• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1697-1702
• /
• 2008

The objective of the review is to introduce the evaluation method of welding joint designs by using forces extracted from FE models. This evaluation method is currently being used for the Southeastern Pennsylvania Transportation Authority (SEPTA) project in the United States by request of the customer Engineer. The evaluation method was applied to critical joints connected by Fillet or Partial Joint Penetration (PJP) welds in car body structure for SEPTA project. The additional manual analysis is required based on the fact that Technical Specification in the United States requires the Contractor to apply Complete Joint Penetration (CJP) welds to all structural connections in Car body. However, in the car body design for Septa project there are some areas where CJP welds are not applied due to structural and manufacturing problems.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.4 s.37
• /
• pp.779-788
• /
• 1998

This paper presents the results of the experimental and analytical investigation for the fatigue strength of welded details frequently used in steel bridges, especially for the details with relatively lower fatigue strength. Considering the measured stress fatigue cracking initiated at toe of the transverse fillet weld joining the gusset plates to the web because of the stress concentration that developed as a result of the geometric conditions and the greater probability of microscopic discontinuities at the fillet weld toe A comparison was made of the stress calculated by considering geometric aspect of bead and measured at same position. They indicate that the geometric conditions of the weld toe result in similar stress concentration on both FEM models and test results. The test results were compared with the fatigue criteria of AASHTO, JSSC specifications. Specimens of 80 and 150mm gusset plate configuration tested either respectively equaled or exceeded the fatigue resistance provided by category D and E of the AASHTO specification. It also satisfied the category F and G of JSSC. Both WG1 and WG3 specimen tend to provide S-N curves with a store near -0.3 less than AASHTO and JSSC.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.56-56
• /
• 2010

최근 강구조물의 건설이 지속적으로 증가되어 왔다. 또한 강구조물의 유지관리 및 안전성에 대한 관심이 급증하고 있다. 시설물의 안전성 확보는 대형사고의 사전 예방, 공용 중 갑작스런 가동 중지에 의하여 발생되는 비용증가를 사전에 차단 할 수 있다는 점에서 그 중요성은 매우 크다고 할 수 있다. 또한 각종 구조물은 열악한 사용조건, 고온, 고압, 고속, 대형화됨에 따라 일단 사고가 발생 했을 경우 대형사고의 위험이 예상되므로, 제작시 검사의 강화뿐만이 아니라 공용 중 구조물의 안전성을 진단 할 수 있는 모니터링 체계의 확립이 필요한 시점이다. 현재 국내에서 강구조물들의 균열 모니터링 시스템에 관한 연구는 매우 미흡한 실정이며, 현재 사용되고 있는 비파괴검사 방법은 UT와 RT등이다. 이러한 방법들은 많은 시간과 경비가 소요되며 또한 거대구조물 혹은 사람의 접근이 어려운 곳에는 적용하기가 힘들다. 또한 주기적인 검사 작업으로 인한 막대한 시간과 비용의 손실이 발생되고 있으며 초기 결함을 조기에 인지하지 못함으로써 적절한 보수 보강 대책이 이루어지지 않아 보수 보강 비용의 증대를 초래한다. 더욱이, 결함이 진전된 이후에도 이것을 인지하지 못하여 적절한 대응을 하지 않는다면 대형사고로 이어질 수도 있다. 따라서 강구조물에 대한 효율적인 유지관리가 가능하고, 초기결함으로부터 균열이 진전하여 붕괴되는 사고를 미연에 방지하며 초기에 보수보강 작업을 수행함으로써 보수보강 비용도 절감 할 수 있는 모니터링 시스템의 개발이 요구되고 있다. 이러한 모니터링 시스템의 개발은 기술적 측면에서 강구조물의 효율적인 유지 관리 노하우를 얻을 수 있으며 경제 산업적 측면에서는 보수 보강 비용 및 불필요한 주기적 점검 비용을 절감 할 수 있다. 이 연구에서는 전위차법을 이용하여 강구조물의 필렛 용접부에서의 균열진전양상을 파악하고 정량화를 통해 필렛용접부의 잔여수명을 예측하였다.

• Journal of Korean Society of Steel Construction
• /
• v.11 no.3 s.40
• /
• pp.319-327
• /
• 1999

This study makes mechanism of the fatigue strength improvement by the processing of weld toe clear for the vertical cross rib specimens which was made fillet weld joint, also it proposes to the appropriate later processing. As a result of tension fatigue test, the fatigue strength improvement could have been seen in later processed specimens than as-weld specimens. Especially fatigue crack initial life $N_c$ increased in specimens which processed grinder after hammer-peening. Also, fatigue crack propagation life $N_p$ improved more in hammer-peening specimens than as-weld or TIG specimens. It thinks that $N_c$ is because of the geometrical shape of weld toe, i.e. the relaxation of the stress concentration and also that $N_p$ is because the big compression residual stress which was introduced in the surface by hammer-peening is restraining the propagation of fatigue crack.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.3
• /
• pp.241-250
• /
• 2003

This study, investigated the characteristics of residual stress in weldis composed of similar or dissimilar steels, are investigated byusing 3three-dimensional thermal elasto-plastic FEM analysis. The results showed that for the groove welding of the similar steels, increasedthetensile strength of the steels (POSTEN60

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.111-122
• /
• 2000

In this study, A series of fatigue tests have been performed on the fillet welded joints of cover plates in steel plate girders in order to quantitatively assess the fatigue characteristics according to the shapes of cover plates. From the results of fatigue tests, it has been shown that the fatigue strengths were slightly different according to their shapes, but satisfied the fatigue design curves in Korea and other countries. Also, from the results of beachmark tests, it has been confirmed that the points of fatigue crack initiation were closely related to the shapes of weld bead toes, and fatigue cracks simultaneously initiated from several points in weld bead toes have been grown as semi-elliptical surface cracks, and these cracks have been coalesced each other, and grown as through thickness cracks, and finally reached to fracture. Besides, from the results of fracture mechanics approaches, stress gradient factors were the most dominant factors among crack correction factors obtained from the existing equations and finite element analysis, and the fatigue life on fillet welded joints of cover plates could be estimated using the relations between fatigue crack growth rate and stress intensity factor range obtained from finite element analysis.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.1
• /
• pp.81-88
• /
• 2017

Residual stress is defined as stress that already exists on a structural member from the effects of welding and plastic deformation before the application of loading. Due to such residual stress, welded H-section compression members under centroidal compression load can undergo buckling and failure for strength values smaller than the predicted buckling load and specified compressive strength. Therefore, this study was carried out to evaluate the effect of residual stress from welding on the determination of the buckling load and specified compressive strength of the H-section compression member according to the column length variation. A three-dimensional nonlinear finite element analysis was performed for the H-section compression member where the welded joint was fillet welded by applying heat inputs of 3.1kJ/mm and 3.6kJ/mm using the SAW welding method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1207-1212
• /
• 2015

A vibro ripper utilizes high-frequency vibration for rock fragmentation. This concept is different from those used by other existing breakers. The gearbox-shank welded joint of a vibro ripper is a very important part. Because it delivers the vibromotive force to the tooth, it is important to predict its soundness. This study was conducted to predict the fatigue life under welding conditions. The shank materials were Hardox-Hituf and AR400, and the filler metals were CSF-71T and CSF-81T. Fatigue tests were conducted under each set of conditions. P-S-N curves are presented based on the statistical testing method recommended by JSME-S002, and a comparison is made of the results under each set of conditions. The life was estimated using a P-S-N curve.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.3
• /
• pp.403-411
• /
• 2002

This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the T-joint has an obvious peak load. with the failure mode of chord-web buckling at a ratio of branch width to chord width ($\beta$) of above 0.8. Similar to a T-joint with chord-flange failure mode, the strength at a certain deformation limit can be regarded as the ultimate strength of a T-joint Based on the experimental results including tests done by Kato and Zhao, the deformation limit was proposed as 3%B for $10.7{\leq}2{\gamma}(B/T){\leq}42.3$ and $0.8{\leq}{\beta}{\leq}1.0$. The strength formula of CIDECT and those of other researchers were also compared with the test results. Finally, the strength formula based on the column buckling was proposed.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.5
• /
• pp.460-470
• /
• 2009

In recent practice a half round prismatic bar has fillet welded or formed through foundry work along the centerline on rear concave surface of the horn to mitigate gap flow between fixed and movable part of the rudder system. When the gap clearance has been blocked with this practice, numerical simulations indicate that the practices are not only effective in reducing the gap flow but also in mitigating the cavitation. The blocking effects are remarkably improved when a pair of blocking bar is bisymmetrically attached with respect to centerline on the opposite convex surface of the movable part. The blocking bar could be placed on the exposed surface under maximum rudder angle. This implies that the blocking bar could be easily adopted not only in a design stage but also in a maintenance stage for mitigating rudder cavitation. In addition, the numerical simulations imply that more improvements could be anticipated through the selection of section shape of prismatic bar for gap flow blocking.