• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.5
• /
• pp.142-148
• /
• 2004

In this paper, to detect exciting frequency on the latticed fence structure, fiber optic sensor using Sagnac interferometer was fabricated and tested. The latticed structure fabricated with dimension of 180 cm wide and 180 cm high, the optical fiber, 50 m in length, distributed and fixed on the latticed structure. Single mode fiber, a laser with 1,550 m wavelength, and $3{\times}3$ coupler were used. Excited vibration signal applied to the latticed structure from 200 Hz to 1 KHz. The detected optical signals were compared to the detected acceleration signals and analyzed on the time and frequency domain. Based on the experimental results, fiber optic sensor using Sagnac interferometer detected exciting frequency, effectively. This system can be applied to the structural health monitoring system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.10
• /
• pp.49-57
• /
• 2010

In order to provide electricity to users economically and safely, distribution automation systems (DASs) monitor and operate components of distribution systems remotely through communication networks. The fiber optic communication network has been mainly installed for the DAS of Korea Electric Power Corporation (KEPCO) because of its huge bandwidth and dielectric noise immunity. However, the fiber optic communication network has some shortcomings that its installation cost and communication fee are expensive. This paper proposes a complex network where WLANs are combined with conventional fiber optic communication networks in order to expand DAS easily and inexpensively. A fixed wireless bridge communication unit (FWB-CU) for the proposed complex network is implemented using IEEE 802.11a WLAN technology. The proposed complex network is built actually to verify its feasibility experimentally as a DAS communication network.

• Journal of Sensor Science and Technology
• /
• v.17 no.2
• /
• pp.95-99
• /
• 2008

Various etching methods of optical fiber and formation of metal nano particles on the optical fiber have been proposed for fabrication of fiber optic localized surface plasmon resonance (FO LSPR) biosensors. Different types of etched optical fiber are possible by removing the cladding of optical fiber using HF (hydrofluoric acid) solution and BHF (buffered hydrofluoric acid) solution, which results in improved surface roughness when BHF solution is used. Localized surface plasmon can be formed and measured by formation of silver and gold nano particles on the etched optical fiber. The characteristics of the etched optical fiber and metal nano particles on the etched surface of the optical fiber play a key role in dictating the sensitivity of the LSPR sensors, so that the proposed results can be expected to be applied for related research on fiber optic based biosensors.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1887-1889
• /
• 1997

This paper reports the principle, design, configuration, and test results of the fiber optic security system using multimode fiber. In this system, optical fiber works as a sensing element. The length of sensing element may be from several meters to several killometers. Physical principle of this system is the dependence of interferometric pattern on the end of the fiber on mechanical perturbation in the area, where this fiber is situated. Near and far field patterns of the output light for multimode fiber are speckle pattern. A number of speckles on the fiber depends on mode numbers. Light intensity in each point of the fiber end depends on phase difference of modes. Finally we introduced a "Fiber Optic Security System based on Multimode" Fiber which we developed, it may be available in the field of the important area and building.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.508-510
• /
• 1995

A fiber-optic pressure sensor is fabricated with a photoelastic glass material. To remove the influence of external pertubation along the optical fiber, a new referencing technique is proposed by using two light sources. LED with 870nm wavelength is used as light source for reference signal, and LED with 660nm wavelength is used as light source for modulation signal. The fiber-optic pressure sensor system shows good linearity within the pressure range of 0 to 5 $kg/cm^2$.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1152-1156
• /
• 1999

In this study, a fiber optic air-backed mandrel hydrophone has been constructed and performance of acoustic signal detection has been measured. The hydrophone is based on a Mach-Zehnder interferometer with 35 m of sensing fiber. The sensitivity is measured up to -128 dB re rad/$\mu$ Pa in range from 1.4 kHz to5 kHz. A system with this design of hydrophone may be applied to detect low frequency underwater acoustic signals.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.2
• /
• pp.157-163
• /
• 2007

Crack detection technique for concrete structures has been developed in this study. Experimental tests were carried out to detect a surface and internal crack, employing common fiber optic cables and OTDR(optical time domain reflectometry), an optical signal analyzer which is widely used to detect damages at fiber optic cables in the field of optical engineering. While initial concrete crack is ready to occur under cracking force, the occurrence and location of the crack are simultaneously detected to give the same damage to fiber optic cables which have been attached to and/or embedded into concrete in advance. It is obtained through successive tests that the principal factors for crack detection is the covering state of fiber optic cable, and total 4 tests including a preliminary test were conducted and the crack detection technique was verified. The practical usefulness would be expected at crack management and maintenance of concrete structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.157-163
• /
• 2008

This paper presents a novel fiber optic tiltmeter system for the health monitoring of large-size structures. The system is composed of a sensor head, a light control unit and a signal processing unit. The sensing mechanism of the sensor head is based on a novel integration of the moire fringe phenomenon with fiber optics to achieve a robust performance in addition to its immunity to EM interference, easy ratting, and low cost. In this paper, a prototype of the fiber optic tiltmeter system has been developed successfully. A low-cost light control unit has been developed to drive the system's optic and electronic components. From an experimental test, the fiber optic tiltmeter is proven to be a prospective sensor for the monitoring of the tilting angle of civil structure with a good linearity. Finally, the test also successfully demonstrates the performance and the potential of the novel fiber optic tiltmeter system to monitor the health of civil infrastructures.

• Korean Journal of Materials Research
• /
• v.27 no.1
• /
• pp.43-47
• /
• 2017

E (Electric) -glass fibers are the most widely used glass fibers, taking up 90 % of the long glass fiber market. However, very few papers have appeared on the physical characteristics of E-glass fibers and how they depend on the fiberizing temperature of fiber spinning. Glass fiber was fabricated via continuous spinning process using bulk E-glass. In order to fabricate the E-glass specimen, raw materials were put into a Pt crucible and melted at $1550^{\circ}C$ for 2hrs; mixture was then annealed at $621{\pm}10^{\circ}C$ for 2hrs. The transmittance and adaptable temperature for spinning of the bulk marble glass were characterized using a UV-visible spectrometer and a viscometer. Continuous spinning was carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of $1175{\sim}1250^{\circ}C$, while the winder speed was fixed at 500 rpm. Subsequently we investigated the physical properties of the E-glass fiber. The average diameter of the synthesized glass fiber was measured by optical microscope. The mechanical properties of the fiber were confirmed using a UTM (universal materials testing machine); the maximum tensile strength was measured and found to be $1843{\pm}449MPa$ at $1225^{\circ}C$.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.08a
• /
• pp.280-281
• /
• 2001