• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.8-14
• /
• 2011

The optimal geometry of the gate field plate in AlGaN/GaN-on-Si HEMT has been proposed using two-dimensional device simulation to achieve a high breakdown voltage for a given gate-to-drain distance. It was found that the breakdown voltage was drastically enhanced due to the reduced electric field at the gate corner when a gate field plate was employed. The electric field distribution at the gate corner and the field plate edge was investigated as functions of field plate length and insulator thickness. According to the simulation results, the electric field at the gate corner can be successfully reduced even with the field plate length of 1 ${\mu}m$. On the other hand, when the field plate length is too long, the distance between field plate and drain electrode is reduced below a critical level, which eventually lowers the breakdown voltage. The highest breakdown voltage was achieved with the field plate length of 1 ${\mu}m$. According to the simulation results varying the $SiN_x$ film thickness for the fixed field plate length of 1 ${\mu}m$, the optimum thickness range of the $SiN_x$ film was 200 - 300 nm where the electric field strength at the field plate edge counterbalances that of the gate corner.

• Journal of Astronomy and Space Sciences
• /
• v.37 no.2
• /
• pp.77-84
• /
• 2020

We performed high-resolution three-dimensional global magnetohydrodynamic (MHD) simulations to study the interaction between the Earth's magnetosphere and a prolonged steady southward interplanetary magnetic field (IMF) (Bz = -2nT) and slow solar wind. The simulation results show that dayside magnetic reconnection continuously occurs at the subsolar region where the magnetosheath magnetic field is antiparallel to the geomagnetic field. The plasmoid developed on closed plasma sheet field lines. We found that the vortex was generated at the magnetic equator such as (X, Y) = (7.6, 8.9) R_E due to the viscous-like interaction, which was strengthened by dayside reconnection. The magnetic field and plasma properties clearly showed quasiperiodic variations with a period of 8-10 min across the vortex. Additionally, double twin parallel vorticity in the polar region was clearly seen. The peak value of the cross-polar cap potential fluctuated between 17 and 20 kV during the tail reconnection.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.172-176
• /
• 1997

It is likely that the corona discharge appears due to the motion and the multiplication of electron and ion under the nonuniform electric field. Because the motion and the multiplication of electron and ion are the function of electric field, for the simulation of the corona discharge, we have to calculate the electric field, before the calculation of the motion and the multiplication of electron and ion. In this paper, the electric field is calculated on the assumption that the gap between a hyperboloidal needle and a plane is 1-dimension, and the motion and the multiplication of electron and ion are determined by Flux-Corrected Transport method. For this purpose, we solve the electron and ion continuity equation together with Poisson equation. We calculated the current density and the electron and ion density distributions between electrodes as well as electric field distortion due to the space charge assuming that the discharge channel radius is 100${\mu}{\textrm}{m}$. In this simulation, it is found that the current density has one peak as observed by experiment, and electric field distortion is important to the formation and the stability of the corona discharge.

• Korean Journal of Agricultural Science
• /
• v.45 no.1
• /
• pp.120-127
• /
• 2018

The rural labor force has gradually been decreasing due to the decrement of the farm population and the increment of the aging population. To solve these problems, it is necessary to develop and study autonomous agricultural machinery. Therefore, analyzing the dynamic behavior of vehicles in an autonomous agricultural environment is important. Until now, most studies on agricultural machinery, especially on ground vehicle dynamics, have been done by field tests. However, these field test methods are time consuming and costly with seasonal restrictions. A research method that can replace existing field test methods by using simulations is needed. In this study, we did basic research analyzing the effect of the travelling speed of a tractor on tire slip using simulation software. A tractor simulation model was developed based on field conditions following a straight path. The simulation was done for three ranges of speed: 20 - 30 km/h (considered the normal travelling speed range), 6 - 8 km/h (considered the plow tillage speed range) and 2 - 4 km/h (considered the rotary tillage speed range). The results of the simulation show that the slip ratio and slip angle values tended to increase as the traveling speed range of the tractor decreased. From the simulation results, it can be concluded that at low tractor speeds, it becomes more difficult to control the vehicle path. In future research, simulations will be done with various work environments such as a curved path as well as with various friction coefficient conditions, and the simulation results will be experimentally verified by applying them to an agricultural tractor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.10
• /
• pp.907-913
• /
• 2015

This work presents a method to predict the near magnetic field distribution on the digital switching circuit mounted on PCB using co-simulation of circuit and electromagnetic fields. The proposed method first obtains the normalized near field distribution by exciting the signal and power ports of the switching circuit using sinusoidal sources. Then the real near magnetic field distribution is determined by weighting the normalized field distribution using the current spectrum of the switching circuit. To confirm the proposed method, a switching IC with a ring oscillator and a output buffer is fabricated and measured in the form of chip-on-board. The surface magnetic field distribution is measured using a magnetic probe above the PCB and compared with the simulation results. Experimental results show the correspondence between simulation and measurement results within 10 dB up to fifth harmonics.

• Journal of the Korea Society for Simulation
• /
• v.25 no.2
• /
• pp.1-11
• /
• 2016

The floor field model (hereafter referred to as FFM) is a cellular automata (hereafter referred to as CA)-based walk model used to model pedestrian behavior. Existing studies on FFM conducted experiments with simple structures (that have one room or one obstacle in a room) or relatively complicated structures (that have many rooms). In order to apply the FFM to real buildings, it is necessary to have additional methodologies to process information about the number of rooms, floors, stairs, and exit doors. In particular, it is necessary to process exit doors during this procedure. Exit doors that are recognized by pedestrians are of many types such as exit doors in rooms, stairs connected to corridors, and exit doors in a building. When calculating the static floor field (hereafter referred to as SFF) in the FFM, information about exit doors is needed and simulation results will be different depending on how the SFF is calculated using an exit door among the above-mentioned exit doors. In this study, an XML-format building data model is proposed according to data structures required by the FFM. This study also defines a methodology to process a number of exit doors. Accordingly, this study developed a building data construction and evacuation simulator and simulation experiments were conducted with university campus building.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.445-450
• /
• 2001

The objective of this study is to develop the GLEAMS-PADDY model for nutrients loading simulation from paddy-field areas. This model is developed by modifying the GLEAMS model. The model is composed of hydrology, sediment and chemical parts. The model was evaluatd using field data. The model estimates water balance and nutrients concentrations reasonably well. The model can be applied to find BMP's in the paddy areas.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1987-1989
• /
• 2000

In this paper, electric field distribution of dielectric sphere considering surface or volume resistivity is analysed by the use of rotational symmetric charge simulation method. We applied three methods such as ${\alpha},{\beta}$ modified $\beta$ method to check electric field calculation error. We find f method and modified $\beta$ method are suitable to simulate volume and surface resistivity respectively.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.297-300
• /
• 2008

High-resolution mesoscale meteorological modeling requires more accurate and higher resolution digital elevation model (DEM) data. Shuttle Radar Topographic Mission (SRTM) has created 90 m DEM for entire globe and that is freely available for meteorological modeling and environmental applications. In this research, the effects of the topographic interpolation methods on high-resolution wind field simulation in the coastal regions were quantitatively analyzed using Weather Research and Forecasting (WRF) model with SRTM data. Sensitivity experiments with three different interpolation schemes (four-point bilinear, sixteen-point overlapping parabolic and nearest neighbor interpolation methods) were preformed using SRTM. In WRF modeling with sixteen-point overlapping parabolic interpolation, the coastal line and some small islands show more clearly than other cases. The maximum height of inland is around 140 meters higher, while the minimum of sea height is about 80 meter lower. As it concerns the results of each scheme it seems that the sixteen-point overlapping parabolic scheme indicates the well agreement with observed surface wind data. Consequently, topographic changes due to interpolation methods can lead to the significant influence on mesoscale wind field simulation of WRF modeling.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.1947-1955
• /
• 1989

With the increasing complexity of cabling at sensory level in process control and manufacturing automation, field buses were introduced to replace the traditional point to point links from each sensor or acruator to its controlling equipments by a single link on which all information is transmitted seriall and multiplexed in time. In this papr, we introduce the BITBUS network as a field bus. For the service discipline of the BITBUS network, two service strategies are proposed to obtain the performance of the network. They are the equal priority cyclic service strategy and the non-equal priority cyclic service strategy. The former assigns equal priority to each node for polling and the latter assumes non-equal priority. The BITBUS network was modeled as a cyclic queueing model and it is analyzed by two methods: the Kuehn's and the Boxma's. Computer simulation was also done for the cyclic queueing model and simulation results were compared with those. Under mathematically non-analyzable environment, only the computer simulation was done. From the simulation result, in order to meet the response time requirement of 5 msec imposed by International Electrotechnical Commission when each node has the average traffic of 5000 messages/sec in manufacturing automation the number of slave nodes should be smaller than 10 at the transmission rate of 2.5 Mbps.