• 에너지공학
• /
• 제24권2호
• /
• pp.72-78
• /
• 2015

본 연구에서는 가스 터빈의 효율을 증대시키는데 사용되는 리큐퍼레이터의 성능에 대한 실험적 연구를 수행하였다. 본 연구에서 채택한 리큐퍼레이터는 오프셋 스트립 휜을 가지는 대항류 열교환기이다. 기존에 제시된 상관식 및 이상상태 사이클 해석을 통하여 최적화된 리큐퍼레이터의 형상을 결정하였다. 리큐퍼레이터의 성능을 평가하기 위해 실험연구를 수행하였다. 특히 리큐퍼레이터의 고온부 입구 온도를 변화시키면서 실험을 수행하였다. 또한 실험 결과를 기존에 제시되어 있던 상관식들과 비교를 하였다. 그 결과 압력강하는 실험결과와 상관식이 잘 맞지 않았지만 유용도는 실험결과와 상관식이 잘 일치하는 것을 확인하였다.

• 한국정보전자통신기술학회논문지
• /
• 제7권1호
• /
• pp.20-25
• /
• 2014

차세대 친환경 조명인 LED소자는 온도가 올라갈수록 LED의 발광효율이 떨어지고 $80^{\circ}C$이상 올라갈수록 수명이 감소하고 스펙트럼선의 파장이 본래의 파장보다 장파장 쪽으로 이동하는 Red Shift현상 및 $T_j$ 상승에 따라 광 출력이 감소되는 큰 문제점이 대두되고 있어 열을 최소화 할 수 있는 방열설계 연구가 진행 중이다. COB Type LED의 경우 보드에 LED 칩을 직접 결합시켜 열 저항을 낮췄지만 주거용 13.5W의 경우 방열판을 통해 발열 문제를 해결해야한다. 본 논문에서는 주거용 13.5W COB LED 다운라이트에 맞게 Heat Sink를 설계하고, 그 설계한 Heat Sink와 13.5W COB를 패키징하여 Solidworks flow simulation을 통해 최적의 Fin두께를 선정하여 접촉식 온도계를 사용한 열적 특성을 분석 하고 평가 하였다.

• 에너지공학
• /
• 제23권4호
• /
• pp.189-195
• /
• 2014

신재생에너지 분야 중 특히 태양에너지를 이용하는 분야는 자원의 무한 및 청정성 때문에 그 사용량이 증가 추세에 있다. 우리나라에서 태양열에너지의 이용률이 전체 에너지 사용량 중 아직 미미한 실정이지만, 근래 정부의 정책적 지원에 힘입어 이 분야에 대한 연구가 활발히 이루어지고 있다. 본 연구는 태양열집열기의 형상 변화에 따른 집열효율을 조사하기 위하여 단일진공관 태양열집열기를 이용한 실험 및 이중진공관 태양열집열기와의 비교 실험을 수행하였다. 그 결과, 본 실험장치에서 히트 파이프의 최고온도의 차이로부터 태양열집열기 형상 변화에 따른 집열효율의 변화를 확인할 수 있었다. 또한 본 연구대상 태양열집열기의 히트파이프의 온도가 비교대상 태양열집열기보다 높음에도 불구하고 방열핀의 온도가 낮게 관측되었다. 이것은 본 연구대상의 태양열집열기는 히트파이프 방열부인 헤드부와 방열핀 사이의 접촉저항이 비교대상의 접촉저항보다 크다는 것을 나타내며, 집열효율을 높이기 위해서는 태양열집열기의 여러 부분의 성능개선뿐만 아니라 접촉저항에 의한 집열손실도 감소시켜야 함을 확인할 수 있었다.

• 한국연소학회지
• /
• 제14권3호
• /
• pp.24-28
• /
• 2009

To improve its efficiency, most of the industrial furnace had been used recuperator. However, commonly used metal recuperator is not suitable under condition of temperature higher than $1000^{\circ}C$. The other hand, ceramic recuperator is able to use in high temperature condition. In the present study, the design program based on the basic heat exchanger design theory, and CFD modelling are applied to ceramic recuperator to verify the design results. Using design program to find the optimum design factor on the variation of recuperator condition. The result of this study are as follows : Thinner fin-plate thickness reduces pressure drop and increases heat-transfer rate, However, thin plate or plate with thin thickness(< 5 mm) is difficult to manufacture, due to limited mechanically strength.

• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.19-23
• /
• 2013

This study is concerned with air-conditioning system in use of thermoelectric device. It is introduced that the well designed structures for better cooling & heating performance with high efficiency. And also it is performed that the system performance test of four types trial products for the use of hybrid commercial vehicle. System performance is affected by many component parts, especially heat sink design & power control method. It is applied that dual extrusive fin tube with buffer zone for the effective radiating of circulating liquid in tube. And also it is applied that power supply method with constant-current system. It is attained that system cooling capacity is 1.2kW, COP is 0.95.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 춘계학술대회 논문집(Proceeding of the KOSME 2000 Spring Annual Meeting)
• /
• pp.146-152
• /
• 2000

As an improvement in the standard of living and economic growth the demand for air conditioning equipment is increasing rapidly. Nowadays air conditioning equipments are being used for industry large building house and car. Thess equipments was concentrated on improving heat efficiency of economic aspects while they design heat exchanger for cooling and heating,. These air conditioning equipments using heat exchanger cause a discomfort to user due to generating mist at the beginning of operating. Therefore the user demand air of high class and quality. In this experimental study to acquire elementary data for development of heat exchanger which be able to supply air of high quality that is to say possess a restraint effect of mist generation. We estimate an effect on cooling plate kind supply air velocity supply air temperature cooled plate temperature and supply air relative humidity which have an influence on outlet air condition of heat exchanger.

• 한국분무공학회지
• /
• 제15권4호
• /
• pp.202-207
• /
• 2010

Mist cooling is widely employed as a cooling technique of high temperature surfaces, and it has heat transfer characteristics similar to boiling heat transfer which has the convection, nucleate and film boiling regions. In the present study, mist cooling heat transfer was experimentally investigated for the mist flow impacting on the heated surfaces of mico-fins. The mist flow was generated by supersonic vibration. Experiments were conducted under the test conditions of droplet flow rate, $Q=6.02{\times}10^{-9}{\sim}3.47{\times}10^{-8}\;m^3/s$ and liquid temperature, $T_f=30{\sim}35^{\circ}C$. From the experimental results, it is found that an increase in the droplet flow rate improves mist cooling heat transfer in the both case of smooth surface and surfaces of micro-fins. Micro-fins surfaces enhance the mist cooling heat transfer. Besides, the experimental results show that an increase in the droplet flow rate decrease the heat transfer efficiency of mist cooling.

• 설비공학논문집
• /
• 제15권5호
• /
• pp.337-345
• /
• 2003

In the case of heat exchangers operating under frosting condition, the growth of frost layer causes the heat exchanger to increase the thermal resistance and pressure loss of the air flow. In this paper, a transient characteristic prediction model of the heat transfer for multi inverter heat pump with frosting on its surface was presented taking into account the change of the fin efficiency due to the growth of the frost layer. In this dynamic simulation program, which was peformed for a basic air conditioning system model, such as evaporator, condenser, compressor, linear electronic expansion valve (LEV) and bypass circuit. The theoretical model was driven from the obtained heat transfer coefficient and mass transfer coefficient, independently. And we consider heat transfer performance was only affected by a decrease of the wind flow area. The calculated results were compared with some cases of experiments for frosting conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권4호
• /
• pp.904-911
• /
• 2001

The fuels of water-in-oil emulsion have a potential of reducing PM(Particulate Matter) and NOx emissions, and increasing combustion efficiency in the furnaces and the burners. For making the most of the beneficial of the secondary atomization due to the microexplosion, the water droplets distributed in the oil must have the optimal sizes. The purpose of this paper is to investigate the water droplet size distribution characteristics of the different types of the static mixers. For analysis the size distribution characteristics efficiently, image analysis system wes constructed and an appropriate image processing algorithm was developed. Two kinds of static mixers: Kenics type and RF type, were tested. As a results, RF type static mixer shows a better characteristics in the mean drop size, particularly in the condition of high water content.

• 한국군사과학기술학회지
• /
• 제10권3호
• /
• pp.189-199
• /
• 2007

The present survey paper introduces the research history, characteristics of body and fin shapes, basic principles of various locomotions and propulsion-generation mechanism of aquatic animals in nature, which utilize unsteady flow through a noble mechanism that is different in paradigm from the propulsion generation mechanism of man-made marine vehicles, and so have excellent performance and efficiency. The authors hope that the present paper helps to activate the domestic research interest on the fields of swimming in nature, which is expected to provide great ideas for improvement and innovation of today's marine vehicles.