• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1756-1767
• /
• 2008

Recently, a global trend has been established to facilitate the use of waste materials in geotechnical engineering applications. In Korea, where there is the need to save natural resources as these may become scare in the near future and to prevent excessive ground excavation for natural aggregates. The annual production of scrap tire and bottom ash has sharply increased in recent years. Therefore, it will be good waste resource recycling, if we can utilize the above wastes as fill materials in soft ground. In this study, based on the proven feasibility of bottom ash and tire shred-soil mixtures as lightweight fill materials, tire shred-bottom ash mixtures were suggested as a new lightweight fill material to replace the conventional construction material(soil) with bottom ash. Therefore, the main objective of this research is to investigate the feasibility of tire shred-bottom ash mixtures in order to estimate their suitability for the use of lightweight fill materials. So we carried out the performance tests of 2 large scale embankment which were made with tire shred-bottom ash mixture and the conventional fill material(weathered soil) respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.6
• /
• pp.45-52
• /
• 2007

Maintenance of structural and hydrological safety of the superannuated fill dam is very important subject on the viewpoint of disaster prevention. Mainly, the core of the superannuated fill dams have been damaged continuously by the various harmful external forces such as the typhoons, flash floods and earthquake, and these can be connected to the large scaled general dam failure. Therefore, the research on the repair, remediation and reinforcement of dam is necessary. In this study, the permeable grouting method for the remediation of fill dam was examined by the electrical resistivity survey and the change of permeability of core front. As a result, the permeable grouting method can be useful remediation method for the superannuated fill dam, the leakage from the core front decreased greatly before and after the construction of grouting. Furthermore, it can be said that the turbidity of fill dam may not be greatly increased by grouting.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.451-461
• /
• 2016

The objective of this study is to illustrate the methods and procedures for estimating the failure probability of small fill dams subjected to earthquake events and to estimate the seismic failure probability of the Korean disaster risk fill dams where geotechnical information is not available. In this study, first of all, seismic failure probabilities of 7 disaster risk small fill dams, where geotechnical information is available, were evaluated using event tree analysis. Also, the methods and procedures for evaluating probabilities are illustrated. The relationship between dam height and freeboard for 84 disaster risk small dams, for which the safety diagnosis reports are available, was examined. This relationship was associated with the failure computation equation contained in the toolbox of US Army corps of engineers. From this association, the dam height-freeborard critical curve, which represents 'zero' failure probability, was derived. The seismic failure probability of the Korean disaster risk fill dams was estimated using the critical curve and the failure probabilities computed for 7 small dams.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.4
• /
• pp.137-146
• /
• 2017

For the competitive business environment under purchase dependence, this paper proposes a new approximate calculation of order fill rate which is a probability of satisfying a customer order immediately using the existing inventory. Purchase dependence is different to demand dependence. Purchase dependence treats the purchase behavior of customers, while demand dependence considers demand correlation between items, between regions, or over time. Purchase dependence can be observed in such areas as marketing, manufacturing systems, and distribution systems. Traditional computational methods have a difficulty of the curse of dimensionality for the large cases, when deriving the stationary joint distribution which is utilized to calculate the order fill rate. In order to escape the curse of dimensionality and protect the solution from diverging for the large cases, we develop a greedy iterative search algorithm based on the Gauss-Seidel method. We show that the greedy iterative search algorithm is a dependable algorithm to derive the stationary joint distribution of on-hand inventories in the retailer system by conducting a comparison analysis of a greedy iterative search algorithm with the simulation. In addition, we present some managerial insights such as : (1) The upper bound of order fill rate can be calculated by the one-item pure system, while the lower bound can be provided by the pure system that consists of all items; (2) As the degree of purchase dependence declines while other conditions remain same, it is observed that the difference between the lower and upper bounds reduces, the order fill rate increases, and the order fill rate gets closer to the upper bound.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.6
• /
• pp.5-17
• /
• 2012

The moment responses of electric pole foundations for a railway were investigated using real-scale load tests. Large overturning moments were applied to two circular rigid piles with a 0.75 m diameter and a 2.5 m embedded depth; the circular rigid piles were installed in an actual railway embankment fill. Two different loading directions-toward the fill slope and toward the track -were applied to evaluate the influence of the fill slope on the moment capacities of the foundations. It was found that the failure of the foundations that were constructed according to Korean railway practices exhibited a sudden overturning pattern without any significant pre-failure displacement. The moment capacity toward the fill slope was less than the moment capacity toward the track by 30%. From the test results, the geometry factor (K), which accounted for the reduction of the moment capacity, due to the fill slope, was 0.7. Moment capacities determined from the load tests were compared with those predicted from three existing design methods, and their applicability was discussed.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.17-20
• /
• 2006

Passenger safety is fundamental factor in automobile. Among much equipment for passenger safety, the air bag system is the most fundamental and effective device. Beside of the front air bag system which installed on most of all automobiles, a curtain-type air bag is increasingly adapted in deluxe cars fur protecting passengers from the danger of side clash. Curtain type airbag system consists of inflator housing, fill hose, curtain airbag. Inflator housing is a main part of the curtain-type air bag system for supplying high-pressure gases to deploy the air bag-curtain. Fill hose is a passageway to carry the gases from inflator housing to each part of curtain airbag. Therefore, it is very important to design the vent holes of fill hose for good performance of airbag deployment. But, the flow information from vent holes of fill hose is very limited. In this study, we measured instantaneous velocity fields of a high-speed flow ejecting from the vent holes of fill hose using a dynamic PIV system. From the velocity Held data measured at a high frame-rate, we evaluated the variation of the mass flow rate with time. From the instantaneous velocity fields of flow ejecting from the vent holes in the initial stage, we can see a flow pattern of wavy motion and fluctuation. The flow ejecting from the vent holes was found to have very high velocity fluctuations and the maximum velocity was about 480m/s at 4-vent hole region. From the mass flow rate with time, the accumulated flow of 4-vent hole has occupied about 70% of total flow rate.

• Tunnel and Underground Space
• /
• v.24 no.6
• /
• pp.405-417
• /
• 2014

In a high-level waste repository, the gap fill of the engineered barrier is an important component that influences the performance of the buffer and backfill. This paper reviewed the overseas status of R&D on the gap fill used engineered barriers, through which the concept of the gap fill, manufacturing techniques, pellet-molding characteristics, and emplacement techniques were summarized. The concept of a gap fill differs for each country depending on its disposal type and concept. Bentonite has been considered a major material of a gap fill, and clay as an inert filler. Gap fill was used in the form of pellets, granules, or a pellet-granule blend. Pellets are manufactured through one of the following techniques: static compaction, roller compression, or extrusion-cutting. Among these techniques, countries have focused on developing advanced technologies of roller compression and extrusion-cutting techniques for industrial pellet production. The dry density and integrity of the pellet are sensitive to water content, constituent material, manufacturing technique, and pellet size, and are less sensitive to the pressure applied during the manufacturing. For the emplacement of the gap fill, pouring, pouring and tamping, and pouring with vibration techniques were used in the buffer gap of the vertical deposition hole; blowing through the use of shotcrete technology and auger placement and compaction techniques have been used in the gap of horizontal deposition hole and tunnel. However, these emplacement techniques are still technically at the beginning stage, and thus additional research and development are expected to be needed.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.65-70
• /
• 2005

The KOMPSAT program is carrying out successfully in spite of the short domestic space development history, but there are still many difficulties in Koreanization of most core parts. Because the development of core parts is essential to participate in the advanced nations in space based on the mid-long term national space program, KARI has carried out development of Fill/Drain valve for propellant/pressurant supply of satellite, which has high possibilities to be koreanized, with Hanwha Corp.. This paper summarizes overall processes of development including design, manufacturing and test, and finally 4 sets of modules were successfully made. Also the satisfaction of performance requirements are verified through acceptance tests.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.301-310
• /
• 2006

A series of laboratory tests was carried out for analyzing compaction characteristics of hydraulic fill soils(or hydraulically filled soils). Hydraulic fill soils were settled down by the weight of soil particle itself in water and consolidated by the extraction of water from the soil structures. Water content and dry unit weight were observed as the depth of sedimentation and consolidation soil. It was found from the result that the optimum water content $(W_{cpt})$ of the maximum unit weight$(\gamma_{dmax})$ is higher than that of laboratory compaction test(KS F 2312 A method). It was due to difference in compaction energy and compaction effect between two methods. And the maximum dry unit of hydraulic fill soil is smaller than that of laboratory compaction test. Especially in terms of compaction effect, the maximum relative compaction degrees$(R_{cmax})$ of Seamangum dredged sand, river sand and mixed sand, half and half of dredged and river sands, were 85%, 91% and 86%, respectively. It means that the compaction effect can be $85\sim91%$ of the maximum unit weight in laboratory compaction test.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.87-94
• /
• 2008

A method for improving current THD of Valley-fill rectifier is proposed in this paper. The proposed topology combines a boosting inductor with Valley-fill rectifier which carry out AC/DC conversion and PFC simultaneously The boosting effect by PWM switching makes low THD current and improve of Valley-fill rectifier. The operation modes and THD of input current are analyzed as applied the boosting inductor, and the optimum value of boosting inductor is determined A 100[W] single-stage converter has been designed and tested. Experimental results are resented to verify the validity of the proposed method.