• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.41-48
• /
• 2015

In this study, the effect of heat input on weld metal microstructure and the effects of dissimilar weld heat affected zone in quenched and tempered ASTM A517 on the stainless steel AISI 316L is investigated through the optimization of welding parameters. For this purpose, two welding techniques are used, tungsten-conventional gas and pulsed gas with weld wire ER 309MoL with Diameter 2.4 mm. Research showed that the grain size of the heat affected zone in pulsed welding is less compared with conventional welding; weld metal structure is fully austenitic, it has a finer structure in the pulsed method. Additionally, the growth of weld metal adjacent steel A517 is different from steel 316L. Further, investigation showed that the rate of dilution is less in the pulsed method and the impact energy is increased in each three regions of the weld metal and heat affected zones in the pulsed method; the fracture in the weld metal and heat affected zone of steel 316L is quite soft and it is semi-crispy in the heat affected zone of steel A517.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.118-123
• /
• 2004

A formation of aluminum hydroxide by hydrolysis reaction in the water has been studied by using nano aluminum powder fabricated by pulsed wire evaporation(PWE) method. The hydroxide type and morphology depending on temperature and pH were examined by structural analysis. The Boehmite($Al_2O_3$.$H_2O$ or AIO(OH)) was predominantly formed in high temperature region over 4$0^{\circ}C$, while the Bayerite($Al_2O_3$.$H_2O$ or $Al(OH)_3$) below $30^{\circ}C$ of hydrolysis temperature. The Boehmite formation was preferred to the Bayerite in acidic solution in the same hydrolysis temperature. The slowly formed Bayerite phase showed facet crystalline structure, while the fast formed Boehmite was fine fiber with a large aspect ratio of several nm in diameter and several hundred nm in length, and with much larger specific surface area(SSA) than that of Bayerite. The highest SSA was about $420m^2$/g.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.260-265
• /
• 2004

The materials of ship screw propeller are commonly the manganese bronze. The seawater corrosion and cavitation of the screw propeller reduce tire propulsive performance of ship. In screw manufactory, tire corrosion rust of tire screw propeller is removed by a hand grinding. The grinding work makes the dust of the heavy metals from the manganese bronze. The dust makes indoor working environment poor. A friendly-environmental and automatic corrosion removing apparatus was developed for the improvement of screw processing and working environment. The corrosion rust of a screw propeller was remarkably removed by using apparatus. And the screw surface roughness was improved by a blasting effect of the apparatus performance test. Anode polarization curves on jour processing conditions, that is to say, grinding, blasting, wire-brushing, fine sand papering, were confirmed by a potentiostat. Especially, two kinds of medias, alumina and emery, were used in the blasting processing. Then, investigated tire cavitation erosion of specimen. This result proved that tire blasting work has considerably improved the corrosion resistance of a screw propeller.

• The Korean Journal of Physiology
• /
• 제11권2호
• /
• pp.67-71
• /
• 1977

This study was undertaken to investigate the effect of cingulate cortical ablation upon gastric secretion and its components in rats. 23 male rats were divided into the cingulate(N=9) and the operated control(N= 14) groups. Cingulate cortex was ablated through a slit-shaped opening(1 mm in width, 5 mm in length) which was made symmetrically on both sides of, and parallel to, the sagittal suture by removing a bone flap from frontal bone on each side. In the operated control group, the surgical procedure was ended by the removal of the bone flap. Under light ether anesthesia, experimental animals were placed in a restraining jacket of fine mesh wire and gastric juice was collected for 5 hours via a canula which had been inserted through the anterior abdominal wall into the antral portion of the lumen of the stomach. Volume of the gastric juice was measured, and total acid output and free acid output were titrated with 0.04 N NaOH solution by using phenolphthalein and Topfer's reagent at indicator, and chloride ion output was estimated by means of chloridometer. Results obtained were that volume, total acid output, free acid output and chloride ion output of the gastric juice were higher significantly in the cingulate group than in the operated control group. It is inferred from the above results that the cingulate cortex exerts a fascilitatory influence upon gastric secretion and acid output in rats.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 B
• /
• pp.847-849
• /
• 1996

As the power demands increases, one of the most important data is inside electric field of equipment in designing of insulators ami insulated wire for EHV distribution line. So far finite element analysis method is widely used to calculate this electric field. However as the shape of insulator becomes complicated, it is difficult in producing the mesh which suitable the shape. Especially, we have many difficulty that produce dense fine mesh only where the electric field is concentrated. Therefore in this paper, we perform the each conditional analysis of electric field using the Maxwell 3D Simulator to recover this defects. And we try to analyze electric field through the conventional 2 dimensional and 3 dimensional analysis in case of salt contamination on the surface of a insulator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.107-108
• /
• 2007

Overhead transmission lines are completely exposed to the environment. This causes faults in transmission lines due to natural environmental conditions. In some cases, transmission towers are damaged by typhoons and snow, as well as sleet on the transmission lines. It takes a lot of time to repair the damaged towers. For emergency restoration purposes, steel poles are installed to temporarily supply power. Before 2003, emergency restoration steel poles were made of angled steel, which required a large number of beams, bolts, etc. In addition, the foundation of the steel pole and ground wire was constructed using excavation and burial methods, therefore it required a lot of manpower and time to construct temporary transmission lines. In September 2003, typhoon Maemi, whose maximum wind speed was 60m/s, hit Korea. 'Maemi' destroyed transmission lines in the Busan and Geojea area, causing long blackouts. To reduce the recovery time to the damaged transmission lines, self-build based emergency towers were developed. self-build based emergency towers reduced recovery time from 24 hours to 4 hours or less. However, the self-build based emergency tower had no arms, so the temporary transmission lines could only be constructed without curves in line routes. In this paper, solving these self-build based emergency tower limitations, using insulated arms(designed for use with the self-build based emergency tower), shall be explained.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.195-201
• /
• 2009

This paper is concerned with effects of Mn and heat-input on the mechanical properties of EGW welds. Four different kinds of welding consumables were fabricated by varying Mn contents such as 1.3, 1.5, 1.7, 2.0%Mn and each consumable was welded for EGW on four heat-input conditions between 190 and 340 KJ/Cm. Mn contents were decreased as heat-input increases and alloy elements (C, Si, Ti, B, Al) to deoxidize easily also revealed similar tendency to Mn. Their microstructure, Charpy impact property and strength were investigated, and it is found that Charpy impact property and strength exhibit a strong dependence on change of microstructure by Mn contents and heat-input. The increase of Mn contents or the decrease of heat-input made the microstructure fine and increase volume fraction of acicular ferrite, thereby leading to the great improvement of Charpy impact property and strength. In case of single EGW, optimum Mn contents are over 1.7% for the toughness and strength.

• 센서학회지
• /
• 제32권4호
• /
• pp.232-237
• /
• 2023

This paper presents a system for estimating the position of a magnet using a magnetic sensor. An algorithm is presented to analyze the waveform and output voltage values of the magnetic field generated at each position when the magnet moves and to estimate the position of the magnet based on the analyzed data. Here, the magnet is sufficiently small to be inserted into a blood vessel and has a micro-magnetic field of hundreds of nanoteslas owing to the small size and shape of the guide wire. In this study, a highly sensitive magneto-impedance (MI) sensor was used to detect these micro-magnetic fields. Nine MI sensors were arranged in a 3×3 configuration to detect a magnetic field that changes according to the position of the magnet through the MI sensor, and the voltage value output was polynomially regressed to specify a position value for each voltage value. The accuracy was confirmed by comparing the actual position value with the estimated position value by expanding it from a 1D straight line to a 3D space. Additionally, we could estimate the position of the magnet within a 3% error.

• 자원리싸이클링
• /
• 제28권6호
• /
• pp.96-105
• /
• 2019

폐자동차파쇄잔재물(Automobile Shredder Residue, ASR)은 폐차 재활용시 발생되는 최종 폐기물로써 파분쇄, 공기분급, 자력선별 및 정전선별법과 같은 자원처리 공정을 이용하여 선별할 수 있다. 본 연구에서는 유도형 정전선별기를 이용하여 A SR의 선별효율 향상 및 예측을 위한 전도체(구리) 및 비전도체(유리)의 궤적분석이 수행되었다. 전도체의 궤적분석 결과, 0.5와 0.25 mm 조립자 구리선의 모사궤적은 실제궤적과 거의 일치하였다. 반면 0.06 mm 구리선의 관찰궤적은 (-) 전극으로 편향되었다. 이는 입자특성 및 상대습도에 의한 전하량의 영향 때문으로 판단된다. 비전도체의 경우 절연체 유리의 관찰궤적이 전도성 입자들의 궤적과 유사한 특징을 보이면서 (-) 전극으로 편향되었다. 현미경, SEM & EDS 분석결과 유리표면에서 미립의 철과 전도성 유기물과 같은 이물질 발견되었다. 이와 같이 이물질이 부착된 유리는 ASR 재활용을 위한 정전선별시 비철금속의 선별효율을 저하시키는 것으로판단된다. 향후 연구에서 유리에 부착된 이물질 제거를 위한 전처리 기술개발 및 개선된 궤적모사 연구가 요구된다.

• 공업화학
• /
• 제9권7호
• /
• pp.1011-1017
• /
• 1998

$YBa_2Cu_3O_{6+x}(Y123)-Ag$ 초전도 선재를 0/20 wt%의 은(Ag)을 첨가한 발화합성분말과 고상반응분말을 사용하여 플라스틱 압출법으로 제조하였다. 플라스틱 압출법은 분말제조, 플라스틱 paste 제조, 다이 압축, binder 소각 및 소결공정을 포함한다. 양질의 초전도체를 제조하려면 원료물질이 균질하고 미세한 분말이어야 한다. 0/20 wt%를 첨가한 $Y_2O_3-BaCO_3-CuO$ precursor 분말을 발화합성(PS)법과 고상반응(MM)법으로 제조하였다. 원료분말이 Y123 초전도상으로 전이되는 생성속도를 공기중에서 여러온도와 시간별로 반응시켜 알아보았다. 발화합성법으로 제조한 분말이 고상반응법으로 제조한 분말보다 Y123상으로 빠르게 전이되었다. 이것은 PS법으로 제조한 분말이 미세한 크기와 균질한 화학적 조성으로 인해 Y123상으로 빠른 전이를 한 것이기 때문이다. 플라스틱 압출법으로 제조한 Y123-Ag 초전도 선재의 임계전류밀도($J_c$)는 원료분말의 특징에 따라 $150{\sim}230A/cm^2$값을 나타내었다. 은을 20 wt.% 첨가한 발화합성분말로 제조한 선재의 $J_c$는 $230A/cm^2$이었다.