• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.34-34
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL′s EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.207-208
• /
• 2000

The temporal response of the electroluminescence (EL) has been studied in the organic electroluminescent devices fabricated with a vacuum-deposited poly(p-phenylene) (PPP) thin film upon the application of a rectangular driving voltage. The blue EL emission arises with a delay time of several hundred nanoseconds and then saturates with the rise time of less than microsecond. The EL delay time is considered as the transit time of holes in the PPP thin film since the hole mobility is much larger than the electron mobility in PPP. The hole mobility is estimated to be ${\sim}$ $1{\times}10^{-5}$ $cm^2/Vs$ in the vacuum-deposited PPP film.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.686-692
• /
• 2000

Tin-doped In2O3 (ITO) films were fabricated using a d.c. magnetron reactive sputteirng of a In-10 wt% Sn alloy target in an Ar and O2 gas mixture. To understand the behavior of the carrier mobility in ITO films with O2 partial pressure, the resistivity, carrier concentration and mobility, film density, and intrinsic stress in the films were measured with O2 partial pressure. It was found experimentally that the carrier mobility increased rapidly as the film density increased. In the ITO film with the density close to theoretical one, the mean free path was the same as the columnar diameter. This indicated that the mobility in ITO films was strongly influenced by the crystall size. However, in the case where the film density was smaller than a theoretical density, the mean free paths were also smaller the columnar diameter. It was analyzed that the electron scattering at pores and holes within the crystalline was the major obstacle for electron conduction in ITO films. The measurement of intrinsic stress in ITO films also made it clear that the density of ITO films was controlled by the bombardment of oxygen neutrals on the growing film.

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.366-370
• /
• 2007

Nano-scopic holes which are distributed densely and uniformly were fabricated on $SiO_2$ surface. Self-assembling resists were used to produce a layer of uniformly distributed parallel poly methyl methacrylate (PMMA) cylinders in a polystyrene (PS) matrix. The PMMA cylinders were degraded and removed by acetic acid rinsing. Subsequently, PS nanotemplates were fabricated. The patterned holes of PS template were approximately $8{\sim}30\;nm$ wide, 40 nm deep, and 60 nm apart. The porous PS template was used as a dry etching mask to transfer the pattern of PS template into the silicon oxide thin film during reactive ion etching (RIE) process. The sizes of the patterned holes on $SiO_2$ layer were $9{\sim}33\;nm$. After pattern transfer by RIE, uniformly distributed holes of which size were in the range of $6{\sim}22\;nm$ were fabricated on Si substrate. Sizes of the patterned holes were controllable by PMMA molecular weight.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.799-804
• /
• 2012

Recently micro-nano structures has widely been reported to improve the performance of waterproof, heat isolation, sound and light absorption in various fields of electric devices such as mobiles, battery, display and solar panels. A lot of micro-sized holes on the surface of thin film provide excellent sound, or heat, or light transmission efficiency more than solid film and simultaneously nano-sized protrusions around micro hole increase the hydrophobicity of the surface of thin film because of lotus leaf effects as generally known previously. In this paper new rapid fabrication process with 355 nm UV laser ablation was proposed to get micro-nano structures on the surface of thin film, which have only been observed at higher laser fluence. Developed thin micro-nano structured film was also investigated the hydrophobic property by measuring the contact angle and demonstrated the possibility to apply to water droplet separation.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.5
• /
• pp.5-10
• /
• 2014

In this paper, the experimental study was carried to investigate the effect of angle of the anti-vortex holes on the film cooling effectiveness on a flat plate. The pressure sensitive paint technique was applied to measure the film cooling effectiveness. Two anti-vortex hole angles of $0^{\circ}$ and $15^{\circ}$ with respect to the primary hole were considered, and the simple cylindrical hole case was also tested. The blowing ratio based on the cylindrical hole was 0.5 and the same flow rate was kept for all anti-vortex hole cases. Results showed that the film cooling effectiveness for the anti-vortex hole cases were much higher than that of the cylindrical case. Among the anti-vortex hole cases, $15^{\circ}$ angle anti-vortex hole case showed higher film cooling effectiveness than that by the $0^{\circ}$ angle anti-vortex hole case.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1851-1865
• /
• 1994

The objective of the present study is to predict the film cooling effectiveness by a row of holes at various injection ratios and injection angles. Numerical calculations have been performed to investigate the characteristics of flow and temperature distributions in a region near the down-stream of injection hole including the region of adverse pressure gradient. The elliptic turbulent 3-dimensional governing equations with variable thermal properties using the low-Reynolds number k-$\bar{varepsilon}$ model was solved by SIMPLE algorithm. The results showed that the presence of adverse pressure gradient and secondary vortex in the region near the downstream of injection hole induces large temperature gradent. The $45^{\circ}$ injection has higher averaged film cooling effectiveness than $60^{\circ}$ injection. But neverthless the $90^{\circ}$ injection has greater deviation from a flat plate than $45^{\circ}$ and $60^{\circ}$ injection, the $90^{\circ}$ injection has higher averaged film cooling effectiveness than $45^{\circ}$ and $60^{\circ}$ injection in the region near the downstream of injection hole.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.746-751
• /
• 2001

We used a cylindrical model which simulates turbine blade leading edge to investigate the effects of free-stream turbulence intensity and blowing ratio on film cooling of turbine blade leading edge. Tests are carried out in a low-speed wind tunnel on a cylindrical model with three rows of injection holes. Mainstream Reynolds number based on the cylinder diameter was $7.1\times10^4$. Two types of turbulence grid are used to increase a free-stream turbulence intensity. The effect of coolant blowing ratio was studied for various blowing ratios. For each blowing ratios, wall temperatures around the surface of the test model are measured by thermocouples installed inside the model. Results show that blowing ratios have small effect on spanwise-averaged film effectiveness at high free-stream turbulence intensity. However, an increase in free-stream turbulence intensity enhances significantly spanwise-averaged film effectiveness at low blowing ratio.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.24-30
• /
• 2011

PC-TEMs (Polycarbonate Track-Etched membranes) were micro-drilled for biomedical applications by ultrafast pulsed laser. The ablation and damage characteristics were studied on PE-TEMs by assuming porous thin membranes. The experiments were conducted in the range of 2.02 $J/cm^2$ and 8.07$J/cm^2$. The ablation threshold and damage threshold were found to be 2.56$J/cm^2$ and 1.14$J/cm^2$, respectively. While a conical shaped drilled holes was made in lower fluence region, straight shaped holes were drilled in higher fluence region. Nanoholes made the membrane as porous material and ablation characteristics for both bulk and thin film membranes were compared.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.10
• /
• pp.98-106
• /
• 1996

A thin film of aluminum for ultra large scale integrated circuits metalization has been deposited on TiN and SiO$_{2}$ substrates by plasma assisted chemical vapor deposition using DMEAA (dimenthylethylamine alane) as a precursor. The effects of plasma on surface topology and growth characteristics were investigated. Thermal CVD Al could not be got continuous films on insulating subsrate such as SiO$_{2}$. However, it was found that Al films could be deposited on SiO$_{2}$ substate without any pretreatments by the hydrogen plasma for pyrolysis of DMEAA. Compared to the thermal CVD, PACVD films showed much better reflectance and resistance on TiN and SiO$_{2}$ substrate. We obtained mirror-like PACVD Al film of 90% reflectance and resistance on TiN and SiO$_{2}$ substrates. We obtained mirror-like PACVD Al film of 90% reflectance on TiN substrate. Excellent conformal step coverage was obtained on submicron contact holes ;by the PACVD blanket deposition.