• Electrical & Electronic Materials
• /
• v.7 no.2
• /
• pp.145-151
• /
• 1994

The multi-dielectric layer SiOz/Si3N4/SiO2(ONO) is used to scale down the memory device. In this paper, the change of composition in ONO layer due to the process condition and the conduction mechanism are observed. The composition of the oxide film grown through the oxidation of nitride film is analyzed using auger electron spectroscopy(AES). AES results show that oxygen concentration increases at the interface between oxide and nitride layers as the thickness -of the top oxide layer increases. Results of I-V measurement show that the insulating properties improve as the thickness of the top oxide layer increases. But when the thickness of the nitride layer decreases below 63.angs, insulating peoperties of film 28.angs. of top oxide and film 35.angs. turn over showing that insulating property of film 28.angs. of top oxide is better than that of film 35.angs. of top oxide. This phenomenon of turn over is thought as the result of generation of surface state due to oxygen flow into nitride during oxidation process. As the thickness of the top oxide and nitride increases, the electrical breakdown field increases, but when the thickness of top oxide reaches 35.angs, the same phenomenon of turn over occurs. Optimum film thickness for scaled multi-layer dielectric of memory device SONOS is estimated to be 63.angs. of nitride layer and 28.angs. of top oxide layer. In this case, maximum electrical breakdown field and leakage current are 18.5[MV/cm] and $8{\times}{10^-12}$[A], respectively.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.438-444
• /
• 1999

The characterization of the reactively sputtered ITO layer on the PET film has been studied. The PEM device has been used to determine the optimum stoichimetry through control of the amount of oxygen incorporated into the alloy target and the optimum operation conditions to produce films with the highest electrical conductivity and visible transparency. The PEP film was pre-treated under the plasma discharge condition to remove the adsorbed gases and to modify the surface morphology. The results revealed that by adjusting the flow rate of oxygen with the spectral intensity of indium target, the composition of plasma gas can be kept constant during the entire deposition period. The resistivity of ITO film obtained was fond to be about 37$\Omega\Box$, and the transmittance of visual range was about 86%.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.951-952
• /
• 2008

This paper proposes a new method for image composition which estimates the rotation angle of human hand and uses the reserved image in real-time camera images. First, we capture a background image and extract a interesting region by background subtraction. Next, we estimate the skin region from the interesting region and calculate the rotation angle of estimated skin region using PCA(Principal Components Analysis). Finally, we composite the reserved image for the calculated rotation angle in camera images. The proposed method can be applied to control the 3D avatar for marker-less augmented reality.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.779-782
• /
• 2012

$CuIn_{1-x}Ga_xSe_2$ (CIGS) thin films are grown on Mo/soda lime glass using a reactive sputtering process in which a Se cracker is used to deliver reactive Se molecules. The Cu and $(In_{0.7}Ga_{0.3})_2Se_3$ targets are simultaneously sputtered under the delivery of reactive Se. The effects of Se flux on film composition are investigated. The Cu/(In+Ga) composition ratio increases as the Se flux increases at a plasma power of less than 30 W for the Cu target. The (112) crystal orientation becomes dominant, and crystal grain size is larger with Se flux. The power conversion efficiency of a solar cell fabricated using an 800-nm CIGS film is 8.5%.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.5
• /
• pp.243-247
• /
• 2010

The micro Vickers hardness and internal stress of Ni-Fe metal thin film synthesized by electrodeposition method at $25^{\circ}C$ were studied as a function of bath composition, and surface microstructure and atomic compositions of thin films were investigated by SEM and EDS. And the shape change of $200\;{\AA}$ Ni-Fe nanowires made using anodic aluminum oxide(AAO) templates by electrodeposition method were observed by SEM as a function of ultrasonic treatment time and bath composition. The Fe deposition contents on the substrate non-linearly increased with Fe ion concentration over total metal ion concentration. In case of low Fe contents film, the grain size is smaller and denser than high Fe contents deposited films, and the micro Vickers hardness increased with Fe contents of electrodeposited films. These results affected the shape change of nanowire after ultrasonic treatments.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.874-879
• /
• 1987

An exact wave-optics analysis of wave propagation in thin-film optical waveguide using gyrotropic materials as the substrate or film of the guide is presented for the first time. Based on the Maxwell's equations and the boundary conditions of the guide, the field composition and the boundary conditions of the guide, the field composition and the phase velocity for the eigenmodes of the guide are determined. The field patterns of the guided waves are shown for the eigenmodes of the guides. The present analysos allows a new interpretation in the mode conversion of the thin-film optical waveguides.

• Journal of the Korean Applied Science and Technology
• /
• v.11 no.2
• /
• pp.17-38
• /
• 1994

Oil and fats has been using as the important raw materials in the coating industry from ancient time to date. This article was prepared with the aim of helping to the forward development trend for coating uses of oil and fats, as understand together the history using oil and fats for coatings, composition and classification coatings, types and composition of oil and fats using for coatings nowaday, how to use oil and fats for coating, film for coatings, film forming mechanism.

• International journal of advanced smart convergence
• /
• v.13 no.2
• /
• pp.136-141
• /
• 2024

Chang'an (Chinese: 长安三万里), also known as 30,000 Miles from Chang'an, is a 2023 Chinese 3D animated historical drama film directed by Xie Junwei and Zou Jing.This thesis aims to explore the visual expression of traditional culture in the 3D animated film Chang'an as an example to reveal the reasons for the success of this type of film. The study analyses in detail the design of the character models and costumes, as well as the use of the traditional landscape painting technique of 'white space' in the composition of the screen from the visual aspect. Through the analysis of character design and screen composition, the thesis concludes that the success of Chang'an lies in its elaborate visual design and clever use of traditional culture, which makes it a 3D animation film with both artistic and commercial values. Finally, the thesis concludes that the production of a successful 3D animation film needs to combine the visual elements of 3D animation with traditional culture in order to win audience recognition and achieve commercial success.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1605-1608
• /
• 2004

Single phase $CuInS_2$ thin film with a highest diffraction peak (112) at a diffraction angle ($2{\theta}$) of 27.7$^{\circ}$ was well made by SEL method at annealing temperature of 250 $^{\circ}C$ and annealing hour of 60 min in vacuum of $10^{-3}$ Torr or in S ambience for an hour. And the peak of diffraction intensity at miller index (112) of $CuInS_2$ thin film annealed in S ambience was shown a little higher about 11 % than in only vacuum. Single phase $CuInS_2$ thin films were appeared from 0.85 to 1.26 of Cu/In composition ratio and sulfur composition ratios of $CuInS_2$ thin films fabricated in S ambience were all over 50 atom%. Also when Cu/In composition ratio was 1.03, $CuInS_2$ thin film with chalcopyrite structure had the highest XRD peak (112). And lattice constant a and grain size of the thin film in S ambience were appeared a little larger than those in only vacuum. The largest lattice constant of a and grain size of $CuInS_2$ thin film in S ambience was 5.63 ${\AA}$ and 1.2 ${\mu}$m respectively. And the films in S ambience were all p-conduction type with resistivities of around $10^{-1}{\Omega}cm$.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.3
• /
• pp.109-115
• /
• 2009

Magnesium is one of the lightest metals, and magnesium alloys have excellent physical and mechanical properties such as high stiffness/weight ratios, good castability, good vibration and shock absorption. However their poor corrosion resistance, wear resistance, hardness and so on, have limited their application. To improve these defects, many techniques are developed. Micro arc oxidation(MAO) is a one of the surface treatments under anodic oxidation in which ceramic coating is directly formed on the surface of magnesium alloy. In this study, the characteristics of anodic film were examined after coating the AZ31B magnesium alloy through the MAO process. MAO was carried out in potassium hydroxide, potassium fluoride, and various concentration of sodium silicate in electrolyte. The morphology and chemical composition of the coating layer were characterized by SEM, XRD, EPMA and EDS. The hardness of anodic films was measured by micro-vickers hardness tester. As a result, the morphology and composition of anodic film were changed by concentration of sodium silicate. Thickness and Si composition of anodic film was increased with increasing concentration of sodium silicate in electrolyte. The hardness of anodic film was highly increased when the concentration of sodium silicate was above 40 g/l in electrolyte.