• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.358-364
• /
• 2009

This paper is to investigate the influence of driving patterns of slow and high speed vehicles on the performance of continuously regenerating diesel particulate filter(DPF) system matched with operating conditions in field application. The DPF performance test for field application was carried out for two identical DPFs installed to slow and high speed vehicles. A slow speed vehicle was selected among local buses which have driving patterns to repeat running and stop frequently, while a high speed vehicle was prepared to have long route of high speed over 60km/h like inter-city buses. In this test, the regeneration performance on the DPF of slow speed vehicle deteriorated because of high soot load index(SLI) in spite of same balance point temperature(BPT) distribution for high speed vehicle. The DPF of slow speed vehicle melted in the end because the rapid increase of back pressure caused high temperature over $1200^{\circ}C$ in the ceramic wall of DPF. The PM components like ash collected to the filter in the DPF were analyzed in order to investigate the cause of the defect and provide an operation performance of DPF system. In the result of the analysis, high levels of lubrication oil ash(Ca, Mg, P, Zn) were detected.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.9
• /
• pp.2481-2493
• /
• 1996

A simple iterative design method is presented for the miniaturized dielectric filter with finite transimmission zeros. Circuit-network transformations are used to place transission zeros in the stop band. This method is simple and quick compared with conventional pole-synthesis methods. the design of the coupling EM patternof the filter needs the much computation time because its design is carried out through the field simulatior. In this paper, an efficient implementation technique of coupling circuit parameters is presented. This technique uses a linear mapping function between the circuit parameter domain and EM parameter domain to save the high computational time of EM simulator. A narrow band asymmetric filter with a transmission zero is designed and fiblicated through these technique in 1900 MHz band.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.3985-3995
• /
• 2022

The emergence of new nanoscale technologies has imposed significant challenges to designing reliable electronic systems in radiation environments. A few types of radiation like Total Ionizing Dose (TID) can cause permanent damages on such nanoscale electronic devices, and current state-of-the-art technologies to tackle TID make use of expensive radiation-hardened devices. This paper focuses on a novel and different approach: using machine learning algorithms on consumer electronic level Field Programmable Gate Arrays (FPGAs) to tackle TID effects and monitor them to replace before they stop working. This condition has a research challenge to anticipate when the board results in a total failure due to TID effects. We observed internal measurements of FPGA boards under gamma radiation and used three different anomaly detection machine learning (ML) algorithms to detect anomalies in the sensor measurements in a gamma-radiated environment. The statistical results show a highly significant relationship between the gamma radiation exposure levels and the board measurements. Moreover, our anomaly detection results have shown that a One-Class SVM with Radial Basis Function Kernel has an average recall score of 0.95. Also, all anomalies can be detected before the boards are entirely inoperative, i.e. voltages drop to zero and confirmed with a sanity check.

• Journal of Fisheries and Marine Sciences Education
• /
• v.21 no.1
• /
• pp.68-77
• /
• 2009

In this study it will be discussed how to solve the problem of discomfort from rolling motion on the small fishing boats. Up to now, the equipments of reducing rolling system can be examined by various case, but difficult to apply small vessel by function, space and costly establishment. A way of improving the feeling of getting on a boat through the equipped sail at stern edge of bulwark top was researched and developed. The author has tested the sailing performance of the experimental skiff boat, from the signals obtained by the inclinometer in irregular waves and compared with the results got in sail on and off mode operation for 10 minutes duration at the conditions of stop and underway. These data has been analyzed in the application statistical methods. Eventually we summarize the analyzed results obtained from the vessel while stationary and underway for two cases, the vessel with a sail and the vessel without a sail. The field test was done in Jeju outer harbor. The ratio of the motion responses at resonance for the sail with and without cases indicate that under given conditions the motion was reduced by the efficiency of diminution is 4.726%, 2.792% in the stopping and 11.663%, 3.282% in the underway and mean rolling periods are 2.158, 2.142, 2.421, 2.412sec. and 1.968, 1.963, 2.089, 2.051sec. respectively. Consequently the efficiency of diminution was higher when the ship is underway and rolling periods got longer in the equipped sail.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.197-202
• /
• 2002

In this paper, we want to help understanding about telecentric as introducing the concept of the system and researching the optical properties after we choose the designed profile projection lens. An analyzed optical system is F-number=2.8 and the first lens is used negative lens. Accordingly, we can know this system is compacter, because the front focal position is to the inside of the system and aperture stop is designed to the inside of the optical system. The field is about $21^{\circ}$. Since the entrance pupil is located the front focal point, we can certify the exit pupil is -49404.1mm, located on the infinite toward the object space. Therefore, the optical system is the form of 'image space telecentricity'.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.1
• /
• pp.33-40
• /
• 2004

The divide-and-conquer method is efficiently used in parallel multiplier over finite field $GF(2^n)$. Leone Proposed optimal stop condition for iteration of Karatsuba-Ofman algerian(KOA). Ernst et al. suggested Multi-Segment Karatsuba(MSK) method. In this paper, we analyze the complexity of a parallel MSK multiplier based on the method. We propose a new parallel MSK multiplier whose space complexity is same to each other. Additionally, we propose optimal stop condition for iteration of the new MSK method. In some finite fields, our proposed multiplier is more efficient than the KOA.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.43 no.6 s.312
• /
• pp.17-25
• /
• 2006

As information systems to be computerized get significantly scaled up, data modeling issues apparently considered to be crucial once again as the early 1980's under the terms of data governance, data architecture or data quality. Unfortuately, merely resorting to heuristics-based field approaches with more or less no firm theoretical foundation of knowledge with regard to criteria of data design lead quite often to major failures in efficacy of data modeling. In this paper, we have compared normalization-critical data modeling approach, well-known as the Non-Stop Data Modeling methodology in the literature, to the Information Engineering in which in many occasions the notion of do-normalization is supported and even recommended as a mandatory part in its modeling nature. Quantitative analyses have revealed that NS methodology ostensibly outperforms IE methodology in terms of efficiency indices like adequacy of entity judgement, degree of existence of data circulation path that confirms the balancedness of data design and ratio of unnecessary data attribute replication.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.43-46
• /
• 2018

This paper has designed a wideband bandpass filter (WBSF : Wide Band Stop Filter) using a stepped impedance resonator (SIR : Stepped Impedance Resonator) with improved performance and improved hairpin coupling structure. The SIR WBSF is small in size and has the advantage of having excellent bandstop characteristics. The designed BSF has a structure in which a quadrangular shaped hairpin of a / 4 length is arranged symmetrically on the upper and lower sides of the input and output transmission lines. The input and output terminals were terminated at 50 ohms for system applications. The center frequency of the SIR WBSF is 6.3 GHz, which is the second harmonic of 3.15 GHz. The designed filter has a 3dB bandwidth of 2.9 GHz and a transmission coefficient ($S_{21}$) of 33.2 dB. The reflection coefficient ($S_{11}$) at the center frequency is 0.106 dB. The application field is used for fixed microwave relay stations, fixed satellite and earth stations, and fixed satellite communications. The overall size is $20mm{\times}10mm$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.99-104
• /
• 2006

In this paper, the conventional 2 dimensional metamaterial structure has degeneration of shielding characteristic in cross polarization effect. The proposed 3-D resonator is designed for reduction of cross polarization effect. The proposed 3-D resonator using LTCC consists of 2-D parallel resonators on X-axis, Y-axis and Z-axis. The 2-D parallel resonator consists of two plate and one via. When the co-polarization electric filed is excited, the resonance frequency of 3-D resonator is 5.024GHz. The stop bandwidth is 19MHz. When the cross-polarization electric field is excited, the resonance frequency of 3-D resonator is 4.825GHz. The stop bandwidth is 19MHz. The proposed 3-D resonator achieve reduction of cross-polarization effect. The concrete consists of proposed 3-D resonator and absorbtion materials. The concrete will be applied for reduction or interference signal of ETCS(Electric Toll collection system).

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.79-79
• /
• 1999

The varous techniques for fabrication of si or metal tip as a field emission electron source have been reported due to great potential capabilities of flat panel display application. In this report, 240nm thermal oxide was initially grown at the p-type (100) (5-25 ohm-cm) 4 inch Si wafer and 310nm Si3N4 thin layer was deposited using low pressure chemical vapor deposition technique(LPCVD). The 2 micron size dot array was photolithographically patterned. The KOH anisotropic etching of the silicon substrate was utilized to provide V-groove formation. After formation of the V-groove shape, dry oxidation at 100$0^{\circ}C$ for 600 minutes was followed. In this procedure, the orientation dependent oxide growth was performed to have a etch-mask for dry etching. The thicknesses of the grown oxides on the (111) surface and on the (100) etch stop surface were found to be ~330nm and ~90nm, respectively. The reactive ion etching by 100 watt, 9 mtorr, 40 sccm Cl2 feed gas using inductively coupled plasma (ICP) system was performed in order to etch ~90nm SiO layer on the bottom of the etch stop and to etch the Si layer on the bottom. The 300 watt RF power was connected to the substrate in order to supply ~(-500)eV. The negative ion energy would enhance the directional anisotropic etching of the Cl2 RIE. After etching, remaining thickness of the oxide on the (111) was measured to be ~130nm by scanning electron microscopy.