading to the introduction of a research technique. The research experimentally models smoke diffusion and flow in parallel and slanted tunnels using the fine hydrogen bubbles generated by electrolysis in a water tank. Visualization laser with wavelength of 532nm and output power of 1000mW is used to visualize effectively the cross section of fine hydrogen bubble flows generated in a model tunnel.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.4
• /
• pp.139-146
• /
• 2015

This paper describes a effect of nano-bubble on removal of complex heavy metals, in order to remove pollutants of soil with copper (Cu) and lead (Pb) based on column test. It was conducted column test considering inflow and fine soil contents condition, and then it was analyzed removal effect of nano-bubble on Cu and Cu/Pb. The test result showed that the removal effect of the nano-bubble was higher than that of distilled water regardless of fine soil contents in case of Cu pollutant, and the removal effect of nano-bubble on heavy metals was found to have a significant impact on Pb than Cu in case of Cu/Pb pollutants. It was also analyzed that engineering properties (like a flow path and permeability) of soil due to void ratio has influenced a significant impact the pollutants removal of nano-bubble. The test results determined that nano-bubble can be applied as a flushing agent for priority target pollutant in complex heavy metals.

• Environmental Engineering Research
• /
• v.19 no.4
• /
• pp.345-354
• /
• 2014

In this paper, effects of physical configurations and operating conditions on bubble column performance were analyzed in terms of bubble hydrodynamic and mass transfer parameters. Bubble column with 3 different dimensions and 7 gas diffusers (single / multiple orifice and rigid / flexible orifice) were applied. High speed camera and image analysis program were used for analyzing the bubble hydrodynamic parameters. The local liquid-side mass transfer coefficient ($k_L$) was estimated from the volumetric mass transfer coefficient ($k_La$) and the interfacial area (a), which was deduced from the bubble diameter ($D_B$) and the terminal bubble rising velocity ($U_B$). The result showed that the values of kLa and a increased with the superficial gas velocity (Vg) and the size of bubble column. Influences of gas diffuser physical property (orifice size, thickness and orifice number) can be proven on the generated bubble size and the mass transfer performance in bubble column. Concerning the variation of $k_L$ coefficients with bubble size, 3 zones (Zone A, B and C) can be observed. For Zone A and Zone C, a good agreement between the experimental and the predicted $K_L$ coefficients was obtained (average difference of ${\pm}15%$), whereas the inaccuracy result (of ${\pm}40%$) was found in Zone B. To enhance the high $k_La$ coefficient and absorption efficiency in bubble column, it was unnecessary to generate numerous fine bubbles at high superficial gas velocity since it causes high power consumption with the great decrease of $k_L$ coefficients.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.633-643
• /
• 2015

In this study, we develop a highly efficient conical-air diffuser that generates fine bubble. By inserting a sufficient number of aerotropic microorganisms with dissolved oxygen from an air diffuser and minimizing the air-channel blockages within the air diffuser, we expect to improve the efficiency and durability of the decomposition process for organic waste. To upgrade the conventional air diffuser, we perform experiments and numerical analysis to develop a conical-type that generates fine bubble, and which is free from nozzle blockage. We complement the air-diffuser design by numerically analyzing the internal air-flow pattern within the diffuser. Then, by applying the diffuser to a mockup bioreactor, we experimentally and numerically study the bubble behavior observed in the diffuser and the 2-phase fluid flow in the bioreactor. The results obtained include statistics of the cord length and increased velocity, and we investigate the mechanisms of the fluid-flow characteristics including bubble clouds. Throughout the study, we systemize the design procedures for the design of efficient air diffusers, and we visualize the fluid-flow patterns caused by bubble generation within the mockup bioreactor. These results will provide a meaningful basis for further study as well as the detection of oxygen transfer and fluid-flow characteristics in real-scale bio-reactors using sets of air diffusers.