• 한국광학회지
• /
• 제14권4호
• /
• pp.466-472
• /
• 2003

본 논문에서는 서로 다른 길이의 광섬유 지연선로를 광 2${\times}$2 MEMS 스위치로 선택하여 위상 배열 안테나의 각 안테나 소자에 급전되는 RF 신호의 위상을 고속으로 제어할 수 있는 광 실시간 지연선로의 구조를 제안하였다. RF 신호의 주사 방향이 8개인 10 GHz 선형 위상 배열 안테나용 광 실시간 지연선로를 구현하였으며, 실험 결과 최대 시간 지연 오차가 0.2 ps이하, 즉 최대 주사 각 오차 0.84$^{\circ}$로 측정되었다. 또한 제안된 실시간 지연선로에 의해 구동되는 8개의 마이크로 스트립 패치 안테나 소자로 구성된 10 GHz용 선형 위상배열 안테나를 설계하였고, 시뮬레이션을 이용하여 이 안테나의 방사 패턴을 분석하였다.

• 대한치과교정학회지
• /
• 제43권4호
• /
• pp.186-192
• /
• 2013

Objective: To analyze the fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro. Methods: Roots of human mandibular central incisors were covered with silicone, mimicking the periodontal ligament, and embedded in polymethylmethacrylate. The specimens (N = 50), with two teeth each, were randomly divided into five groups (n = 10/group) according to the retainer materials: (1) Interlig (E-glass), (2) everStick Ortho (E-glass), (3) DentaPreg Splint (S2-glass), (4) Ribbond (polyethylene), and (5) Quad Cat wire (stainless steel). After the recommended adhesive procedures, the retainers were bonded to the teeth by using flowable composite resin (Tetric Flow). The teeth were subjected to 10,00,000 cyclic loads (8 Hz, 3 - 100 N, $45^{\circ}$ angle, under $37{\pm}3^{\circ}C$ water) at their incisoproximal contact, and debonding forces were measured with a universal testing machine (1 mm/min crosshead speed). Failure sites were examined under a stereomicroscope (${\times}40$ magnification). Data were analyzed by one-way analysis of variance. Results: All the specimens survived the cyclic loading. Their mean debonding forces were not significantly different (p > 0.05). The DentaPreg Splint group (80%) showed the highest incidence of complete adhesive debonding, followed by the Interlig group (60%). The everStick Ortho group (80%) presented predominantly partial adhesive debonding. The Quad Cat wire group (50%) presented overlying composite detachment. Conclusions: Cyclic loading did not cause debonding. The retainers presented similar debonding forces but different failure types. Braided stainless steel wire retainers presented the most repairable failure type.

• 한국의류학회지
• /
• 제33권7호
• /
• pp.1121-1127
• /
• 2009

This study presents an eco-friendly and one-step finishing method for modifying fiber property that reduces fiber damage in wool/polyester blend fabrics. Lipase from aspergillus oryzae is used in this experiment. The enzymatic treatment condition is optimized by measuring the relative activity of lipase depending on pH level, temperature, concentration of lipase, and treatment time. The concentration of $CaCl_2$as an activator is determined by the characteristics including whiteness, water contact angle (WCA), and dyeing property. The modified properties of lipase treated fabrics are tested for pill resistance and surface morphology. The results are described as follows: the optimum condions for lipase treatment constitute a pH level of 8.0, treatment temperature of 40$^{\circ}$$_C$, concentration of lipase at 100% (o.w.f), and a treatment time of 90 minutes. $CaCl_2$helps in raising lipase activation, and the optimum concentration is 50mM. The whiteness, wet ability, and pill resistance of lipase treated fabrics improves as compared to the control. The dyeing property of lipase treated fabrics improved by 53.5% after using the one-bath dyeing method. This means that lipase treatment can save time and cost during the dyeing process since lipase treatment modifies wool and polyester fibers. The surface of lipase treated wool fibers do not exhibit any change, however voids and cracks manifest on the surface of lipase treated polyester fibers.

• Journal of the Korean Wood Science and Technology
• /
• 제44권6호
• /
• pp.828-841
• /
• 2016

Relatively little information is available regarding the correlation between wood and veneer quality, especially for Samama wood, an endemic wood species in eastern Indonesia. This study addresses the quality of 8 years old Samama wood and its effect on the veneer quality. Samama wood quality was determined by evaluating its specific gravity, moisture content, fiber dimensions, and microfibril angle from pith toward bark. Meanwhile, veneer quality was assessed by examining veneer thickness and lathe check characteristics. Geometry factor model was constructed to elaborate the quantities of lathe check from pith toward bark. Results show that fair variations of veneer thickness, ranging from 1.5 mm to 3.0 mm, could be obtained from Samama wood. The quantity, depth, and length of lathe check were noticeably decreasing toward bark. Further, in the same manufacturing process, geometry factor was determined as the dominant factor over other wood properties in affecting the frequency of lathe checks from pith towards bark. These facts should be put into consideration in producing veneer from Samama wood. Moreover, these results enlighten the potential of Samama wood as plywood and other excellent veneer-based products.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.67-74
• /
• 2016

The demand of environmental friendly packaging materials such as pulp mold has been increased. The application of the oil palm biomass, EFB (Empty Fruit Bunch) fiber as natural raw materials to the pulp mold could increase the usability of the pulp mold by the reduced production cost brought from the relatively low cost of EFB. The effects of the EFB(Empty Fruit Bunch) fibers on the properties of pulp mold and on the process efficiency were evaluated in this study. The pulp mold samples were prepared with mixture ONP (Old news paper) and EFB by using laboratory wet pulp molder. The changes in the drying efficiency were measured with the changes in the solid contents of pulp mold samples during drying process. The efficiency of the surface coating treatment on the pulp mold depending on the condition of the pulp mold samples were also evaluated in order to improve the water resistance properties of pulp mold. The addition of EFB increased the drying efficiency by providing the bulkier structure and the higher water contact angle, which indicated the better water resistance properties. The water resistance were improved by the surface coating treatments and the application of surface coating on the pulp mold at the higher moisture contents resulted in the higher improvement in the water resistance. The bulkier structure originated from the application of EFB fiber reduced the effects of the surface coating, which could be overcome by the control of surface coating process.

• 한국전자파학회논문지
• /
• 제8권3호
• /
• pp.254-263
• /
• 1997

通信 및 電子훌業의 發達에 따라, 電磁波放射에 對한 밟素鐵維彈化樹(CFRTP)의 電磁波 避廠效果(SE)를 冊究하는 것은 重要하다. 本R究에서는 밟素熾維(CF)의 避빼옷效果를 電波8홉室內에서, 驗的으로 測定하였다. 使用한 樹服는 PC, PP, PEl, PMMA 및 PA이다. 實嚴은 分光分析器에 의해 鋼避蘇箱子와 모노폴안테나를 使用해 修行하였다. 훌훌結果로부터 CF는 良好한 電磁波適嚴材의 한 候補임을 알 수 있었다. SE는 CF의 積層의 增加에 따라 增加하였다. 徵小한 揚傷의 增加는 CF의 平面密度, 透過두께 및 反射角의 增加로 인해 SE를 增加 시켰다. SE에 미치는 다른 特性들은 母材樹服, 안테나問의 距離 및 노이즈의 周波數에 따라 달랐다.

• 한국의류산업학회지
• /
• 제15권6호
• /
• pp.985-992
• /
• 2013

Polytrimethylene terephthalate(PTT) offers several advantageous properties such as good tensile strength, uniformity, stiffness, toughness, UV stability, resilience, stain resistance, outstanding elastic recovery, and dyeability. The effects of annealing temperature on physical properties and the structure of PTT filaments and yarn were investigated by measuring wide-angle X-ray diffraction (WAXD), density, optical birefringence, dynamic visco elasticity, and tensile testing. The intensity of maximum tan ${\delta}$ decreased and the temperature of maximum tan ${\delta}$ shifted to a higher temperature as the annealing temperature of filaments increased; however, it shifted to a lower temperature when the annealing temperature exceeded $130^{\circ}C$. In addition, crystallinity, density and D-spacing of (010) crystal face increased as the annealing temperature increased. Optical birefringence and specific stress were almost constant up to $100^{\circ}C$ and then decreased above $130^{\circ}C$. The shrinkage of PTT filament is 0 in boiling water when annealed above $130^{\circ}C$; consequently, the use of annealed fiber above $130^{\circ}C$ can remove thermal instability when dyeing PTT fiber. In the case of yarns, the thermal stability and physical properties of yarns showed the best effect when the ply number is less than 5, twist number is less than 400tpm, and the annealing time is 20minutes.

• Smart Structures and Systems
• /
• 제15권6호
• /
• pp.1393-1410
• /
• 2015

An original sensor system based on Fiber Bragg Gratings (FBG) for the strain monitoring of an adaptive wing element is presented in this paper. One of the main aims of the SARISTU project is in fact to measure the shape of a deformable wing for performance optimization. In detail, an Adaptive Trailing Edge (ATE) is monitored chord- and span-wise in order to estimate the deviation between the actual and the desired shape and, then, to allow attaining a prediction of the real aerodynamic behavior with respect to the expected one. The integration of a sensor system is not trivial: it has to fit inside the available room and to comply with the primary issue of the FBG protection. Moreover, dealing with morphing structures, large deformations are expected and a certain modulation is necessary to keep the measured strain inside the permissible measure range. In what follows, the mathematical model of an original FBG-based structural sensor system is presented, designed to evaluate the chord-wise strain of an Adaptive Trailing Edge device. Numerical and experimental results are compared, using a proof-of-concept setup. Further investigations aimed at improving the sensor capabilities, were finally addressed. The elasticity of the sensor structure was exploited to enlarge both the measurement and the linearity range. An optimisation process was then implemented to find out an optimal thickness distribution of the sensor system in order to alleviate the strain level within the referred component.

• 마이크로전자및패키징학회지
• /
• 제13권2호
• /
• pp.1-7
• /
• 2006

본 논문에서는 솔더 레지스트(solder resist)의 두께와 코어의 물성에 따른 인쇄회로기판의 철의 크기와 형상에 대하여 연구하였다. 인쇄회로기판의 굽힘 변형은 적층되는 재료의 열팽창계수의 차이에 의해 발생한다. 따라서 굽힘 변형의 감소를 위해서는 열팽창계수의 차이가 작은 적층 재료를 사용하는 것이 필요하며, 구조 형상에서도 상면과 하면의 불균일성을 완화시킬 필요가 있다. 또한, 적층 재료에서 코어의 강성을 높여 점의 발생을 억제할 수 있다. 코어를 이루는 복합재료는 적층 순서와 섬유 각에 따른 물성 특성의 방향성에 따라 굽힘과 비틀림이 연성되는 현상을 보이며, 이와 같은 성질을 이용하면 휨을 제어할 수 있다. 본 연구에서는 2층으로 구성된 chip scale package (CSP) 기판의 휨에 대한 연구로, 실험 및 유한 요소해석 툴을 이용하여 개선 결과를 도출하였다.

• Journal of Mechanical Science and Technology
• /
• 제18권1호
• /
• pp.65-73
• /
• 2004

Composites are a material class for which nondestructive material property characterization is as important as flaw detection. Laminates of fiber reinforced composites often possess strong in-plane elastic anisotropy attributable to the specific fiber orientation and layup sequence when waves are propagating in the thickness direction of composite laminates. So the layup orientation greatly influences its properties in a composite laminate. It could result in the part being .ejected and discarded if the layup orientation of a ply is misaligned. A nondestructive technique would be very beneficial, which could be used to test the part after curing and requires less time than the optical test. Therefore a ply-by-ply vector decomposition model has been developed, simplified, and implemented for composite laminates fabricated from unidirectional plies. This model decomposes the transmission of a linearly polarized ultrasound wave into orthogonal components through each ply of a laminate. Also in order to develop these methods into practical inspection tools, motorized system have been developed for different measurement modalities for acquiring ultrasonic signals as a function of in-plane angle. It is found that high probability shows between the model and tests developed in characterizing cured layups of the laminates.