• CDE review
• /
• v.21 no.2
• /
• pp.39-49
• /
• 2015

This paper presents the single objective design optimization of plate-fin heat sink equipped with fan cooling system using Genetic Algorithm. The proper heat sink and fan model are selected based on the previous studies. And the thermal resistance of heat sinks and fan efficiency during operation are calculated according to specific design parameters. The objective function is combination of thermal resistance and fan efficiency which have been taken to measure the performance of the heat sink. And Decision making procedure is suggested considering life time of semiconductor and Fan Operating cost. And also Analytical Model used for optimization is validated by Fluent, Ansys 13.0 and this model give a quite reasonable and reliable design.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2105-2110
• /
• 2004

Plate-fin type recuperators for the gas turbine/fuel cell hybrid power generating system were designed using commercial design software, MUSE. Heat transfer efficiency and total pressure drop in the recuperator were calculated to confirm required recuperator performance. Both counter flow and cross flow type plate-fin recuperators were designed. Results show that the counter flow type has higher efficiency and short core length, but the cross flow type is simpler to construct because the cross flow type does not need additional distributors. Two or three headers for the each recuperator core will be designed and tested to evaluate best header design. The designed recuperators and headers which will be designed later will be constructed, tested, and used in gas turbine/fuel cell hybrid power generating system.

• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.81-87
• /
• 2005

This study is numerical analysis on the increasing temperature characteristics of vaporizer fin for liquefied natural gas with super low temperature. Existing LNG vaporizers use the direct contact heat transfer mode where the extreme super low temperature LNG of $-162^{\circ}C$ flows inside of the tubes and about $20^{\circ}C$air flows on outside of the fin. Recently, the vaporizers with great enhanced performance compared to conventional type have been developed to fulfill these requirements. The vaporizing characteristic of LNG vaporizer with air as heat source has a fixed iced. These characteristic cause a low efficiency in vaporizer, total plant cost and installing space can be increased. The vaporizing characteristics of LNG via heat exchanger with air are analytically studied for an air heating type vaporizer. This study is intended to supply the design data for the domestic fabrication of the thickness and angle vaporizer fin. Governing conservation equations for mass, momentum and energy are solved by STAR-CD based on an finite volume method and SIMPLE algorithm. Calculation parameter is fin thickness, setup angle and LNG temperature. If the vaporization performance of the early stage and late stage of operating is considered, the case of ${\phi}=90^{\circ}$ was very suitable. In this paper was estimated that the heat transfer was most promoted in case of THF=2mm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.6
• /
• pp.608-614
• /
• 2015

Nitrogen oxide(NOx) emission reductions are required to meet the strict emission regulations for environmental protection. Most of the Exhaust Gas Recirculation(EGR) system applied to a diesel engine can relatively decrease the NOx at a low cost, but it has a disadvantage in that the PM generation is promoted due to the hot intake air temperature. Thus, high heat exchange efficiency of the EGR cooler is required for an effective removal of NOx. In this study, heat exchange efficiency for various types of heat exchangers used in EGR cooler was measured under same conditions, and determined best heat exchange performance shape depending on type of heat exchanger.

• Journal of Power System Engineering
• /
• v.21 no.3
• /
• pp.93-101
• /
• 2017

In conventional adsorption chamber, adsorbent is embedded in between heat exchanger fins by wire mesh. This method impedes heat and mass transfer efficiency. So in this study, to improve the heat transfer performance of heat exchanger, a fin-tube exchanger was coated with FAPO (Ferroaluminophosphate) zeolite adsorbent. The fin-tube heat exchanger has a fin pitch of 1.8 mm with a variation of adsorbent coating thickness of about 0.1 mm, 0.15 mm and 0.2 mm. By varying cooling water temperature and chilled water temperature respecively, heat transfer rate and overall heat transfer coefficient were investigated. As a result, the heat transfer rate and overall heat transfer coefficient increase with decreasing cooling water temperature and increasing chilled water temperature. Under the basic conditions, the heat transfer rate of heat exchanger with 0.2 mm coating thickness is 11% and 43% higher than that of 0.1 mm and 0.15 mm, respectively. The overall heat transfer coefficient is $189.1W/m^2{\cdot}^{\circ}C$, it is two times lager than that of 0.1 mm.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.1
• /
• pp.65-73
• /
• 2017

Intercoolers for multi-stage turbocharger of the hydrogen reciprocating engine for HALE UAV are installed for reducing the charged air inlet temperature of the engine. The intercooler is air to air, cross flow, plate-fin type and the fin configuration is offset-strip fin which is referenced from the heat exchanger of the ERAST. Most of HALE UAV's cruising altitude is 60,000 ft and the density of air for this altitude is very low compared to sea level. Therefore the required heat transfer area for the HALE UAV is about three-times bigger than the sea level. Consequently, it is essential to design to meet the required efficiency of intercooler in the range of not excessively growing the weight of the heat exchanger. The quasi-one dimensional heat transfer design/analysis for satisfying the requirement of the engine are written in this paper. The numerical analyses for estimating the coolant flow rate of the engine bay and pressure loss in the header and core are also summarized.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.2
• /
• pp.103-109
• /
• 2012

Fish generates large thrust through an oscillating motion with a compliant joint of caudal fin. The compliance of caudal fin affects the thrust generated by the fish. Due to the flexibility of the fish, the fish can generate a travelling wave motion which is known to increase the efficiency of the fish. However, a detailed research on the relationship between the flexible joint and the thrust generation is needed. In this paper, the compliant joint of a caudal fin is implemented in the driving mechanism of a robotic fish. By varying the driving frequency and stiffness of the compliant joint, the relationship between the thrust generation and the stiffness of the flexible joint is investigated. In general, as the frequency increases, the thrust increases. When higher driving frequency is applied, higher stiffness of the flexible joint is needed to maximize the thrust. The bending angles between the compliant joint and the caudal fin are compared with the changes of the thrust in one cycle. This result can be used to design the robotic fish which can be operated at the maximum thrust condition using the appropriate stiffness of the compliant joint.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.7 s.262
• /
• pp.581-587
• /
• 2007

At present time, LNG demand of the world is increasing and the piping line for NG transportation has been already installed in Korea. The air fm vaporizer is, however, required because of the transportation for remotely local areas. This paper numerically investigates on the heat transfer characteristics of relevant geometric variations of air-fin vaporizer which is heated by air not by sea water. This vaporizer must be designed in consideration of both efficiency and economics because air is relatively a little heat source. In this study, the pipe and the longitudinal fins are fundamental geometric considerations. Main parameters of geometry are the number, the thickness, and the length of the fins. Finally, the results of heat transfer effects are investigated with the characteristics of each parameter variation.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.7
• /
• pp.545-556
• /
• 2021

The financial technology sector is now growing rapidly all over the world, and it has improved the banking system efficiency and customer experience. This research study attempts explicitly to explore the consumer acceptance attitude of FinTech and its products in Pakistan. Technology Acceptance Model was used to assess the entire variable associated with the consumer attitude to adopt new technology. Based on a survey conducted from Pakistan data and by employing the multiple regression analysis, this study proves that the risk involved in FinTech products and services results in less usage of financial technology. The findings of the study also show that the risk should be reduced if banks and other institutes that are involved in financial transactions online must provide security. Moreover, customers are not willing to pay an extra amount for using financial technology. It argues that usefulness helps to change the attitude of banking customers to use financial technology. The attitudes of the customers have a positive relationship with the adoption of financial technology. These results also help guide financial institutions to enhance the adoption of FinTech products. User attitudes must be changed by providing users with more security, less risky applications, and cost-effective products.

• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2125-2138
• /
• 2023

The printed circuit heat exchanger (PCHE) with airfoil fins has the benefits of high compactness, high efficiency and superior heat transfer performance. A novel multi-objective optimization approach is presented to design the airfoil fin PCHE in this paper. Three optimization design variables (the vertical number, the horizontal number and the staggered number) are obtained by means of dimensionless airfoil fin arrangement parameters. And the optimization objective is to maximize the Nusselt number (Nu) and minimize the Fanning friction factor (f). Firstly, in order to investigate the impact of design variables on the thermal-hydraulic performance, a parametric study via the design of experiments is proposed. Subsequently, the relationships between three optimization design variables and two objective functions (Nu and f) are characterized by an improved particle swarm optimization-backpropagation artificial neural network. Finally, a multi-objective optimization is used to construct the Pareto optimal front, in which the non-dominated sorting genetic algorithm II is used. The comprehensive performance is found to be the best when the airfoil fins are completely staggered arrangement. And the best compromise solution based on the TOPSIS method is identified as the optimal solution, which can achieve the requirement of high heat transfer performance and low flow resistance.