• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.3
• /
• pp.123-131
• /
• 2007

The buckling behavior of a fiber reinforced plastic pipe was researched. When a cylindrical structure is made of isotropic material, it shows two dimensional buckled shape which has same deformed section along the longitudinal direction. But an anisotropic cylindrical structure shows three dimensional buckled shape which has different deformed section along the longitudinal direction. Because the modulus of elasticity is varied in a certain direction when ply angles are changed, the strength of a pipe are changed as ply angles are changed. In this study, the limitation of two dimensional and three dimensional buckling mode was investigated and the buckling strength of a laminated composite pipe was evaluated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1768-1775
• /
• 2004

The compressive axial collapse tests were performed to investigate collapse modes and energy absorption characteristics of Al/CFRP compound tubes which are aluminum tubes wrapped with CFRP(Carbon Fiber Reinforced Plastics) outside the aluminum circular and square tubes. Based on collapse characteristics of aluminum tubes and CFRP tubes respectively, the axial collapse tests were performed for Al/CFRP compound tubes which have different CFRP orientation angles. Test results showed that Al/CFRP compound tubes supplemented the unstable brittle failure of CFRP tubes due to ductile nature of inner aluminum tubes. In the light-weight aspect, specific energy absorption were the highest for Al/CFRP, CFRP in the middle, and aluminum the lowest. Also, specific energy absorption of circular tubes was higher than square tubes'. It turned out that CFRP orientation angle of Al/CFRP compound tubes influence specific energy absorption together with the collapse modes of the tubes.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.6
• /
• pp.205-211
• /
• 2007

In this paper, foam-composite sandwich structures for EDM machine tool components such as column and column block designed by controlling stacking sequences and cross-sectional dimensions of the composite structures. The original column block is a box-shaped structure made of aluminum connecting a column and a Z-stage of the system. This research was focused on the design of efficient column block structure using a foam-composite sandwich structure which have good bending stiffness and damping characteristics to reduce the mass and increase damping ratio of the system. Vibration tests for getting damping ratio with respect to the stacking angle and thickness of the composites were carried out. Finite element analyses for static defection and vibration behaviour were also carried out to find out the appropriate stacking conditions; that is, stacking sequence and rib configuration. From the test and analysis results it was found that composite-foam sandwich structures for the microfactory system can be successful alternatives for high precision machining.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.299-308
• /
• 2001

This paper presents the three-dimensional (3-D) study of the natural vibration of cantilevered laminated composite plates. The Ritz method is used to obtain stationary values of the associated Lagrangian functional with displacements approximated by mathematically complete polynomials satisfying the boundary conditions at the clamped edge exactly. The accuracy of the 3-D model is established through a convergence study of non-dimensional frequencies followed by a comparison of the converged 3-D solutions with analytical and experimental findings in the existing literature. A wide scope of 3-D frequency results explain the influence of a number of geometrical and material parameters for cantilevered laminated plates, namely aspect ratio (a/b), width-to-thickness ratio (a/h), orthotropy of material, number of plies (NP), fiber orientation angle(θ), and stacking sequence.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.340-346
• /
• 2000

Traveling wave type semiconductor optical amplifiers integrated with spot-size-converter (SSC-TW-SOA) have been extensively studied for the improvement of coupling effiClency With single-mode fiber and fO! the cost reducClon 111 a packaging In tlIis paper the slructural dependence of the spot-slZe-converter on the effective facet reflectlvllY $R_{eff}$ was experimentally as well as thcoretienlly mvestlgated. It was shown that not only a sufficient mode-conversion in a sse region along the latersl and tran~verse directions but also an introductIOn of angled-facet were very essential in order to reduce $R_{eff}$ Very small ripple less than 0.1 dB in an amplified spontaneous emission spectrum was observed with the fabncated SSC-lW-SOA which consists of the wrndow length of $20\mu\textrm{m}$, facet angle of $7^{\circ}$, and antlrelleetioll-coated facet of ] % reflectivity.tivity.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.5
• /
• pp.373-378
• /
• 1999

In order to analyse the degradation mechanism of polymer materials for outdoor condition, FRP laminate was exposed to high temperature and ultraviolet rays. Then, thedegradation process was evaluated by comparing contact angle, surface potential decay, and polarity effect respectively. Especially, the analysis of surface degradation phenomena by corona charging method showed the exact correlation with the result of chemical properties. Therefore we can confirm that the application of corona charging method on the identification of degradation process is very useful. If this method is usedin degradation studies on the polymer surface, it will be more effective on the surface analysis of polymer insulators. With corona charging method and chemical spectrum analysis, it was possible concretely to define degradation process on the polymer surface exposed at the situation of different environmental conditions.

• The Journal of Korea Robotics Society
• /
• v.12 no.1
• /
• pp.26-32
• /
• 2017

Previous shape sensors including bend sensors and optic fiber based sensors are widely used in various applications including goniometer and surgical robots. But theses sensors have large nonlinearity, limited in the range of sensing curvature, and sometimes are expensive. This study suggests a new concept of bend sensor using cable-conduit which consists of the outer sheath and the inner wire. The outer sheath is made of helical coil whose length of the central line changes as the sheath bends. This length change of the central line can be measured with the length change of the inner cable. The modeling and the experimental results show that the output signal of the proposed sensor is linearly related with the bend angle of the sheath with root mean square error of 5.3% of $450^{\circ}$ sensing range. Also the polynomial calibration of the sensor can decrease the root mean square error to 2.1% of the full sensing range.

• 보존과학연구
• /
• s.11
• /
• pp.87-105
• /
• 1990

Chemical and micro morphological changes of archaeological waterlogged woods from shipwrecked materials in marine situations were investigated which were submerged in seabed for over 900 years. Tested Wood species were Pinusdensiflora, Zelkova serrata, Quercus acutissima and Camellia japonica. The obtained results were summarized as follows; Chemical analysis showed that lignin content was increased, whereas the amout of holocellulose was heavily decreased in the degraded archaeological lwoods(DAW), when compared to the recent woods. The amount of alkalineextractives in the DAW was extremley high. IR spectra showed that disappearance of absortion band at $1,730㎝^-1$ intensity increase at 1,600, 1,500 and $1,270㎝^-1$ and the emergence of single band around $1,050㎝^-1$.Microscopic investigation showed that cell wall of latewood tracheids and fiber in the DAW were severely degraded while, early wood tracheids less degraded. Degradation in the cell wall was mainley occurred in $S_2$layer, while the middle lamella was the least degraded. The micro morphological characteristics of DAW were separation of secondary wall from middle lamella, cavities aligned with micro fibril angle in $S_2$layer and granular appearance of secondary wall by the bacterial attack.

• Macromolecular Research
• /
• v.15 no.5
• /
• pp.449-458
• /
• 2007

The aims of this study were to investigate the intercalation of polymer chains with organoclays and improve the thermo-mechanical properties of poly(butylene terephthalate) (PBT) hybrids by comparing PBT hybrids synthesized using two different organoclays. The organoclays; dodecyltriphenylphosphonium-montmorillonite ($C_{12}PPh-MMT$) and dodecyltriphenylphosphonium-mica ($C_{12}PPh-Mica$), were used to fabricate the PBT hybrid fibers. Variations in the properties of the hybrid fibers with the organoclays within the polymer matrix, as well as the draw ratio (DR), are discussed. The thermo-mechanical properties and morphologies of the PBT hybrid fibers were characterized using differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray diffraction, electron microscopy and mechanical tensile properties analysis. The nanostructures of the hybrid fibers were determined using both scanning and transmission electron microscopies, which showed some of the clay layers to be well dispersed within the matrix polymer, although some clustered or agglomerated particles were also detected. The thermal properties of the hybrid fibers were found to be better than those of the pure PBT fibers at a DR = 1. The tensile mechanical properties of the $C_{12}PPh-MMT$ hybrid fibers were found to worsen with increasing DR. However, the initial moduli of the $C_{12}PPh-Mica$ hybrid fibers were found to slightly increase on increasing the DR from 1 to 18.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.278-281
• /
• 2004

The purpose of this paper is to show a reliable analytical method to predict the deflections of F/W Composite Motor Case. Structural analysis and testing of a Carbon/Epoxy Composites Motor Case for Pressure Loadings were performed. This paper presents the development of 3-D layered axi-symmetric solid element for finite element analysis. Finite element analyses were preformed considering fiber angle variation in longitudinal and thickness direction by ANSYS. The analytical results agree well with experimental results.