• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.264-269
• /
• 2007

Today's research has been focused on changing the light source from filament to LED for luminarie illumination to overcome the shortcoming of a filament. The purpose of this research is to make an appropriate high power LED package structure for luminarie. We simulated radiation patterns of the various structures by the ray tracing simulator (Light Tools), and also analyzed the radiation patterns using an LED test system (OL770). As we increased an inner reflector angle, the radiation pattern split into two peaks and the angle between two peaks became larger. In addition, when we increased an outer reflector angle, the angle between side peaks gradually decreased, while it increased again when the angle reach $50^{\circ}$. These results could be understood from the ray tracing of the light reflected from two reflectors. We made the high power LED package for luminarie on the condition of the optimized structure which was made by ray tracing simulation results, and we measured the radiation patterns by using an LED test system, and these results were well matched to the simulation results.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.20 no.2
• /
• pp.61-67
• /
• 2010

The bivoltine tropical tasar ecoraces of Antheraea mylitta Drury produces cocoons for seed production under seed crop rearing (July-August with $22{\sim}30^{\circ}C$ temperature and 50~70% relative humidity) and for silk production under commercial crop rearing (September-December with $17{\sim}27^{\circ}C$ temperature and 60~80% relative humidity). To consider the impact of hybrid vigour on egg, larva, cocoon and silk related commercial traits, the $F_1$ hybrids made among Daba, Jata and Raily ecoraces were assessed successively for three years. The hybrid vigour in the $F_1$ hybrid of Daba$\times$Jata ($T_7$) was positive for egg fertility (+23.1%), shell weight (+25.6%), silk yield (+79.0%) and filament length (+68.1%), with filament of high denier (11.98d) and reduced larval span (-7.1%). The Jata$\times$Daba ($T_8$) hybrid has shown negative heterosis in egg fertility (-8.0%) compared to the other F1 hybrids, Daba$\times$Raily ($T_9$) and Raily$\times$Daba ($T_{10}$), when they rise simultaneously during the commercial crop season. The better performance of parental ecoraces ($T_4$ to $T_6$) in their commercial traits during commercial crop over parents of seed crop ($T_1$ to $T_3$) and the superior performance of $F_1$ hybrids ($T_7$ to $T_{10}$) over parents of commercial crop ($T_4$ to $T_6$) during commercial crop season indicates the apparent hybrid vigour in tasar $F_1$ hybrids. As the Daba$\times$Jata ($T_7$) and Jata$\times$Daba ($T_8$) $F_1$ hybrids have shown highest hybrid vigour, their rearing during commercial crop can optimize the silk productivity and commercial sustenance of the tasar silk industry.

• Fashion & Textile Research Journal
• /
• v.14 no.4
• /
• pp.641-647
• /
• 2012

This study investigates the sound properties of fabric frictional sound (SPL, ${\Delta}L$, ${\Delta}f$) according to the film type of PTFE laminated vapor-permeable water-repellent fabrics in order to understand the relationship between SPL and the basic properties of fabrics such as layer, yarn type, and thickness of fiber. This study accesses their mechanical properties and determines how to control them to minimize SPL. Eight PTFE laminated water-repellent fabrics, composed of four different film types (A, B, C, D) and with two different fabrics, were used as test specimens. Frictional sounds generated at 1.21m/s were recorded by using a fabric sound generator and SPLs were analyzed through Fast Fourier Transformation (FFT). The mechanical properties of fabrics were measured by KES-FB. The SPL value was lowest at 74.4dB in film type A and highest as 85.5dB in type D. Based on ANOVA and post-hoc test, specimens were classified into less Loud Group (A, B) and Loud Group (C, D). It was shown that SPL was lower when 2 layer (instead of 3 layer), filament yarn than staple, and thin fiber than thick were used. In Group I, shearing properties (G, 2HG5), geometrical roughness (SMD), compressional properties (LC, RC) and weight (W) showed high correlation with SPL however, elongation (EM) and shear stiffness (G) did with SPL in Group II.

• Fashion & Textile Research Journal
• /
• v.15 no.6
• /
• pp.985-992
• /
• 2013

Polytrimethylene terephthalate(PTT) offers several advantageous properties such as good tensile strength, uniformity, stiffness, toughness, UV stability, resilience, stain resistance, outstanding elastic recovery, and dyeability. The effects of annealing temperature on physical properties and the structure of PTT filaments and yarn were investigated by measuring wide-angle X-ray diffraction (WAXD), density, optical birefringence, dynamic visco elasticity, and tensile testing. The intensity of maximum tan ${\delta}$ decreased and the temperature of maximum tan ${\delta}$ shifted to a higher temperature as the annealing temperature of filaments increased; however, it shifted to a lower temperature when the annealing temperature exceeded $130^{\circ}C$. In addition, crystallinity, density and D-spacing of (010) crystal face increased as the annealing temperature increased. Optical birefringence and specific stress were almost constant up to $100^{\circ}C$ and then decreased above $130^{\circ}C$. The shrinkage of PTT filament is 0 in boiling water when annealed above $130^{\circ}C$; consequently, the use of annealed fiber above $130^{\circ}C$ can remove thermal instability when dyeing PTT fiber. In the case of yarns, the thermal stability and physical properties of yarns showed the best effect when the ply number is less than 5, twist number is less than 400tpm, and the annealing time is 20minutes.

• Textile Coloration and Finishing
• /
• v.26 no.1
• /
• pp.22-31
• /
• 2014

This study investigated the physical properties of warm up yarns and their knitted fabrics including the dye affinity and color fastness to washing of these knitted fabrics according to the various dyeing times and temperatures on dyeing process. The results were summarized as follows. The tenacity of Nylon/PP warm-up yarn was 4g/d and breaking strain was 4.5%. The wet and dry thermal shrinkages were higher than those of PET warm-up yarn. The maximum heat flow rate(Qmax) of Nylon/PP warm-up knitted fabric was lower than that of PET warm-up knitted fabric and heat keeping rate(a) of Nylon/PP warm-up knitted fabric was higher as 47% than that of PET warm-up knitted fabric. It was shown that the shape retention and wearing comfort of Nylon/PP warm-up knitted fabric were better than those of PET warm-up knitted fabric. The dye-affinity(K/S) of Nylon/PP warm-up knitted fabric showed maximum value at the dyeing condition of 40minute or 50minute dyeing time with $80^{\circ}C$ dyeing temperature, but PET warm-up knitted fabric showed maximum value at the 30minute or 40minute with $110^{\circ}C$ dyeing temperature. Finally, the color fastness to washing of Nylon/PP warm-up knitted fabric showed good value as between 4 and 5 grade.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.5
• /
• pp.294-302
• /
• 2021

In this study, the 3D printing technique called design for additive manufacturing (DfAM) that is widely used in various industries was applied to marine leisure ships of equipment. The DfAM for the stanchion for crew safety was applied to the equipment used in an actual recreational craft. As design constraints, the design alternatives were not to exceed the safety and weight of the existing stainless steel material, which were reviewed, and the production of a low-cost FFF-type 3D printing method that can be used even in small shipyards was considered. Until now, additive manufacturing has been used for manufacturing only prototypes owing to its limitations of high manufacturing cost and low strength; however, in this study, it was applied to the mass production process to replace existing products. Thus, a design was developed with low manufacturing cost, adequate performance maintenance, and increased design freedom, and the optimal design was derived via structural analysis comparisons for each design alternative. In addition, a life-cycle assessment based on the ISO 1404X was conducted to develop sustainable products. Through this study, the effectiveness of additive manufacturing was examined for future applications in the shipbuilding industry.

• Journal of the Korea Convergence Society
• /
• v.12 no.3
• /
• pp.141-149
• /
• 2021

3D printers, which emerged in the late 20th century, have become a key part of the fourth industrial revolution in the 21st century. Although 3D printers, the key equipment of the maker movement and the starting point of the new cottage industry in the 21st century, still reveal the limitations of mass production with low output speed and limited filament materials, the use of 3D printers by ceramic craftsmen has recently increased exponentially. However, as part of a way to overcome the discord between craftsmanship and the new technology, which has been repeated over and over in the past in craft history, the study focused on the 'plaster mold casting' technique using 3D printers. Therefore, after analyzing casting techniques of Tony Hansen, Webe van Gansbeck, Jade Crompton, and Ryu Hee-do, the potters who actively developed gypsum techniques in the world's ceramic crafts field and applied them to their own designs, I tried to find the point of convergence between 3D printers and ceramic crafts by presenting examples of effective 3D modeling methods and optimal slip casting methods using 3D printers.

• Fashion & Textile Research Journal
• /
• v.22 no.6
• /
• pp.834-843
• /
• 2020

This study develops 1/2 dress forms for draping. This study investigated the production status of domestic and foreign products in order to model their shape using CLO 3D. In addition, it developed torso-type and torso-crotch-type products that allowed for draping using a 3D printer. This study analyzed shape and size compared to developed ones after referring to the Size Korea 7th Survey data as well as seven domestic and foreign company websites. The results are follows. First, an investigation of the production status of the products for the size of most of the domestic ones (except K-4) indicated that the waist circumference was slimmer than Size Korea. Bust, waist, and hip circumferences ranged from 42.0 cm, 32.0 cm, and 45.0 cm - 49.0 cm, respectively, in Chinese products; 42.0 cm - 43.0 cm, 30.5 cm - 31.5 cm, and 46.0 cm - 46.5 cm in Japanese products; 43.0 cm, 35.0cm, and 46.5 cm in American products (Japanese body shape applied). Second, an avatar was produced on a 3D software with the average size of 20-24year-old women, and its file modified as a dress form for 3D printing with PLA filament to produce dress forms for draping, workable with pins, using quilting cotton and cotton cloth. Third, the comparisons of the form and flattening between the developed dress forms and the selling ones indicated that flattening was bigger in the waist part of the former than the latter. The waist is produced too slim in the existing dress forms; therefore, it is necessary to correct the waist circumference. Unlike existing dress forms, the developed ones were produced in proximity to the average size of 20-24 year-old women in the Size Korea 7th Survey.

• Advances in nano research
• /
• v.14 no.5
• /
• pp.435-442
• /
• 2023

Sports activities, including playing tennis, are popular with many people. As this industry has become more professionalized, investors and those involved in sports are sure to pay attention to any tool that improves athletes' performance Tennis requires perfect coordination between hands, eyes, and the whole body. Consequently, to perform long-term sports, athletes must have enough muscle strength, flexibility, and endurance. Tennis rackets with new frames were manufactured because tennis players' performance depends on their rackets. These rackets are distinguished by their lighter weight. Composite rackets are available in many types, most of which are made from the latest composite materials. During physical exercise with a tennis racket, nanocomposite materials have a significant effect on reducing injuries. Materials as strong as graphite and thermoplastic can be used to produce these composites that include both fiber and filament. Polyamide is a thermoplastic typically used in composites as a matrix. In today's manufacturing process, materials are made more flexible, structurally more vital, and lighter. This paper discusses the production, testing, and structural analysis of a new polyamide/Multi-walled carbon nanotube nanocomposite. This polyamide can be a suitable substitute for other composite materials in the tennis racket frame. By compression polymerization, polyamide was synthesized. The functionalization of Multi-walled carbon nanotube (MWCNT) was achieved using sulfuric acid and nitric acid, followed by ultrasonic preparation of nanocomposite materials with weight percentages of 5, 10, and 15. Fourier transform infrared (FTIR) and Nuclear magnetic resonance (NMR) confirmed a synthesized nanocomposite structure. Nanocomposites were tested for thermal resistance using the simultaneous thermal analysis (DTA-TG) method. scanning electron microscopy (SEM) analysis was used to determine pores' size, structure, and surface area. An X-ray diffraction analysis (XRD) analysis was used to determine their amorphous nature.

• Science of Emotion and Sensibility
• /
• v.18 no.1
• /
• pp.49-58
• /
• 2015

This paper investigated far-infrared emission characteristics of ZrC imbedded heat storage knitted fabrics for emotional garment. For this purpose, ZrC imbedded heat storage PET was spun with high viscosity PET imbedded ZrC powder on the core part and low viscosity PET on the sheath part by conjugated spinning method. Ingredient analysis and far-infrared emission characteristics assessment of spun filament were carried out by EDS and FT-IR spectrometer. Two kinds of knitted fabrics were made using texturized ZrC imbedded PET for measuring thermal characteristics of ZrC imbedded heat storage PET. Zr peak was certified by EDS measurement and it was confirmed that content of Zr was 19.29%. Far-infrared analysis revealed that emission power at the range of wavelength, $5{\sim}20{\mu}m$ was $3.65{\times}10^2W/m^2$, and emissivity was 0.906. Heat storage analysis by KES-F7 system revealed that $Q_{max}$ of ZrC imbedded PET knitted fabric was lower than that of regular PET one and warmth keepability rate was higher than that of regular one, which means that ZrC imbedded PET knitted fabric has heat storage property. Thermal conductivity of ZrC imbedded PET knitted fabric was higher than that of regular PET one which was caused by high thermal conductivity of Zr itself. Hand property of ZrC imbedded knitted fabric was not inferior compared to regular PET knitted fabric, which preferably was found to be dependent on knit structure and surface property.