• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.30-37
• /
• 2007

The injection and spray characteristics of top-feed type injector was investigated under liquid phase injection fueled with liquefied petroleum gas (LPG). Different pressures and temperatures of fuel injection system were tested to identify the injection characteristics after hot soaking. MIE-scattering technique was used for verification of successful liquid phase injection after hot soaking. In case of bottom-feed type injector, the injection was accomplished at every experimental condition. In case of top-feed type injector, when the pressure of LPG was over 1.2 MPa, the injection was not executed. However, under the pressure were 1.2 MPa, the liquid phase injection after hot soaking was accomplished. The engine with top-feed type fuel injection equipment was restarted successfully after hot soaking.

• Journal of Biosystems Engineering
• /
• v.19 no.4
• /
• pp.343-357
• /
• 1994

Current commercial dairy feed has various problems in low feed productivity, inadequate formulation and higher feeding cost due to excessive capital investment and non-specialized system for the end product. To solve those problems, 6 TMR terminal models were developed in this study. The developed TMR terminal system consists of TMR terminal, TMR main center and combined system linked TMR terminal and TMR main center. 15 TMR main center models were developed to support 10, 20, 30, 40, 50 TMR terminal(30 ton/day basis) by 3 different types, and evaluated for capital investment and operation cost by the analysis of the newly developed computer program. Optimum model size is analyzed and suggested for each model. Followings are summary of this study : 1. The capital investment costs of TMR main centers were 1,600 to 3,800 million won for type 1, 2,200 to 4,500 million won for type 2 and 2,200 to 4,800 million won for type 3. Also model MACE30 or bigger were justified as the economical models. 2. The feed production costs of TMR main center models were 3,166 to 4,824 won/ton for type 1, 3,816 to 6,182 won/ton for type 2 and 3,990 to 6,263 won/ton for type 3. So feed production cost range was 3,166 to 6,263 won/ton. 3. The bigger production capacity, the less TMR main center production cost. The feed production cost of the biggest model MACE50 was 62~65% of smallest model MACE10.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.17-28
• /
• 1994

Chip breaking is important in lathe work for maintaining good surface of the products and safety of operator. The purpose of this study is to investigate the performance of chip breaking and chip shape resulted from the carbide inserts with grooved type and obstruction type chip breaker. Experiments have been performed under the following cutting conditions, (1) constant cutting speed with variable depth of cut and feed rate, (2) constant depth of cut with variable cutting speed and feed rate. Also, the flying distance of chip and it's distribution have been investigated. As a results, good performance of chip breaking can be obtained for small radius of curvature and land width of grooved type chip breaker. And the thickness of chip increase with the increase of feed rate and decrease of cutting speed, and the chip breaking becomes easier with the increase of chip thickness due to the large deformation rate. Obstraction type chip breaker shows better performance of surface roughness than the grooved type. The flying distance of the chips over 90% are less than 1 meter, and the distance decreases as the feed rate decreases.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.47 no.6
• /
• pp.785-789
• /
• 2014

An experiment was conducted to investigate the effects of feeding by different feed types (powder, crumble and pellet) of two different feed formulations with simple dried (D) or extruded (E) conditions on growth and body composition of juvenile sea cucumber Apostichopus japonicus. Triplicate groups of sea cucumber averaging $1.2{\pm}0.05g$ were fed each of the D1, D2, EP1 or EP2 diets for 12 weeks. Survival of sea cucumber fed D2-crumble was higher than that fed EP2-crumble diet (P<0.05). Weight gain of sea cucumber fed EP1-powder was higher than that fed EP1-crumble and EP2-crumble diets (P<0.05). These findings indicated that simple dried feed could use independently feed type for sea cucumber culture and powder type of extruded feed is also good for sea cucumber culture.

• The Journal of Fisheries Business Administration
• /
• v.40 no.3
• /
• pp.189-205
• /
• 2009

This study is aimed to analyze the economic feasibility comparison of the extruded pellets and moist pellets on the Oliver flounder culture farms in Jeju Island. In order to do this, we selected 2 farms (M and S farms) in Jeju Island as a sample. In the study, various analyses including productivity analysis, cost structure analysis, profitability and economic feasibility analysis by feed type were conducted for two sample farms of Oliver flounder culture. The results of economic analysis by feed type on the Oliver flounder culture can be summarized as follows; First, there were not significant differences in productivity by feed type. Second, results of the profitability analysis on farm M by feed type showed the profitability was estimated to be 15.52% and 9.83% in EP and MP, respectively. In addition, the profitability of farm S was estimated to be 28.37% and 33.72% in EP and MP, respectively. Third, results of the economic analysis on farm M by feed type indicated that an internal rate of return(IRR) was 8% and 7% and a benefit-cost ratio was shown to be 1.64 and 1.11 in EP and MP, respectively. Furthermore, the economic analysis of farm M by feed type showed that an IRR was 19% and 24% and a benefit-cost ratio was calculated to be 1.4 and 1.51 in EP and MP, respectively. In summary, it is especially emphasized that economic valuation is not related to feed types (EP and MP). Finally, in order to improve the economic feasibility, it should be more focused on the efficient business management of the Oliver flounder aquaculture.

• Membrane Journal
• /
• v.6 no.1
• /
• pp.44-52
• /
• 1996

For the purpose of the optimal design of a frame and plate type of pervaporation module, model equations which can predict the effects of feed flow condition on the temperature distribution of the feed developed in the module were established and the temperature distribution with feed flow condition was investigated through the model si$$\mu$ation. With increasing the Reynolds number of feed flow in the module, the flow velocity gradient in the channel height-direction as well as the volume rate of feed which acts as energy source for the evaporation of perrneants on the permeate-side surface of a membrane increased to such an extent that both mass and heat flux in the channel height direction could increase and the temperature drop of feed due to the evaporation of the permeant could be reduced correspondingly. A decrease in channel height caused the temperature drop of feed because of decreasing feed flow in the module. It was observed that the si$$\mu$ation result on the effect of Re on the temperature distribution of feed in the module has an agreement with experiment.

• Journal of Animal Science and Technology
• /
• v.66 no.1
• /
• pp.219-231
• /
• 2024

Feed has a great influence on the composition of swine manure, which is the principal cause of odor. Therefore, the purpose of this study is to simply change the shape of pig feed and control calories to find a suitable feed form for reducing the smell of swine manure. The experiment was conducted on 15 pigs from July to August 2021, and a total of three measurements were done. Three types of feed were evaluated in this study. The analysis items related to odor of swine manure are complex odor, ammonia, sulfur-based odors, and volatile organic compounds (VOCs). In the case of complex odor, dilution multiples tended to decrease over time, except for type A feed. The concentration of ammonia in all types of feed decreased over time. Most sulfur-based odorous substances except hydrogen sulfide at the first measurement were not detected. Representatively, Decane, 2,6-Dimethylnonane, and 1-Methyl-3-propylcycolhexane were detected in VOCs generated from swine manure. The major odorous substansces in swine manure have changed from ammonia and sulfur compounds to VOCs. In order to reduce the odor caused by swine manure, it is ad-vantageous to use low-calorie feed consisting of pellet-type.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1603-1604
• /
• 2007

The load of power plants changes every from time to time according to which steam flow of boiler changes. the feed water control is very important for the power plant to be operated in its stability conditions. In case of circulation type boiler, the instability of feed water control leads to instability of drum level control. The higher level of drum water can induce bad quality steam to go into turbine which means the possibility of damage. The lower level of drum water can induce the tubes of boiler water wall to be overheated. In case of once through type boiler, the instability of feed water control leads to bad cooling of superheaters. The less the feed water flow is, the more heated the superheater is. It is necessary for the turbine driving feed water pump to be controlled for the optimal feed water flow in the large capacity power plant. The speed of turbine is controled for the feed water flow. By the way, the optimal control of steam valve is necessary for the speed control of turbine. Therefore, the various kinds of the steam valve structures are introduced in this paper

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.772-778
• /
• 1994

The pervaporation separation experiments of phenol-water mixtures were carried out by using Type 1 (PDMS : crosslinking agent= 1 : 0.25) and Type 2 (PDMS : crosslinking agent= 1 : 0.35) silicone rubber membranes at 30, 40 and $50^{\circ}C$. The phenol concentrations in the feed to be separated were 500 ppm to 5 wt%. Type 2 membranes were more efficient than Type 1 membranes for the separation of phenol-water mixtures. The phenol concentration of 70wt% was obtained for 5wt% of phenol concentration in the feed at $30^{\circ}C$ and 11wt% phenol concentration observed for 500ppm of phenol concentration in the feed at $30^{\circ}C$ by using Type 2 membranes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.1007-1010
• /
• 2002

The accuracy of high speed feeding type laser cutting M/C is the major factor directly concerned with the accuracy of the processed work, and the feed errors of feed system make the machining errors of work directly on processing. In this point, this study focused on the generative elements in feed errors of laser cutting M/C when operating its laser head. In order to improve the accuracy of this machining center, feed errors are measured by a laser interferometer.