• 한국식생활문화학회지
• /
• 제4권2호
• /
• pp.173-176
• /
• 1989

This study was carried out to comparison of the contents of general and mineral components between the original sample and water extract in each part of omija. The content of Carbohydrate was highest in endocarps, and that the crude protein and crude lipid in seeds. The contents of K and Mn in the fruits, endocarps, and seeds were all higher than those of the other cations. The content of K and Zn in endocarps were three to four times as much as those of seeds. and the content of Na, Ca, and Cu in endocarps were 1.5 to 1.75 times of seeds. Mineral contents by water extract in each part were ordered as K, Mg, Ca, and Fe. As the percentage of each ion in water extract on the basis of original sample, Fe was the highest ratio of behavior, and Mn was lowest.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.53-61
• /
• 1996

Effects of carbon and Ti on damping capacity are investigated in an Fe-17%Mn alloy. The suppressive force of carbon against ${\gamma}{\rightarrow}{\varepsilon}$ transformation increases linearly with an increase in its content, lowering Ms temperature and volume fraction of ${\varepsilon}$ martensite. Carbon deteriorates damping capacity by reducing the interfacial area of damping sources and mobility of the boundaries contributing to anelastic deformation. The reduction in damping capacity is accelerated when carbon-containing alloy is aged at higher temperatures above room temperature. The effect of Ti on damping capacity is found to be benificial in carbon-containing alloy, which is attributed to the depletion of carbon solute due to the formation of TiC.

• 한국주조공학회지
• /
• 제3권3호
• /
• pp.174-180
• /
• 1983

The matrix changes and graphite formation in high manganese cast iron (Fe-12Mn-3.5C) are studied with increasing nickel and silicon content. Also, the decomposition of carbides and graphite precipitation are studied by adequate heat treatment.The results obtained in this work are as follows. 1. In high manganese cast iron, fine flakes graphite appeared by adding 5 wt% nickel and A-type flakes graphite can be obtained by adding 7 wt% nickel. 2. Nodular graphite are obtained by graphite spheroidizing treatment with same melt. 3. In high manganese cast iron containing 7 wt% nickel, full austenitic matrix with nodular graphite can be achieved by water quenching after 10 hours' solution heat treatment at $1050^{\circ}C$ in case of containing 2.0 wt% silicon, and 6 hours' at the same temperature in case of containing 2.5 wt% silicon.

• 한국수소및신에너지학회논문집
• /
• 제5권1호
• /
• pp.1-8
• /
• 1994

Lattice structure, hydrogen absorption characteristics, discharge capacity and cycle life of $V_{22}Ti_{16}Zr_{16}Ni_{39}X_7$(X= Cr, Co, Fe, Mn, Al) alloys were investigated. The matrix phases of these alloys were the C14 Laves phase. Chromium-containing alloy had a vanadium-rich phase in addition to the Laves phase. The chromium, maganese, or aluminum-containing alloys had lower hydrogen equilibrium pressure and larger hydrogen absorption content than the cobalt or iron-containing alloys. The discharge capacities of these alloys were 270~330mAh/g. The discharge capacity according to the alloying element X decreased in the order of Mn>Cr>Co, Al)Fe. The charge/discharge cycle lives of the chromium, cobalt or iron-containing alloys were longer than those of maganese or aluminum-containing alloys due to the lower vanadium dissolution rate.

• 열처리공학회지
• /
• 제15권6호
• /
• pp.272-278
• /
• 2002

The changes in damping capacity with volume fractions of thermal and deformation-induced ${\varepsilon}$ martensites were compared and analyzed in an Fe-23%-Mn alloy. The volume fraction of thermal ${\varepsilon}$ martensite increased with decreasing cooling temperature, whereas that of deformation-induced ${\varepsilon}$ martensite increased steeply up to 10%- of cold rolling and nearly saturated in further cold rolling. In the case of thermal ${\varepsilon}$ martensite, the damping capacity increased linearly with the increase in ${\varepsilon}$ martensite content. For the deformation-induced ${\varepsilon}$ martensite, however, the damping capacity increased continuously up to 70%- of ${\varepsilon}$ martensite, over which it decreased suddenly. TEM microstructures showed that the deterioration of damping capacity above 70%- of deformation-induced ${\varepsilon}$ martensite is ascribed to the introduction of perfect dislocations, which play a important role in inhibiting the movement of damping sources such as stacking fault boundaries inside ${\varepsilon}$ martensite, ${\varepsilon}$ martensite variant boundaries and ${\gamma}/{\varepsilon}$ interfaces.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.188-194
• /
• 2009

Recently, new extraction technology for manganese nodule has been developed as alternative noble metallic resources. It is important to understand thermodynamic behaviors of phosphorus in low basic slag system from the viewpoint of the refining processing optimization. Thermodynamic behaviors of phosphorus in the $FeO-MnO-CaO-SiO_2-MgO_{satd.}$ slag system were investigated at 1723 K with various oxygen potential and slag composition of low basicity. The experimental results for dependence of phosphorus on oxygen potential and slag basicity indicated that the dissolution mechanism of phosphorus into slag of low basicity could be derived as follows; $[P]+5/4O_2+(O^{2-})=({PO_{3.5}}^{2-})$ Present experimental results implied that stability of phosphorus in slag would be depended on both of $O^{2-}$ (basicity) and content of $Ca^{2+}$ in molten slag. The thermodynamic effect of FeO, MnO and $Na_2O$ on low basicity on phosphate capacity was discussed.

• 한국토양비료학회지
• /
• 제3권1호
• /
• pp.11-16
• /
• 1970

추락(秋落)에 $SiO_2$와 Mn을 시용(施用)하고 K를 시용(施用)치 않으면 수도(水稻)의 생육(生育)이 조해(阻害)되며 분얼 수가 현저히 감소 된다. K를 시용(施用)치 않은 수도(水稻)는 엽(葉)에 작은 적갈색(赤褐色)의 반점(斑點)이 발생(發生)하였고 엽색(葉色)은 농록색(濃綠色)이 였다. 간장(稈長)은 건전도(健全稻)보다 짧으나 출수(出穗)는 건전도(健全稻)보다 빨렀다. K를 시용(施用)한 수도(水稻)의 근(根)은 굴고, 길고 새뿌리가 나오나 K를 시용(施用)치 않은 수도(水稻)의 근(根)은 생육(生育)이 불량(不良)하고, 가늘고 근부(根腐)가 심(甚)하였다. K를 시용(施用)치 않은 수도(水稻)의 근부현상(根腐現狀)은 "농림육호(農林六號)"보다 "진흥(振興)"이 더 심(甚)하였다. K를 시용(施用)치 않은 수도(水稻)의 생육(生育)은 불량(不良)하나 N, P, $SiO_2$, Fe 및 Mn 함량(含量)은 K를 시용(施用)한 수도(水稻)보다 높다. 추락도(秋落稻)의 Fe 함량(含量)은 $Mn+SiO_2$의 시용(施用)으로 현저히 감소되나 K의 시용(施用)으로도 감소된다. 따라서 $Mn+SiO_2$를 시용(施用)한 무가리(無加里)의 추락답(秋落畓)에 생육(生育)한 수도(水稻)의 근부(根腐)는 K 결핍(缺乏) 때문이며 $Mn+SiO_2$나 K의 시용(施用)은 추락도(秋落稻)의 Fe 함량(含量)을 감소시킨다.

• 한국자기학회지
• /
• 제8권6호
• /
• pp.374-379
• /
• 1998

Mn1-xCrxPt3 합금 박막을 유리기판상에 rf 마그네트론 스퍼터법으로 전이금속(Mn, Cr)과 Pt층을 적층하여 증착한우 열처리함으로써 제조하였다. 제조한 박막들의 소각 및 광각 x-선 회절 분석, 자기 히스테리시스 루우프, 커 스펙트럼을 실온에서 조사했다. 제조한 박막들은 (111)면이 막면에 평행으로 강하게 우선 배향된 AuCu3 형의 규칙합금 구조를 나타냈다. 포화자화는 Cr 치환량(x)이 증가함에 따라 감소하다가 x=0.58 부근에서 영에 가까워진 후 다시 증가하여 x=0.77 이상에서는 거의 일정한 값을 나타냇다. 이것은 페로자성인 MnPt3(x=0)에 Cr을 치환하며, Cr의 자기모멘트가 Mn과 반강자성적으로 결합하여포화자화가 감소하다가 Cr 치환량이 더욱 증가하면 Cr의 기여가 지배적이 되어 다시 증가하기 때문으로 생각된다. MnPt3의 경우에는 자화용이축이 막면에 평행이었으며, Cr 치환량이 증가합에 따라 수직자기이방성이 증가하여 x=0.58 이상에서는 수직자화막이 얻어졌다. 또한, 이 영역에서 Cr 치환량이 증가함에 따라 보자력도 증가하여 x=0.58 이상에서는 수직자화막이 얻어졌다. 또한, 이 영역에서 Cr 치환량이 증가함에 따라 보자력도 증가하여 CrPt3의 경우에는 약 4 kOe의 큰 값을 나타냈다. Cr 치환량에 따른 커 회전각의 변화 추이는 포화지화의 변화 추이와 경향이 유사했다. x=0.77과 x=1의 경우에는 근적외선 영역에서의 커 회전각이 기존의 광자기기록매체인 TbFeCo를 능가했다.

• 한국재료학회지
• /
• 제23권4호
• /
• pp.219-226
• /
• 2013

Activated magnetite ($Fe_3O_{4-{\delta}}$) has the capability of decomposing $CO_2$ proportional to the ${\delta}$-value at comparatively low temperature of $300^{\circ}C$. To enhance the $CO_2$ decomposition capability of $Fe_3O_{4-{\delta}}$, $(Fe_{1-x}Co_x)_3O_{4-{\delta}}$ and $(Fe_{1-x}Mn_x)_3O_{4-{\delta}}$ were synthesized and then reacted with $CO_2$. $Fe_{1-x}Co_xC_2O_4{\cdot}2H_2O$ powders having Fe to Co mixing ratios of 9:1, 8:2, 7:3, 6:4, and 5:5 were synthesized by co-precipitation of $FeSO_4{\cdot}7H_2O$ and $CoSO_4{\cdot}7H_2O$ solutions with a $(NH_4)_2C_2O_4{\cdot}H_2O$ solution. The same method was used to synthesize $Fe_{1-x}Mn_xC_2O_4{\cdot}2H_2O$ powders having Fe to Mn mixing ratios of 9:1, 8:2, 7:3, 6:4, 5:5 with a $MnSO_4{\cdot}4H_2O$ solution. The thermal decomposition of synthesized $Fe_{1-x}Co_xC_2O_4{\cdot}2H_2O$ and $Fe_{1-x}Mn_xC_2O_4{\cdot}2H_2O$ was analyzed in an Ar atmosphere with TG/DTA. The synthesized powders were heat-treated for 3 hours in an Ar atmosphere at $450^{\circ}C$ to produce activated powders of $(Fe_{1-x}Co_x)_3O_{4-{\delta}}$ and $(Fe_{1-x}Mn_x)_3O_{4-{\delta}}$. The activated powders were reacted with a mixed gas (Ar : 85 %, $CO_2$ : 15 %) at $300^{\circ}C$ for 12 hours. The exhaust gas was analyzed for $CO_2$ with a $CO_2$ gas analyzer. The decomposition of $CO_2$ was estimated by measuring $CO_2$ content in the exhaust gas after the reaction with $CO_2$. For $(Fe_{1-x}Mn_x)_3O_{4-{\delta}}$, the amount of $Mn^{2+}$ oxidized to $Mn^{3+}$ increased as x increased. The ${\delta}$ value and $CO_2$ decomposition efficiency decreased as x increased. When the ${\delta}$ value was below 0.641, $CO_2$ was not decomposed. For $(Fe_{1-x}Co_x)_3O_{4-{\delta}}$, the ${\delta}$ value and $CO_2$ decomposition efficiency increased as x increased. At a ${\delta}$ value of 0.857, an active state was maintained even after 12 hours of reaction and the amount of decomposed $CO_2$ was $52.844cm^3$ per 1 g of $(Fe_{0.5}Co_{0.5})_3O_{4-{\delta}}$.

• 한국수산과학회지
• /
• 제41권5호
• /
• pp.315-323
• /
• 2008

To measure the mineral content of fishes, we collected 177 individuals from 53 fish species from the east (Pohang), west (Gunsan), and south (Tongyeong) coasts of Korea. The mean content of the macro mineral in a 100 g sample taken from the edible portion of each fish was (in descending order): P(207.4 mg), K(169.7 mg), Na(101.6 mg), Ca(44.4 mg), and Mg(30.4 mg). In comparison, the mean content of micro mineral in the fishes was (in descending order): Zn ($8.98{\mu}g/g$), Fe ($5.03{\mu}g/g$), Cu ($0.76{\mu}g/g$), Mn ($0.43{\mu}g/g$), and Ni ($0.08{\mu}g/g$). We could not observe clear regional variation in the mineral content of fish species. With regard to minerals considered essential for humans, the amount of Ca per sample (100 g) was the highest in the Scyliorhinus torazame (465.4 mg), and than followed by Ammodytes personatus (338.0 mg), Dasyatis akajei (267.4 mg), Raja kenojei (248.1 mg), Conger myriaster (174.1 mg), Clupanodon punctatus (86.8 mg), Muraenesox cinereus (81.2 mg), and Engraulis japonica (70.4 mg). The daily average intake of the mineral through the fishes consisted of P (100.6 mg), K (82.3 mg), Na (49.3 mg), Mg (14.8 mg), Zn (0.44 mg), Fe (0.24 mg), Cu (0.04 mg) and Mn (0.02 mg). The respective intakes of macro mineral (P, Mg, Na, Ca, K) from the fishes were about 14.4, 4.2, 3.3, 3.1 and 1.8% of the dietary reference intakes for Koreans (KDRIs) set by the Korean Nutrition Society. In comparison, the respective intakes of micro mineral (Cu, Zn, Fe, Mn) from the fishes were about 4.6, 4.4, 2.4, and 0.6% of the KDRIs.