• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.128-129
• /
• 1993

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.145-145
• /
• 1997

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.237-237
• /
• 2009

Zinc oxide (ZnO) thin film was deposited on Si substrates using polycrystalline (poly) 3C-SiC buffer layer, in which the ZnO film was grown by sol-gel method. Physical characteristics of the grown ZnO film was investigated experimentally by means of SEM, XRD, FT-IR (Furier Transform-Infrared spectrum), and AFM. XRD pattern was proved that the grown ZnO film on 3C-SiC layers had highly (002) orientation with low FWHM (Full width of half maxium). These results showed that ZnO thin film grown on 3C-SiC buffer layers can be used for various piezoelectric fields and M/NEMS applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.444-450
• /
• 2000

We prepared Co-Cr thin film for perpendicular magnetic recording media with facing targets sputtering system(FTS system) which can deposit a high quality thin film in plasma-free state and wide range of working pressure. The effect of sputtering conditions(argon gas pressure and substrate temperature) on the magnetic and the crystallographic characteristic of Co-Cr thin film was investigated. And the variation of perpendicular coercivity with the variation of film thickness was studied. As a result we obtained the high perpendicular coercivity of 1900Oe and the good dispersion angle of c-axis($\Delta$$\theta$$_{50}$) of 5$^{\circ}$on the film thickness of 100nm for the promising recording layer of perpendicular magnetic recording media.c recording media.a.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.120.2-120.2
• /
• 2015

We propose a novel direct writing technique with a femtosecond laser enabling selective modification of not only the morphology of conducting polymer thin films but also the orientation and alignment of the polymer crystal. Surface relief gratings resulting from photoexpansion on P3HT:PCBM and PEDOT:PSS thin films were fabricated by femtosecond laser direct writing. The photoexpansion was induced at laser fluence below the ablation threshold of the thin film. The morphology (size and shape) of photoexpansion could be quantitatively controlled by laser writing parameters such as focused beam size, writing speed, and laser fluence. GIWAX results showed that face-on P3HT crystals were largely increased in the photoexpansion in comparison with pristine region of the thin film. In addition, the face-on P3HTs in the photoexpansion were aligned with their orientation along the polarization of the laser. The micro-RAMAN spectra confirmed that neither chemical composition change nor the polymer chain breaking was observable after femtosecond laser irradiation. We believe that this laser direct writing technique opens a new door to the fabrication of more efficient OPVs via non-contact, toxic-free approach.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.398-400
• /
• 2003

The YMnO$_3$ thin films were prepared on platinized-silicon substrates by chemical solution deposition and annealed at 750 to 85$0^{\circ}C$ for 1 h under various oxygen pressures, from 2 mTorr to 760 Torr. Effects of annealing oxygen pressures on the crystallization behavior and electrical properties of YMnO$_3$ thin films were investigated. Crystallinity and c-axis preferred orientation of YMnO$_3$ thin film were improved by decreasing the oxygen pressure but were deteriorated at extremely low oxygen pressure, 2 mTorr. Leakage current density of the YMn03 thin film decreased as the oxygen pressure decreased. The film annealed at 80$0^{\circ}C$ under 2 Torr, which had the best crystallinity and the highest c-axis preferred orientation. showed the best-developed ferroelectric C-V hysteresis.

• Corrosion Science and Technology
• /
• v.8 no.3
• /
• pp.93-102
• /
• 2009

The direct-current electroetching of high purity aluminum in hot aqueous-chloride solution produces a high density of micrometer-wide tunnels whose walls are made up of the {100} planes and penetrate aluminum in the <100> directions at rates of micrometer per second. In the process of the alternating-current pitting of aluminum, cathodic polarization plays an important role in the nucleation and growth of the pits during the subsequent polarization. The direct-current tunnel etching and alternating-current etching of aluminum are basically related to the formation of poorly crystallized or amorphous passive films. If the passive film forms on the wall, a natural misfit exists between the film and the aluminum substrate, which in turn gives rise to stress in both the film and the substrate. Even though the amorphous films do not have directed properties, their stresses are influenced by the substrate orientation. The films on elastically soft substrate are likely to be less stressed and more stable than those on elastically hard substrate. The hardest and softest planes of aluminum are the {111} and {100} planes, respectively. Therefore, the films on the {111} substrates are most likely to be attacked, and those on the {100} substrates are least likely to be attacked. For the tunnel etching, it follows that the tunnel walls tend to consist of the {100} planes. Meanwhile, the tunnel tip, where active corrosion takes place, tend to be made of four closely packed {111} planes in order to minimize the surface energy, which gives rise to the <100> tunnel etching.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.641-643
• /
• 2003

The ferroelectric properties of PZT(53/47) thin film was investigated by methoxy enthanol solution based on sol-gel method. The thickness of each layer by spincoating 0.25M sol at one time was $0.1{\mu}m$ and crack-free film was formed. $LaNiO_3/Si(100)$ electrode and $Pt/Ti/SiO_2/Si(100)$ electrode was coated by PZT sol at several times. PZT orientation was confirmed as a method of XRD and coercive field(Ec) as well as remnant polarization(Pr) was investigated from hysterisis curve. As a result of XRD analysis, we can know that the orientation of on PZT/LNO/Si(100) is better than on $Pt/Ti/SiO_2/Si(100)$. The remnant polarization(Pr) in LNO electrode was $87.5{\mu}C/cm^2$ and $39.8{\mu}C/cm^2$ in Pt. From this figures, it is investigated that the Pr in LNO electrode was better than in Pt.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.13-16
• /
• 2006

AIN thin films were prepared on amorphous glass and $SiO_2(1{\mu}m)/Si(100)$ substrate by the facing targets sputtering (FTS) apparatus, which can provide high density plasma, a high deposition rate at a low working gas pressure. The AIN thin films were deposited at a different nitrogen gas flow rate ($1.0{\sim}0.3$) and other sputtering parameters were fixed such as sputtering power of 200w, working pressures of 1mTorr and AIN thin film thickness of 800 nm, respectively. The thickness and crystallographic characteristics of AIN thin films as a function of $N_2$ gas flow rate $[N_2/(N_2+Ar)]$ were measured by $\alpha$-step and an X-ray diffraction (XRD) instrument. And the c-axis preferred orientations were evaluated by rocking curve. In the results, we could prepared the AIN thin film with c-axis preferred orientation of about $5^{\circ}$ on substrate temperature R.T. at nitrogen gas flow rate 0.7.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.111-114
• /
• 2003

In order to improve the surface uniformity and the conduction properties of the fabricated YBCO thick films, a system that applies alternating field vertically to the EPD field has been developed for the first time and applied to the electrophoretic deposition process. The applied alternating electric field caused a force to be exerted on each YBCO particle and resulted in a shaking of the particle in the direction of applied electric field, accomplishing a uniform particle orientation. The usual commercial electrical power was used for the vertically applied alternating voltage and the induced electric field was 25-120 V/cm at 60Hz. The thick film fabricated by the method developed in this paper showed better surface uniformity without crack and porosity and improved film characteristics such as critical temperature ($T_{c,zero}$ : 90 K) and critical current density ($2354\;A/cm^2$). Therefore, it is expected that the shaky-aligned electrophoretic deposition method can be used to fabricate superconductor films through a simpler process and at less expense.