• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.335-338
• /
• 2009

The process of charging an oxidizer in the liquid propellant rocket can divide into the cooling of the oxidizer tank, the high flow charge, the small flow charge, and the replenishment charge for the correction of temperature. The oxidizer of the Naro(KSLV-I) first stage uses the liquid oxygen. And the flow rate and the temperature specification corresponding to each charge mode are presented for the requirement. The flow throttling valve and heat exchanger are installed in the oxidizer filling system in order to satisfy this kind of the flow rate and temperature requirement specification. In this research, by using the Flowmaster which is a commercial one-dimension thermo-fluidic analysis program, one dimensional flow system analyses was performed to predict the exact flow rate at each specific mode. Also, the flow rate correction sensitivity of the flow control valves was analytically determined to satisfy the flow condition refinement at each mode within the limited certification test.

• Journal of Navigation and Port Research
• /
• v.35 no.5
• /
• pp.365-370
• /
• 2011

The ice-thermal energy storage cooling system has been applied to relief a significant portion of the peak demand of electricity during the daytime in summer. Slurry ice type system is one kind of ice-thermal storage cooling system utilizing cheaper off-peak electricity. This study is experimented to observe an influence of experimental conditions on production characteristics of slurry ice by using reversing flow, which is putting reversing material into test section to disturb ice adhesion. At this experiment, poly propylene ball of dimeter 10 mm was used as reversing material, and ethylene glycol-water solution of 20wt% concentration was used as flow material. The experimental apparatus was constructed of the slurry ice making and storage tank(test section), the brine tank, pumps for ethylene glycol-water solution and brine circulating, a mass flow-meter, data logger for fluid temperature measuring. The experiments were carried out under various conditions, with volumetric flow rate, ball filling rate and air filling rate.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.2
• /
• pp.144-153
• /
• 2009

It is widely known that no-slip assumptions are often violated on regular basis in micrometer- or nanometer-scale fluid flow. In the case of cavity-filling process of nanoimprint lithography(NIL), slip phenomena take place naturally at the solid-to-liquid boundaries, that is, at the mold-to-polymer or polymer-to-substrate boundaries. If the slip or partial slip phenomena are promoted at the boundaries, the processing time of NIL, especially of thermal-NIL which consumes more tact time than that of UV-NIL, can be significantly improved. In this paper it is aimed to elucidate how the cavity-filling process of NIL can be influenced by the slip phenomena at boundaries and to what degree those phenomena increase the process rate. To do so, computational fluid dynamics(CFD) analysis of cavity filling process has been carried out. Also, the effect of mold pattern shape and initial thickness of polymer resist were considered in the analysis, as well.

• Journal of the Korean Society of Tobacco Science
• /
• v.11 no.1
• /
• pp.71-77
• /
• 1989

The filling effects of test cigarettes prepared the different cutting width on the three brands (NC82, Burley21 and 88Light) were compared with their regular cigarette by the value of "Hardness" and "draw ressistance". Results obtained were as follows: 1. With enlargement of the shred width. The hardness of cigarettes became harder than the standard one in the same filling-weight When the shred width enlarged by 0.2mn from standard, the saving rate of tobacco materials would be 4~5%. 2. As the shred width became wider, Long strand was rich and short strand was poor. 3. The enlargement of the shred width may increase the standard deviation of filling-weight of cigarettes in some case.rettes in some case.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.370-373
• /
• 2009

The runner-valve is an effective solution for the filling balance of the multi cavity molds. Automation of the runner-valve system is necessary for more efficient and accurate control of the filing balance. We designed an automatic runner-valve actuator for the automation and characterized the actuator by experiment. We obtained a linear relationship between motor-driving time and the height of the runner-valve. However, the motor-driving times for upward and downward directions were different due to the frictional characteristics of the actuators. Also we obtained the motor-driving times for backlashes of the 4 actuators. The results were used to formulate the relationship between the resin-arrival time and the flow rate change of the runner-valve with the theoretical equation that was derived in the previous research.

• Journal of Communications and Networks
• /
• v.14 no.2
• /
• pp.151-161
• /
• 2012

This paper considers a two-user Gaussian interference channel with energy harvesting transmitters. Different than conventional battery powered wireless nodes, energy harvesting transmitters have to adapt transmission to availability of energy at a particular instant. In this setting, the optimal power allocation problem to maximize the sum throughput with a given deadline is formulated. The convergence of the proposed iterative coordinate descent method for the problem is proved and the short-term throughput maximizing offline power allocation policy is found. Examples for interference regions with known sum capacities are given with directional water-filling interpretations. Next, stochastic data arrivals are addressed. Finally, online and/or distributed near-optimal policies are proposed. Performance of the proposed algorithms are demonstrated through simulations.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.8 no.3
• /
• pp.124-130
• /
• 2000

This study was conducted to evaluate effects of gas retention time and filling depth of a compost-based biofilter on removal of vapor phase gasoline and to suggest operational improving method. Gas empty bed retention times(EBRTs) were 4, 10, and 20 minutes, respectively. EBRT of over 10 minutes was required in both cases of TPH(total petroleum hydrocarbons) and BTEK (bezene, toluene, ethylbenzene, and xylene). Filling depths were 25, 50, 75, and 100cm, respectively. To treat gasoline TPH effectively, controlling other operational parameters including EBRT and gas loading rate was more important than increasing filling depth simply. 1m filling depth was sufficient in treating BTEX without controlling other operational parameters greatly.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.142-149
• /
• 2003

Blind hydraulic backfilling is a commonly used technique for subsidence control of the strata over unapproachable waterlogged underground excavations. In this investigation model studies on all the three variants of this technique, namely, hydro-pneumatic or air-assisted gravity backfilling, pumped-slurry backfilling and simple gravity backfilling, have been carried out in fully transparent models of the underground excavations. On examination of the filling process, it was revealed that in all the three cases, the basic process of filling occurs by sand transport along one or more meandering channels. The relative influence of sand, water and air flow rates on the area of filling from a single inlet point and the hydraulic pressure loss per unit length were studied in details. In hydro-pneumatic backfilling process, the air bubbles while moving upward through the meandering channels provide an additional buoyant force over and above the available hydraulic head. In this way the area of filling from a single borehole may be quite large even at small flow rates of water. During actual field implementation the injected air, if not released completely from the rise side holes, may cause troubles by way of creating potholes on the surface. The pumped-slurry technique has shown its capability of filling a relatively larger area at faster rate, especially when high-volume, low-pressure method was selected. But simple gravity filling was also found to be equally effective method as slurry pumping, especially when flow rates were high. In the second and third method discussed above, examination of variations of injection pressure was also done and its relation with physical phenomenon was also attempted. Some empirical relationships were also developed using multivariate regression with a view to help the practicing engineers.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.3
• /
• pp.216-222
• /
• 1994

Experiments were conducted in the research field of the former Wheat and Barley Research with three barley cultivars, Olbori, kangbori and Suwon 18, which show different growth characteristics. Relationships between the degree of grain filling and the functions of photosynthetic organs in grain growth post-anthesis were investigated by removal treatment of awns and leaves, Stems and leaf sheath contributed to final grain weight invariably with cultivars by 79.2∼81.4%. while the contribution rate of awns and leaf blades varied by different cultivars, Awns contributed by 11.6∼13.8% in 'Olbori' and 'Kangbori', and 5.4% in 'Suwon 18', Contribution of leaf blades was 15.4% for 'Suwon 18', and 4.8∼8.1% for other cultivars, Of leaf blades upper ones showed a higher contribution rate, Early-maturing cultivars which maintain leaf greenness to the late phase of grain growth or awned cultivars were considered advantageous in grain filling.