• Journal of Animal Environmental Science
• /
• v.20 no.3
• /
• pp.117-124
• /
• 2014

The objectives were to assess the use of near-infrared reflectance spectroscopy (NIRS) as a tool for estimating nutrient compositions of corn kernel, and to apply an NIRS-based indium gallium arsenide array detector to the system for collecting spectra and analyzing calibration equations using equipments designed for field application. Partial Least Squares Regression (PLSR) was employed to develop calibration equations based on representative data sets. The kennard-stone algorithm was applied to induce a calibration set and a validation set. As a result, the method for structuring a calibration set significantly affected prediction accuracy. The prediction of chemical composition of corn kernel resulted in the following (kennard-stone algorithm: relative) moisture ($R^2=0.82$, RMSEP=0.183), crude protein ($R^2=0.80$, RMSEP=0.142), crude fat ($R^2=0.84$, RMSEP=0.098), crude fiber ($R^2=0.74$, RMSEP=0.098), and crude ash ($R^2=0.81$, RMSEP=0.048). Result of this experiment showed the potential of NIRS to predict the chemical composition of corn kernel.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.655-662
• /
• 2019

This study evaluated the multi-bonding performances of timbers as well as those of reinforcement and timber to obtain data for preparing guidelines regarding the use of timbers as large structural members. For the multi-bonding performances of timbers, four types of bonding surfaces were prepared according to the pith position. For the bonding performances of FRP (fiber-reinforced plastic)/steel plate and timber, a total of 11 types of specimens were produced for the selection of the appropriate adhesive. The bonding performances of the produced specimens were evaluated through a water soaking delamination test, a water boiling delamination test, and a block shear strength test. The test results showed that the bonding strength of the bonding surface according to the pith position was highest in the specimen for which the two sections with the pith at the center of the cross-section on timber and between the bonding surfaces (the tangential and radial sections were mixed) were bonded. Furthermore, the specimens for which the section (radial section) with the pith on the bonding surface of the timber was bonded showed a high delamination percentage. The results of the block shear strength test showed that the bonding section did not have a significant effect on the shear strength, and that the measured wood failure percentage was higher than the KS standard value. The PVAc adhesive showed the highest bonding strength between larix timber and GFRP (glass FRP). Furthermore, the epoxy and polyurethane adhesives showed good bonding strength for CFRP (carbon FRP) and structure steel, respectively.

• Smart Structures and Systems
• /
• v.26 no.6
• /
• pp.681-692
• /
• 2020

Conventional Piezoelectric Energy Harvesters (CPEH) have been extensively studied for maximizing their electrical output through material selection, geometric and structural optimization, and adoption of efficient interface circuits. In this paper, the performance of Stepped Piezoelectric Energy Harvester (SPEH) under harmonic base excitation is studied analytically, numerically and experimentally. The motivation is to compare the energy harvesting performance of CPEH and SPEHs with the same characteristics (resonant frequency). The results of this study challenge the notion of achieving higher voltage and power output through incorporation of geometric discontinuities such as step sections in the harvester beams. A CPEH consists of substrate material with a patch of piezoelectric material bonded over it and a tip mass at the free end to tune the resonant frequency. A SPEH is designed by introducing a step section near the root of substrate beam to induce higher dynamic strain for maximizing the electrical output. The incorporation of step section reduces the stiffness and consequently, a lower tip mass is used with SPEH to match the resonant frequency to that of CPEH. Moreover, the electromechanical coupling coefficient, forcing function and damping are significantly influenced because of the inclusion of step section, which consequently affects harvester's output. Three different configurations of SPEHs characterized by the same resonant frequency as that of CPEH are designed and analyzed using linear electromechanical model and their performances are compared. The variation of strain on the harvester beams is obtained using finite element analysis. The prototypes of CPEH and SPEHs are fabricated and experimentally tested. It is shown that the power output from SPEHs is lower than the CPEH. When the prototypes with resonant frequencies in the range of 56-56.5 Hz are tested at 1 m/s2, three SPEHs generate power output of 482 μW, 424 μW and 228 μW when compared with 674 μW from CPEH. It is concluded that the advantage of increasing dynamic strain using step section is negated by increase in damping and decrease in forcing function. However, SPEHs show slightly better performance in terms of specific power and thus making them suitable for practical scenarios where the ratio of power to system mass is critical.

• Steel and Composite Structures
• /
• v.43 no.4
• /
• pp.447-456
• /
• 2022

Recent experimental studies showed that deep steel I-shaped profiles classified as high ductility class sections in seismic design international codes exhibit low deformation capacity when subjected to cyclic loading. This paper presents an innovative retrofit solution to increase the rotation capacity of beams using bonded carbon fiber reinforced polymers (CFRP) patches validated with advanced finite element analysis. This investigation focuses on the flexural cyclic behaviour of I-shaped hot rolled steel deep section used as beams in moment-resisting frames (MRF) retrofitted with CFRP patches on the web. The main goal of this CFRP reinforcement is to increase the rotation capacity of the member without increasing the overstrength in order to avoid compromising the strong column-weak beam condition in MRF. A finite element model that simulates the cyclic plasticity behavior of the steel and the damage in the adhesive layer is developed. The damage is modelled using the cohesive zone modelling (CZM) technique that is able to capture the crack initiation and propagation. Details on the modelling techniques including the mesh sensitivity near the fracture zone are presented. The effectiveness of the retrofit solution depends strongly on the selection of the appropriate adhesive. Different adhesive types are investigated where the CZM parameters are calibrated from high fidelity fracture mechanics tests that are thoroughly validated in the literature. This includes a rigid adhesive commonly found in the construction industry and two tough adhesives used in the automotive industry. The results revealed that the CFRP patch can increase the rotation capacity of a steel member considerably when using tough adhesives.

• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.801-811
• /
• 2022

In this study, we constructed a database of dyeing concentrations of all reactive dyes used for dyeing linen according to the thickness of the linen fabric and attempted to improve the reproducibility of the dyeing process for the commercialization of linen fabric materials. Linen fabric is a natural cellulose material that is comfortable and suitable for eco-friendly trends. It is a typical summer material with excellent breathability and thermal conductivity, quick moisture absorption and dissipation, and a cool touch. Dyeability and fastness were evaluated depending on the thickness of the linen fabric using a monochlorotriazine (MCT) reactive dye and bifunctional yellow, red, and blue dyes. All three colors of the MCT reactive dye and bifunctional dyes exhibited a darker shade as the fiber thickness of the marker increased. Fastness to washing was excellent at grades 4-5 or higher, regardless of the color of the dye and the number of linen fabrics. Although some color-fastness differences were noted, with the color change occurring most frequently with blue color, the fastness variations with dye type were mostly similar. The results of this study are expected to facilitate the selection of reactive dyes according to the thickness of the linen fabric based on the basic data from the laboratory, which will aid in the mass production of linen fabric and benefit the fashion industry.

• Journal of the Korean Society of Food Culture
• /
• v.22 no.3
• /
• pp.323-329
• /
• 2007

The objective of this study was to compare the healthy dining out attitude of restaurant diners by self-rated health status. Using healthy dining attitude and behavior questionnaire and a single question describing self-rated health status, the needs and importance of healthy dining out was detected. Mean age of the 182 respondents was 38.9${\pm}$11.37 years old and 37.4% of the respondents answered their mean monthly income was over 6,000,000won showing the subjects belonged in high income diners. The needs of healthy dining measured by five scales and offering healthy menus(3.80), labeling foods about original country(3.79), using environmentally friendly foodstuffs(3.71) and labeling nutrients on menu board(3.62) show higher score than others. A total of 76.4% of the respondents assessed their health status as 'good-rated Health' and 23.6% was 'poor-rated health'. There was no difference in frequency of eating out by self-perception of health status but, the 'poor-rated health' group need more nutrition information in restaurant specially for calorie(p<0.05), cholesterol(p<0.05), fiber(p<0.05), functional nutrients(p<0.001) showing significant differences comparing to 'good-rated health' group. In good-rated health group, selection of Korean cuisine for eating out was more frequent than the poor. The results shows the needs of healthy dining can be varied by diner's health status and therefore restaurateur should focus on understanding of the needs of diners with various health status.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.68 no.3
• /
• pp.175-187
• /
• 2023

Peanuts, also known as groundnuts (Arachis hypogaea L.), are globally recognized as a vital oilseed crop. Peanuts are rich in proteins (e.g., arginine), oils (e.g., oleic acid and linoleic acid), fiber, vitamins (e.g., niacin and tocopherol), and carbohydrates and are consumed worldwide. However, the presence of aflatoxin (AF) has garnered substantial attention since its initial discovery as the causative agent of Tukey's X disease in the United Kingdom in 1960. Among the 18 aflatoxins identified, aflatoxin B₁ (AFB₁) has the highest toxic activity and causes hepatocellular carcinoma. It is classified as Group I by the International Agency for Research on Cancer (IARC) of the World Health Organization (WHO). The present study was conducted to evaluate aflatoxin B₁ resistance of 102 peanut accessions and select putative aflatoxin B₁-resistant peanut accessions to aflatoxin B₁. One hundred and one Korean germplasms harvested in 2020 were inoculated with A. flavus to identify aflatoxin-resistant cultivars, and the aflatoxin B₁ concentration was measured using an ultra-performance liquid chromatography-photodiode array detector. Twenty-six accessions with aflatoxin B₁ concentrations lower than those of the check plant 55-437 were chosen for the development of aflatoxin-resistant varieties in Korea. As Korean aflatoxin-resistant varieties have not yet been developed, the findings of the present study are expected to provide useful information for the development of aflatoxin-resistant cultivars.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.1
• /
• pp.26-31
• /
• 2022

This study was carried out to evaluate the growth characteristics and forage yield potential for warm season grass as emergency forages. The experimental design was a randomized block design (RBD) with three replications. Two barnyard millet (Echinochloa species cv. Shirohie and Jeju native), a pearl millet (Pennisetum glaucum cv Feed milk 2) a proso millet (Panicum miliaceum cv Native), a teffgrass (Eragrostis tef cv. Tiffany) and a kleingrass (Panicum coloratum cv. Selection 75) were compared for forage production and quality at the Mid regions of Korea. Warm season forage crops were sown on May 21 and June 23 respectively, and in 2021, it was sown twice on May 21 and June 21 The number of days to seedling emergence for barnyard millet and teffgrass was observed approximately 10 and 3 days after seeding, respectively. The cultivation period from seeding to harvest was within 60 days for all entry spices except for the late-heading type barnyard millet (within 84 days). As for the dry matter yield by seeding date, the dry matter yield of the late-heading type barnyard millet in May seeding was the highest at 23,872 kg/ha, and the kleingrass was the lowest at 3,888 kg/ha. For the June seeding, the dry matter yield of the late-heading type barnyard millet was 17,032 kg/ha, the highest, and the proso millet, teffgrass and kleingrass showed the lowest at 5,468, 5,442, and 5,197 kg/ha, respectively. The crude protein (CP) content was varied by warm season grass species, but the early-heading type barnyard millet, teffgrass, and kleingrass showed the highest tendency, and the late-heading type barnyard millet showed the lowest at 5.7~5.9%. Neutral detergent fiber (NDF) and acid detergent fiber (ADF) content did not show a significant difference between the seeding in May, but kleingrass in June sowed lower than the others.

• Korean Journal of Food Science and Technology
• /
• v.48 no.3
• /
• pp.256-261
• /
• 2016

This study investigated the changes in functional components of barley powder produced from different grain varieties (Dahan, Hinchalssalbori, Heukgwang, Huknuri and Boseokchal) and varying milling degrees (27, 23, 19, and 15%). Total polyphenol contents increased with a decrease in the milling degree, with content ranges of 0.97-1.40, 1.19-1.66, 1.22-1.77, 1.30-1.93, and 1.46-2.12 mg/g, respectively. Total flavonoids content also increased with a decrease in the milling degree. The total polyphenol and flavonoids contents were the highest in barley powder from Huknuri and Boseokchal grains. Total dietary fiber, arabinoxylan, and GABA contents increased with a decrease in the milling degree. As the milling degrees decreased, ${\beta}$-glucan contents, which was the highest in Hinchalssalbori and Boseokchal, decreased with ranges of 4.98-7.29, 5.26-7.03, 4.84-7.17, 4.84-700, and 4.66-6.33 mg/100 g, respectively. These results provide useful data for selection of an appropriate variety and milling degree to achieve a high quality in barley processing.

• Korean Journal of Agricultural Science
• /
• v.43 no.5
• /
• pp.802-809
• /
• 2016

The objective of this study was to evaluate the nutritional value of commercial compound feeds for late finishing Hanwoo steers using detailed chemical analysis and an in vitro rumen fermentation trial. A total of 4 different feeds were selected and used to conduct a chemical analysis for their nutrient contents. The largest variation in nutrients contents among experimental feeds was found in ether extract and the smallest one was found in total digestible nutrients. Commercial feeds C and D had a higher energy value than the others. Even if C and D had a similar feed energy value, the components used to increase energy differed between them (non-fiber carbohydrate [NFC] for C; ether extract for D). In the in vitro trial, no significant difference was observed in dry matter in vitro digestibility and gas production between treatments. However, the highest ammonia concentration (p < 0.05) was observed in C and D feeds. The low acetate to propionate ratio observed in C feeds (p < 0.01) suggested that this feed had high starch based carbohydrates that NFC degrading bacteria used to produce more propionate. It is important to provide nutritional information to farmers so that they can select the appropriate commercial feeds to suit their own feeding strategies. This study might give supporting information to farmers for a more educated, and better, selection of feeds. Further in vivo studies should be conducted to evaluate the effects of different commercial feeds on growth performances in late finishing Hanwoo steers.