• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.998-1004
• /
• 2002

This paper reports a design of feedforward linear power amplifier using pilot tone for IMT-2000 band repeaters accepting multi-carrier. As this time pilot tone is applied to the circuit differently from the existing method. Only one pilot tone is used in both 1-st loop(IMD abstraction loop) and 2-nd loop(IMD cancellation loop) to cancell IMD signals automatically according to variation of frequency or power level of input signals. As an experiment, in range of 2110 MHz - 2170 MHz at LPA output power of $20 W_{avg}$, IMD characteristics of over 20 dB was improved maintaining below -60 dBc considering respective 20 MHz. Therefore the supposed feedforward linear power amplifier can be used for linear power amplifier in IMT-2000 band repeaters.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.341-344
• /
• 2000

Advanced FeedForward method use Predistortion method and FeedForward method simultaneously. This method better than original Feedforward method in linearity and supply smaller power to pre-power amplifier than different methods, and then it has higher power efficiency and better linearity than original Feedforward method. A linear power amplifier using Advanced feedforward method is designed and fabricated for IMT-2000 transmission system (2110㎒ -2170M㎓). This amplifier's power gain is about 40㏈ and it's 3-rd IMD(Intermodulation distortion) are smaller than about -55㏈c(@ 10MHz).

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.108-112
• /
• 2003

A feedforward amplifier, which is composed of several components, is an open loop system. Therefore, feedforward amplifiers are apt to deteriorate the performance according to the environmental changes even though the cancellation performance and the linearization bandwidth of feedforward systems are superior to other linearization methods. A control method is needed for maintaining the original performance of feedforward amplifiers or to keep the performance within a little error bounds. In this paper, an adaptive control method, which has a good convergence characteristic and is easy to implement, is suggested. The characteristics of the suggested control method compare with the characteristics of other control methods and the simulation results are presented.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.1-8
• /
• 1997

In this paper, we propose a new method for the improvement of linearizing and adaptive convergence charateristics of the feedforward linear power amplifier. In this circuit, errors at the signal cancellation stage can be compensated at the error cancellation stage and the overall linearizaton and adaptation characteristics of the linear amplifier are improved. The broadband characteristics and linearizing capability are improved without increasing the complexity of circuits and the signal processing structure.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.87-90
• /
• 2003

In this paper, A feedforward linear power amplifier is analyzed for imperfect signal cancellation and negative feedback for basestaion of IMT2000 band. the distortion generatied by the error amplifier is reduced using an imperfect signal cancellation for a 1-carrier WCDMA source by 4.3dB at 2.5MHz offset and 6dB at 5MHz offset of IMSR(intermodulation signal power ratio) compared to a perfect signal cancellation system. additionally, An imperfect signal cancellation using negative feedback improved 1.3dB and 8.2dB at 2.5MHz and 5MHz offset of IMSR compared to an imperfect signal cancellation.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.337-340
• /
• 2000

In this paper, I compared some characteristics between HPA and LPA using Feedforward method. Feedforward method is known for best IMD correction. HPA generated 46.5㏈c at 45.5㏈m output power. But, using feedforward linearing method, I could improve IMD to 67.17㏈c at the same output power. IMD could be improved 20.67㏈ at 45.5㏈m output power. I measured average power, IMD, total current, and efficiency of two amplifier at many different power levels. I could get about 70d3c IMD using feedforward method.

• Journal of Navigation and Port Research
• /
• v.26 no.3
• /
• pp.295-302
• /
• 2002

Currently digital communication system adapt various digital modulation schemes. All these communication systems are required to cause the minimum interference to adjacent channels, they must therefore employ the linear power amplifiers. In respect to linear power amplifiers, there are many linearization techniques. Feedforward power amplifier represent very wide bandwidth and high linearization capability. In the feedforward systems overall efficiency is reduced due to the loss of delay line. In this paper, delay filter instead of transmission delay line adapted to get more high efficiency. Experimental results showed that ACLR has improved 17.04dB which is added 2.54dB by using the delay filter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1059-1066
• /
• 2005

This paper reports an application of Doherty amplifier for efficiency improvement of feedforward power amplifier(FPA). For performance analysis, we measured 15 W average output power using WCDMA 4FA input signal with a center frequency 2.14 GHz. The applied Doherty amplifier presents the characteristics of high efficiency and low linearity in comparison to the class AB amplifier, and it was used as main amplifier of FPA fir efficiency improvement. To analyze the change of characteristic, tow Doherty amplifiers whose linearity and efficiency are different were applied. The applied FPAs are improved about $2\%$ or more performance in efficiency, but decreased in linearity on 15 W average output power. We additionally modified the coupling factor(CF) of the error loop and the error amplifier capacity for linearity improvement. Aa a result, the efficiency improvement and high linearity resulted from the change of CF and error amplifier capacity. However, we think if the linearity of Doherty amplifier were more than 35 dBc, the FPA would improve the performance about $2\%$ or more efficiency and maintain enough linearity.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.127-133
• /
• 2004

A feedforward amplifier, which is composed of several components, is an open loop system. Therefore, feedforward amplifiers are apt to deteriorate its performance according to the environmental changes even though the cancellation performance and the linearization bandwidth of feedforward systems are superior to other linearization methods. A control method is needed for maintaining the original performance of feedforward amplifiers or to keep the desired performance within a little error bounds. In this paper, an adaptive control method using the steepest descent algorithm, which has a good convergence characteristic and is easy to implement, is suggested. The characteristics of the suggested control method compare with the characteristics of other control methods and the simulation results are presented.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.3
• /
• pp.452-456
• /
• 2016

In this paper, a dual-channel readout amplifier array is realized in a standard $0.18{\mu}m$ CMOS technology for the applications of panoramic scan LADAR systems. Each channel consists of a PIN photodiode with 0.9 A/W responsivity and a 1.0 Gb/s readout amplifier(ROA). The proposed ROA shares the basic configuration of the previously reported feedforward TIA, except that it exploits a replica input to exclude a low pass filter(LPF), thus reducing chip area and improving integration level, and to efficiently reject common-mode noises. Measured results demonstrate that each channel achieves $70dB{\Omega}$ transimpedance gain, 829 MHz bandwidth, -22 dBm sensitivity for $10^{-9}BER$, -34 dB crosstalk between adjacent channels, and 45 mW power dissipation from a single 1.8 V supply.