• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.561-568
• /
• 2017

In order to effectively utilize the Coarse Wavelength Division Multiplexing(CWDM) technology in optical integrated devices, a design of a wavelength selective coupler structure between an optical fiber and an optical waveguide in a flat substrate is can be considered. In this paper, we consider the coupling between a silicon waveguide with an air trench and a single mode fiber. We investigated the tendency of coupling efficiency and its limitations according to the grating depth. For this purpose, the coupling efficiency of coupler structure designed through modeling based on coupled mode theory is predicted and quantitatively compared with simulation results using finite element method.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.931-936
• /
• 1997

Optical fiber sensor is a subject which has been attracted considerable attention in recent years. Detection of sound pressure with optical fibers positioned in the arms of a Mach-Zehnder interferometer is presented in this paper. A fiber length of the order of 150m is wounded is made by hollow cylinder type. To increase the sound signal 3${\times}3$ directional coupler is used. Fiber optic hydrophone is the underwater tank with 2kHz sound source. Finally, it is shown that the fiber optic hydeophone can stably detec 2kHz sound.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1117-1122
• /
• 2005

This paper is studied the high-repetition rate optical-pulse stream generation using optical loop mirror coupler. With the recent development of the ultrahigh-speed optical time division multiplexed system, hish-repetition rate optical-pulse stream generation is necessary. This is different from conventional approaches, which use fiber or integrated waveguide delay line circuits. The high-repetition-rate optical-pulse multiplication phenomenon occurs when the optical pulse's spectral width is greater than the transfer bandwidth of the coupler used. From the analysis, the output repetition rate can be controlled by using fiber couplers with different equivalent transfer bandwidths. The pulse separation spacing is controlled by number of cascaded coupler in optical loop mirror coupler scheme.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.7-13
• /
• 2009

By incorporating a polarization beam splitter and fiber coupler, we propose a fiber-optic multiwavelength-switchable interleaving filter that can function as a polarizaiton-independent transmission or reflection-type one. The proposed filter consists of a polarizaiton beam splitter and a Sagnac birefringence loop that is composed of a 50:50 coupler, polarizaiton-maintaining fibers, and two quarter-wave plates. In the proposed filter, a transmission-type filter with a channel isolation > 18[dB] or a reflection-type one with a channel isolation ~3[dB], whose channel spacing and switching displacement were 0.8 and 0.4[nm] in common, respectively, could be obtained. Channel interleaving operation could be performed by the proper control of waveplates within the Sagnac birefringence loop.

• Journal of Sensor Science and Technology
• /
• v.13 no.5
• /
• pp.350-355
• /
• 2004

A novel UV sensor was manufactured and characterized using the evanescentfield coupling between fiber-planar waveguide (PWG) coupler and prism. A spiroxazine dye was chosen as planar waveguide because its photochromic isomerization induced by UV irradiation. A novel UV sensor was proposed to measure the variation of refractive index and absorption coefficient simultaneously. The wavelength responses of these sensors by UV exposure times were measured 0.48 nm/sec, 0.757 nm/sec, and ATR output power variations were measured $-0.424{\mu}W$/sec and $-0.62{\mu}W$/sec when UV exposure power were 3 mW and 5 mW, respectively.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.49-51
• /
• 2003

This test data informs to compare components from different manufactured coupler type. On the point of reliability, less than 1x8 output branching number, fuse type coupler was more stable than PLC type coupler. But more than 1x8 output branching number, PLC type coupler was more stable. This test data showed critical branching point, on the point of reliability.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.484-487
• /
• 2004

Symmetric directional couplers are widely used in interferometers, switches, and various signal processing devices. Recently, several optical couplers using multimode fibers were reported, but these suffer from inefficient coupling of light into a branching fiber and/or low directivity. This paper presents the measurement and analysis of loss in the connection of optical fibers via the optical directional couplers. The functionality of the device is based on the principle that is symmetrical, the power in excited mode can be unambiguously directed into one of the output channel by varying and of its parameters. In this experiment, we measure the power of loss in the optical directional coupler at various radius of curvature. Before the measurement of loss in x-coupler, we polish the contact of the fiber surface in order that light can penetrate through another port. The results show that, when the radius of curvature is increased, the loss power is decreased and also approaches of the straight line case.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.846-851
• /
• 2010

A liquid-air interface sensing system using the flat end surfaces of a fused-silica fiber coupler has been demonstrated. The principle is based on the additional optical loss caused by changing the refractive index of the external material at the boundary of the end face made of a fiber. The immersion characteristics of this system with respect to the different splitting ratios of the couplers were investigated to determine the sensitivity when it responses to water and air. These experimental data are very useful for selecting the coupling ratio of a coupler in order to develop a multiple sensing probe system. In the proposed sensor structure, it can be emphasize that the sensing probe can be appropriately arrayed on the basis of splitting ratio of the coupler. As a result, it is expected that the proposed liquid-air interface sensors can also be applied to monitor flooding that occurs in multiple areas at the same time.

• Korean Journal of Optics and Photonics
• /
• v.10 no.3
• /
• pp.248-253
• /
• 1999

In this paper, we have investigated a fiber type active coupler which utilizes the mode coupling between the side polished single mode optical fiber and the active multimode planar waveguide. The proposed device can be used for not only tunable wavelength filter or optical intensity modulator but also a tool for measuring optical properties of guiding material such as refractive index, birefringence, electro-optic coefficient, and thermo-optic coefficient. We gave designed and optimized a coupler structure using the BPM and fabricated the device using thermo-optic polymer as active planar waveguide overlay. The device showed that insertion loss was less then 0.5 dB, extinction ratio was -13 dB at the resonance wavelength, and the wavelength tunablity due to thermo-optic effect was -1.5 nm/$^{\circ}C$. The active coupler using thermo-optic effect can be used as a wavelength tunable filer, an optical intensity modulator and an optical sensor. pulses that are subsequently compressed by a dispersive optical fiber. Experimental results show that $sech^2$ shape pulses with a pulse width of ~14 ps and a time bandwidth product of ~0.34 are successfully generated at 10 GHz repetition rate. In contrast to other methods, such as higher order soliton compression, this approach does not depend on the optical power and thus shows promise for application to low-power lasers.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.4
• /
• pp.335-346
• /
• 1987

The principal reason for the backscattering in an optical fiber is the Rayleigh scattering which is caused by non-uniform density of structure material of an optical fiber and diameter variations of the optical fiber-core along an optical fiber axis. The backscattering signal which is detected by the optical time domain reflectometer system(O.T.D.R) conatains information about both tha actual decay of power and the diameter variation along the optical fiber. In this paper, the O.T.D.R. system with 2x2 fiber directional coupler, timing control unit and gated integrator is used to measure diameter variations of an optical fiber.