• Applied Microscopy
• /
• v.13 no.1
• /
• pp.49-61
• /
• 1983

Protoplast releasing mechanisms from Trichoderma koningii, fine structures of the released protoplsts, and their regeneration mode were studied by scanning and transmission electron microscopy. Two types of protoplast releasing mechanisms were observed. In one mechanism, cytoplasm emerged through a cell wall pore developed by cell lytic enzymes and formed a spherical protoplast. In the other mechanism, as the cell wall became progressively thinner, the inner cytoplasm partially rounded to form nonspherical bodies which became spherical protoplasts after being released into the enzyme solution. But, these two types of protoplast releasing mechanisms did not seem to be. mutually exclusive but could occur on the same mycelium simultaneously. And it appeared that cytoplasm which did not become a protoplast by the first mechanism could from a protoplast by the second mechanism. The preparations contained two types of protoplasts, released from different sites of the mycelia. Those released from younger mycelia had dense cytoplasm and small vesicles. Those released from the older mycelia had less dense cytoplasm and larger vacuoles. In the case of regeneration, before producing normal mycelia, most of the protoplasts assumed aberrant tube and yeast-like-forms. Normal mycelia were produced at the end of the yeastlike-forms and sometimes in the middle of the aberrant tube.

• Particle and aerosol research
• /
• v.13 no.3
• /
• pp.105-110
• /
• 2017

Real-time measurements of fine particles from stack emission gases are necessary due to the needs of continuous environmental monitoring of PM10 and PM2.5. The porous tube dilutor using hot and cold dilutions was developed to measure fine particles without condensable particles from highly humid emission gases and compared to the commercialized ejector-type dilutor. Particle size distributions were measured at the emission gases from a diesel engine and a coal-fired boiler. The porous tube dilutor could successfully measure the accumulation mode particles including relatively large particles more than $3{\mu}m$ without nuclei particles, while the ejector dilutor detected some condensable particles and could not detect large particles. The porous tube dilutor could successfully remove the already condensed water droplet particles generated by a humidifier in a $30m^3$ chamber.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.6
• /
• pp.3-9
• /
• 2000

The Bell King Songdok the Great tolls magnificient sound that would be a great vehicle which brings all beings to the Sutras. Since 693, there was a magic flute, MANPASIKJUK, which was in existence in Shilla Dynasty that could lull all the evil-wawes, such an plaques, storms, Droughts, Famines and even Enemies. Thus, a sound tube, MANPASIKJUK, was erected in the crown of the Bell Songdok the Great so as to be effective to emit the nominal frequency tone whenever the Bell tolls for the national prosperity and welfare the People. Therefore, the Bell makers tried to fine the transmissibility condition through the sound tubr, several times during 34 years, However, it seems to be unfinished. Ever since, all of the korean Brahman Bell have the sound tubes of MANPASIKJUK, but none is performed their own functions. Here, one of the way to let the function of the sound tube of MANPASIKJUK out in the Bell Songdok the Great is proposed. There are two steps: the 1st is to elongate 18cm to the present length 77cm to fulfill the transmissibility condition for the nominal frequency of sound is emitted through the corrected sound tybe. 2nd step is to rise to 95% of the emission of the tone of nominal frequency, so that an exponential hem with the flare constant 2.8m-1, length 2.259m and the radius of the mouth 1.772m is to be extended to the corrected sound tube.

• Membrane Journal
• /
• v.24 no.3
• /
• pp.177-184
• /
• 2014

Silica membranes with high permeability were prepared using colloidal and polymeric silica sols on a porous stainless steel-tube support by a DRFF and SRFF method. Silica sols were derived with tetraethylorthosilicate (TEOS) by sol-gel method and analyzed with DLS, FE-SEM, and $N_2$ adsorption. The coating of the intermediate layer with colloidal silica sol on the stainless steel-tube support led to a denser surface morphology of the membrane along with a considerable reduction in the number of surface defect. As the polymeric silica sol enclosed the colloidal silica sol with spherical particles during the SRFF method, the separation-layer-coated silica membrane showed a denser surface than the intermediate layer. Moreover, the silica membranes showed high hydrogen gas permeability of $(6.63-9.21){\times}10^{-5}mol{\cdot}m^{-2}{\cdot}s^{-1}{\cdot}Pa^{-1}$ with low $H_2/N_2$ perm-selectivity (2.9-3.1) at room temperatures.

• Particle and aerosol research
• /
• v.18 no.3
• /
• pp.69-77
• /
• 2022

In order to understand the characteristics of fine particles emitted from coal-fired power plant stacks, it is important to analyze the size distribution and components of particles. In this study, particle size distributions were measured using the ejector-porous tube dilution device and an ELPI system at a stack in a coal-fired power plant. Main elemental components of particles in each size interval were also identified through TEM-EDS analysis for the particles collected in each ELPI stage. Particle size distributions based on number and mass were analyzed with component distributions from 0.006 to 10 ㎛. The highest number concentration was about 0.01 ㎛. The main component of the particles consisted of sulfur, which indicated that sulfate aerosols were generated by gas-to-particle conversion of SO2. In a mass size distribution, a mono-modal distribution with a mode diameter of about 2 ㎛ was shown. For the components of PM1.0 (particles less than 1 ㎛), the abundance order was F > Mg > S > Ca, and however, for the components of PM10 (particles less than 10 ㎛), it was in the order of Fe > S > Ca > Mg. The elemental components by particle size were confirmed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.178-189
• /
• 1994

Fine $BaTiO_3$ powder was synthesized from the various starting solution with 0.05 M by ultrasonic spray pyrolysis method. The conditions of synthesis were fixed on flow rate was 0.5 cm/sec, low temperature furnace was $300^{\circ}C$, and high temperatures furnace was $700^{\circ}C$. The formation procedure was investigated directly by SEM with the collected particle from the each reaction step. Also, the trace of particle in reaction tube was researched theoretically. Fine $BaTiO_3$ was synthesized only in the case of nitrate aqueous solution. The synthesized $BaTiO_3$ powder was porous and spherical which was consist of primary particle at the size of 19.1 nm. The formation procedure was as follows : the particle size decreased in drying step and then increased in initial thermal decomposition step. Finally, particle size was decreased to $0.42 {mu}m$. The trace of particle in reaction tube was also theoretically simulated and discussed.

• Environmental Engineering Research
• /
• v.21 no.3
• /
• pp.233-240
• /
• 2016

The research aims to study the different flexible rubber tube diffusers used in urban wastewater treatment processes and aquaculture systems. The experiment was conducted in small-scale aeration tank with different physical properties of the tubes that were used as aerators. The volumetric mass transfer coefficient ($k_La$), oxygen transfer efficiency (OTE) and aeration efficiency (AE) were measured and determined to compare the diffusers. Moreover, the bubble hydrodynamic parameters were analyzed in terms of bubble diameter ($d_B$) and rising velocity ($U_B$) by a high speed camera (2,000 frames/s). Then the interfacial area (a) and liquid-side mass transfer coefficient ($k_L$) can be calculated. The physical properties (tube wall thickness, tensile strength, orifice size, hardness and elongation) have been proven to be the key factor that controls the performance (kLa and OTE). The effects of hardness and elongation on bubble formation, orifice size and a-area were clearly proved. It is not necessary to generate too much fine bubbles to increase the a-area: this relates to high power consumption and the decrease of the kL. Finally, the wall thickness, elongation and hardness associated of the flexible tube diffuser (tube No. 12) were concluded, to be the suitable properties for practically producing, in this research.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.609-613
• /
• 2004

On this study, electrochemical polishing is adapted to ultra-fine surface for semiconductor large radius gas-tube. The system which buffing and electrochemical polishing can be performed simultaneously was constructed in connection with developing exclusive system. Based on existing papers and the research of background, electrode gap and electrolyte flow were fixed. Current density and electrochemical precision time were chosen as variables. On this study, it is objected to find optimal precision condition and precision variables on the in-process electrochemical polishing.

• Journal of the Korean Society of Safety
• /
• v.14 no.3
• /
• pp.48-53
• /
• 1999

It is widely recognized that Hartmann tube for measuring the minimum ignition energy(MIE) of powder. But It requires long time and operational skills for measuring. As a variety of new fine powders are being produced day by day in industry, Japen has been developing a measurement system which employs a new method to create a dust/air mixture in a miniature combustion box. In this system, by vibration, the powder is successively fed downward through a hopper made up of metal mesh, and then it is formed into a thin, certain-like, dust/air mixture. With this new apparatus, three types of powder-Lycopodium, Anthraquinone, and Polyacry-lonitrile-were tested and the data of MIE were compared with those of a conventional apparatus (the Hartmann tube). Two of them agreed satisfactory, but the other, Anthraquinone, showed quite different values. It is guessed that the agglomerations of the powder particles appear because of particle shapes, static-charge and humidity.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.18 no.2
• /
• pp.420-437
• /
• 2024

There are some problems in network traffic classification (NTC), such as complicated statistical features and insufficient training samples, which may cause poor classification effect. A NTC architecture based on one-dimensional Convolutional Neural Network (CNN) and transfer learning is proposed to tackle these problems and improve the fine-grained classification performance. The key points of the proposed architecture include: (1) Model classification--by extracting normalized rate feature set from original data, plus existing statistical features to optimize the CNN NTC model. (2) To apply transfer learning in the classification to improve NTC performance. We collect two typical network flows data from Youku and YouTube, and verify the proposed method through extensive experiments. The results show that compared with existing methods, our method could improve the classification accuracy by around 3-5%for Youku, and by about 7 to 27% for YouTube.